Instruction: Show complete solution with proper derivatives/integrals and units. Box or indicate your final answers when solving. Use 2 decimal places for final answers. If not stated, use ? = 9.81 m/s^2 (Dynamics of Rigid Bodies) Need by 1 hour. A toy gun uses a 0.2-gram pellet as its ammo. The toy uses twoparallel springs each with k-500 N/m to propel the pellet. Find themaximum height if the spring needs to be compressed by 2cmbefore firing. Neglect air resistance as the pellet travels.

Finding maximum height when the spring compressed by 2cm

A toy gun uses a 0.2-gram pellet as its ammo. The toy uses two parallel springs each with k-500 N/m to propel the pellet. Find the maximum height if the spring needs to be compressed by 2cm before firing. Neglect air resistance as the pellet travels.

A toy gun uses a 0.2-gram pellet as its ammo. The toy uses two parallel springs each with k-500 N/m to propel the pellet. Find the maximum height if the spring needs to be compressed by 2cm before firing. Neglect air resistance as the pellet travels.

Residential Construction Academy: House Wiring (MindTap Course List)

5th Edition

ISBN:9781337402415

Author:Gregory W Fletcher

Publisher:Gregory W Fletcher

Chapter4: Test And Measurement Instruments Used In Residential Wiring

Section: Chapter Questions

Problem 12RQ

See similar textbooks

Related questions

Q: The probability that the annual maximum flood discharge will exceed 25000 m³/s, at least once in…

A: Using formula

Q: re welded to a rectangular web plate. Dimensions of the cross section are: = 430 mm = 16 mm = 110 mm…

Q: 1. A city of 6000 population has an average total consumption per person per day of 100 gallons.…

Q: It takes an airplane one hour and forty-five minutes to travel 500 miles against the wind and covers…

A: Answer Distance = 500 miles Time taken against wind =1.75 hr (one hour and forty five minutes) Time…

Q: The following statements are true about the road design except: Only commercial vehicles of more…

A: Road design refers to the plan and layout of a construction project for a road.

Q: A 0.005-g sample of a rock is to be analyzed, and iron is to be determined at the ppm level.…

Q: ng at a constant speed of 130 kph at a location where the speed limit is 100 kph. A police office e…

A: Find speed of car P & car A Vp =160 km/h =44.444 m/s VA =130 km/h =36.1111 m/slet t1 =time car P…

Q: A double acting reciprocating pump having piston area 0.1m² has a stroke length 3 0.30m. The pump is…

A: Given data: Piston area, A = 0.1 m2 Stroke length, L = 0.30 m Pump discharging rate, φac=2.4…

Q: Q1 // Determine the ultimate moment. For the sin Fig. below when the fe' = 21 Mpa, fy = 400 Mpa

A: Given depth in fig. is effective depth (d) = 530mm For determining ultimate moment, we need to first…

Q: Determine the magnitude of the resultant force. The magnitude of the Resultant force is nearly 40°…

A: The two forces are F1=500NF2 =200NThe angle between two forces, α =40°

Q: 1. When a 10-kg object is placed on top of a vertical spring, the spring compresses a distance of…

Q: View Policies Show Attempt History Current Attempt in Progress The stresses shown act at a point on…

A: Using transformation equation

Q: Q4: If the height of the flood hydrograph resulting from a 6-hour rainstorm is over a certain…

Q: 3. A 0.2 kg mass rests on top of a spring that has been compressed by 0.4 m. The force constant for…

Q: 3.66 A long water trough of triangular cross section is from two planks as is shown in Fig. P3.66. A…

A: Apply Bernoullis theorem P1γw+v122g+z1=P2γw+v222g+z20+0+h=0+v22g+0v2=2ghusing continuity equation…

Q: (Round to 3 dec places) A simple curve having a radius of 140 m have tangents with bearings of N 20°…

A: Given values: Tangent 1 = N 20° E forward; Tangent 2= N 75°E back Radius, R = 140 m Stationing of PC…

Q: Q4: Three pipes A, B and C, are interconnected as shown in figure (4). The pipes characteristics are…

Q: 12: For the given figure, r₁ = 30 m r₂ = 10 m H = 20 m t = 15 m Q = 13 L/s h = 13.6 m h₁ = 17.6 m h₂…

Q: If (P) is principal amount, (i) is * Spenns the rate of interest and (n) is the number of periods in…

A: Given data Compound interest i is the rate of interest which is per year compounded .but we…

Q: Determine the nominal moment capacity M, iffy = 60,000 psi and f' = 3600 psi. Check the section to…

