A transmission line of impedance (0.05 + j0.02) pu interconnects the buses of a switchyard and a bulk supply point. The receiving end apparent power is (1.0 + j0.6) pu and sending end voltage, 1/0°pu. Estimate the following: a) receiving end voltage after two iterations b) perform two further iterations to test the convergence of the value of receiving end voltage deduced in a) b) load current c) sending end apparent power

A transmission line of impedance (0.05 + j0.02) pu interconnects the buses of a switchyard and a bulk supply point. The receiving end apparent power is (1.0 + j0.6) pu and sending end voltage, 1/0°pu. Estimate the following: a) receiving end voltage after two iterations b) perform two further iterations to test the convergence of the value of receiving end voltage deduced in a) b) load current c) sending end apparent power

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

2) A 200 ohm resistive load will be matched to a So ohm resstive source impedance. a) Calalate the L-C poss and high pass lumped matching netuwork component Values (tuo sets of L-C vales) b) Sketch the impedonce matching netwark that can be constructed by connec tion of short line segmants. C Assume 15 ohm and 150 ahm characteristic impedance lines are auailable tine lengths for realaing Determine the coriesponding one of the Salutions in part ()
The VSWR on an 50-Ohm transmission line is 5. The distance between successive voltageminima is 80 cm while the distance from the load to the first minimum is 30 cm. What are thereflection coefficient and load impedance
Ql: Choose the correct answer for the following; • Wind turbine is considered one of the prime mover types. (T or F) • Transmission lines are used to (transmit and distribute or distribute and transmit) • The The objective of using batteries is to The alternator converts .... of the prime mover energy or electrical energy into mechanical energy) • Nuclear power station can be produced a .... For the transmission line parameters, the shunt capacitance is the responsible of .... (charging currents or discharging currents) • In short transmission line, the conductor can carry up to The other name of geometric mean radius is The electric field lines originate from. The effect of the capacitance is proportional to the length of transmission line (T or F) • The symbol ɛ represents the .the electrical power generated. and is one of the sources of renewable electrical energy. (water or fuels) energy when the wind stops. (supply or consume) (mechanical energy into electrical amount of…
Develop a small-scale equivalent transmission line pi model (per phase) of the transmission lines with the specification given in table 1. The conductors are placed with a flat horizontal spacing of 7.25 meters. Consider that the load connected against the line 125MW at 0.85 lagging power factor. You are required to develop an equivalent model for a maximum 220V (RMS) sending and receiving end voltage and a maximum of 5A load current. Sr. NTDC Transmission Line Length Conductor No. Туре 220 kV DG Khan-Loralai Transmission Line (227 km) 227km Pheasant TABLE AJ Electrical characteristics of bare aluminum conductors steel-relnforced (ACSR)+ Reniertance Reactance per conductor 1-ft apacing. 60 Ha Ae, 60 Ha Capaitive Aluminum ares, emil Layers of Outaide aluminum diameter, in a/1,000 ft soC, D/ml GMR Induetive Stranding AL/8t De, 20°C. 20C, a/mi Code word D. t Ma-mi Waswing Partridge Ostrieh Merlin Linnet Oriole Chickndee Ibin Pelienn Flicker Hawk 266,800 206,800 300,000 336, 400 336.400…
Derive the power angle equation for a power system network and draw the corresponding curve.
In the circuit given on the side Ra=Rb=Rc=Basic frequency of 13 Ohm loadsit is powered by an AC voltage of f= 60 Hz. Power derived from the sourceits value was measured as Pk=9372.12 Watts. Each switchingthe element is triggered in such a way that it will be at 180 degrees.The DC bus voltage (E=?) and the effective value of the ic phase current(ic rms=?) calculate.
b) A 6052 characteristic impedance transmission line is fed by a DC source of 100V with an internal resistance of 4002. The line is 200m long and has a dielectric constant of 2.25. The load impedance is 12002. Calculate: i. The load reflection coefficient. ii. The source reflection coefficient. iii. What is the voltage at the source terminals just before AND just after 2us?
The load flow data for the sample power system are given below. The voltage magnitude at bus 2 is to be maintained at 1.04 p.u.Determine the set of load flow equations at the end of first iteration by using N-R method. Impedance for sample system Bus Code Impedances line charging admittance 1-2 0.08 + j0.24 0.0 1-3 0.02 + j0.06 0.0 2-3 0.06 + j0.18 0.0 Schedule of generation and loads: Bus Code Assured Voltages Generation Load…
Complete the sentence The power factor must be close to ……………. To insure that losses in the transmission lines will be reduced
For the given power transfer, a star system is associated with larger line currents and a delta system is associated with a larger line voltage. Select one: O True O False Jump to...
A transmission line of impedance (0.05 + j0.02) pu interconnects the buses of a switchyard and a bulk supply point. The receiving end apparent power is (1.0 + j0.6) pu and sending end voltage, 1/0°pu. Estimate the following: i) Receiving end voltage after two iterations ii) Perform two further iterations to test the convergence of the value of receiving end voltage deduced in (i) iii) load current
Q. 13. Transmission systems that produce switching surges higher than lighting surges are the ones that operate at: A. 200 kV B. 300 kV C. 400 kV D. B and C Q. 14. When constructing volt time curve, if flashover occurs on the tail side of the wave, the point on the curve will have a voltage magnitude equal to: Whos A. The applied wave peak B. The applied wave flashover point C. The applied wave peak multiplied by a factor of 0.9 D. The applied wave flashover point multiplied by a factor of 0.9