A: Nominal moment capacity The nominal moment capacity of an RC beam is calculated using the…

Q: Determine the water flow rate of hydraulic system shown in Fig. (neglected the . minor losses) $00…

A: Applying Bernoulli's equation at two water surfaces incorporating frictional headloss the value of…

Q: 6. If the pressure at a point in the ocean is 1400 kPa, what is the pressure 30 m below this point?…

A: Given data in question Pressure Depth Specific gravity To find out Pressure at some depth

Q: Consider a point in a structural member that is subjected to plane stress. Normal and shear stress…

A: Given data: Sx=-12 ksiSy=33 ksiSxy=17 ksi

Q: 5-A 10ft continuous flexible strip footing is subjected to a load of 500 psf. Find the change in…

A: Given data: Strip footing. q=500 psfB=10 ftz=3ft

Q: Two pipes of lengths 2500 m each and diameters of 90 cm and 70 cm respectively are connected in…

A: Given Total flow= 250 litres / sec

Q: In Midpoint Method, a2 is equal to

A: This question is from surveying.

Q: Using the following notes, what is the elevation of BM14? Station BS FS…

A: Using the following notes, what is the elevation of BM14?

Q: B: A closed cylindrical tank filled with water has a hemispherical dome and is connected to an…

A: Explaination:- Pascal's law expresses that anytime in a liquid, pressure is free of movement and…

Q: The built-up section shown below is fastened together by passing two 10 mm diameter rivets through…

A: For Given ; IPE 400 X 180 h = 400 mm b = 180 mm IXL = 23130 cm4 = 2.313 × 108 mm4 Ix = 2.313 × 108…

Q: A water tank full of water of 5 m wide, 8 m long and 4 m high, calculate the pressure (in psi) at…

Q: Calculate the cost required to construct a premix layer having bulk specific gravity of 2.239 and…

A: Solution: Given: width = 7m length = 2 km Thickness = 46 mm Bulk specific gravity = 2.239 material…

Q: Draw the influence line for the force in (a) member JI and (b) member EF. Ar L B K poddo 1080 D…

Q: For a sandy soil, the effective stress failure envelope is given as t= tan30. Find the deviator…

A: Find the deviator stress at failure for a sample?

Q: An open tar ank conta от и OT Oll (s=0.75). Calculate the pressure at the bottom of the tank.

A: given water depth, Hw = 5m Oil depth, Ho = 2m specific gravity of oil = 0.75, Required: Pressure…

Q: The most command bond of bricks is The most command type of deep foundation is ........in Iraq

A: Bond of bricks The bond in brick masonry is the orderly placement of brick units that make up a…

Q: problem: A Pelton wheel has a mean bucket speed of 10 meters per second with a jet of water flowing…

Q: 7.20 A saturated clay stratum draining both at the top and bottom undergoes 50 per cent…

A: Given :

Q: Describe the crack appearance and development from the beginning of compression to failure when a…

A: There are numerous reasons due to which cracks develops in the masonry specimens. Some of them are…

Q: I. Problem Solving. Use 3-decimal places. All solutions must have rigorous explanation. PROBLEM NO.…

Q: problem: A Pelton wheel has a mean bucket speed of 10 meters per second with a jet of water flowing…

A: Given ;

Q: The table below represents the flow information for a river, follow the flood hydrograph of this…

A: Final value of discharge are solved as Q3 and Q4 discharge values given in solution.

Q: Block C is moving upward at 12 in/s. @AB 5 in. 45° B 4 in. 30°

Q: F2-4. Determine the horizontal and vertical components of reaction at the roller support A, and…

Q: 4- Coefficient of friction is the A. Angle between normal reaction and the resultant of normal…

A: B. Ratio of limiting friction and normal reaction

Q: use discontinuity functions to compute (a) the slope of the beam at B and (b) the deflection of the…

Q: A compound shaft consists of segment (1), which has a diameter of 1.5 in., and segment (2), which…

A: Solution: Given: P = 14 kips Segment 1: diameter =1.5 in. TA = 5 kip·in Segment 2: diameter = 2.2…

Q: Prepare a schedule of bars for the R.C.C. Lintel shown in the fig. 4-²

Q: (1) Determine the center of gravity about the indicated x- axis in mm. 2). Determine the center of…

Q: A shaft is subjected to torsional moments as shown in figure. Plot the torsional 3 kN-m 5 kN-m E…

Q: 4.5 ft 1.5 ft 1.5 ft 2.5 ft 3.5 ft The crate weight is 270 lb. The minimum force p for tipping is…

Question

Instruction: Show complete solution with proper derivatives/integrals and units. Box or indicate your final answers when solving. Use 2 decimal places for final answers. If not stated, use ? = 9.81 m/s^2 (Dynamics of Rigid Bodies) Need by 1 hour.

A toy gun uses a 0.2-gram pellet as its ammo. The toy uses two
parallel springs each with k-500 N/m to propel the pellet. Find the
maximum height if the spring needs to be compressed by 2cm
before firing. Neglect air resistance as the pellet travels.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

a. If the mass of bullet is 5g and the mass of the gun is 10kg and the velocity of the bullet is 300m/s, find the recoil speed of the gun Answer V= 0.15m/s b. An aero plane flying at 250m/s takes air into its engine at a rate of 500kg/s. Fuel is burnt at 20kg/s. The engine expels gases at a speed of 600m/s relative to the jet. Calculate the driving force of the engine (187000N)
The 50-mm-diameter cylinder is made from Am 1004-T61 magnesium and is placed in the clamp when the temperature is T = 15°C (Figure 1) Figure 1 of 1 100mm 150mm
4G 4G 11:16 0.10 KB/s 65% ES 23 module-1a CE23-Mechanics of Deformable Bodies SOUTH EAST ASIAN INSTITUTE OF TECHNOLOGY, INC. Page - 16 - of 17 Plate No. 1 1) A circular aluminum tube of length L = 400 mm is loaded in compression by forces P (see figure). The outside and inside diameters are 60 mm and 50 mm, respectively. A strain gage is placed on the outside of the bar to measure normal strains in the longitudinal direction. (а) If the measured strain is e 550 10 6, what is the shortening d of the bar? If the compressive stress in the bar is intended to be 40 MPa, what (b) should be the load P? Strain gage P P L = 400 mm 2) Determine the normal stresses in members FE, FC, and BC and state whether they are in tension or compression. Atension = 3000 mm2, Acompression = 3500 mm?, 4 kN 2 kN 2 kN 3 m 3 m 1.5 m 1.5 m -1.5 m- 3 m -1.5 m→ 3) Determine the normal stresses in members AB, BD, AC and BE and state whether they are in tension or compression. Atension = 2000 mm², Acompression = 2250…
calculations of moment of inertia, Bending strength & Bending stiffness for the pipe cross-section of (outer diameter 1.25in and the wall thickness of 1.6mm) Of material AISI 4130 having the yield strength of 460mpa
A single way valve that lets air into the pneumatic system but doesn't allow the air to return back in same path is known as O Thvee-way valve O check vahve O Direction control valve O Receiver valve
21. The maximum size of ferrules that can be safely used with 150mm mains is: B) 20mm D) 10mm A) 25mm C) 15mm
1. A pump station design fills a pressurized water tank by pumping water from a reservoir. The flow rate is 0.75 cfs. The pump is 10 feet above the reservoir, and the water tank is 100 ft above the pump. The pressure in the water tank is 10 psi. The suction and discharge lines are both (actual diameter) 6-inch Sch 40 steel (pipe roughness = 0.00015 ft). Use a kinematic viscosity of 1.21 x 10-5 ft²/s. Total pipe length is 200 ft. The suction line is 10 ft. You must account for friction loss, but you can neglect the minor losses. a. What is the head added by the pump in ft? b. What is the power added by the pump in HP (recall 1 HP = 550 ft*lb/s)? 110 ft 10 ft 0 ft
Task 3: Fluid Mechanics Lab Meters You studied the SAYBOLT viscometer in the fluid mechanics lab to determine 20W50 Motor Oil viscosity. Follow the following steps to do your task.
A resonant circuit using a 286-nF capacitor is to resonate at 18.0 kHz. The air-core inductor is to be a solenoid with closely packed coils made from 12.0 m of insulated wire 1.1 mm in diameter. The permeability of free space is 4 x 107 T-m/A K ▼ Part A How many loops will the inductor contain? Express your answer as an integer. G| ΑΣΦ N = 14530 Submit Previous Answers Request Answer ? X Incorrect; Try Again; 5 attempts remaining
Q5: The compart ments (B) 4 Cc) in figure below are closed & filled with air. When the gauges (A) f (D) read as indicated, what should be the value of Cx) for gaugeCE)? (Mercury in each U-tube gauge) 2.07 bar 254 Air Air E.
23 32 Q12) The pressure gauges 1, 2 and 3 are installed on the system as shown. If the readings of the gauges be Pi -1 bar, P2 - 2bar and P3 - 3 bar, what will be the value of P? (Take Paim = 1.01 bar) http://www.sanfoundry.com wp content'uploDads/2017/0e/ fluid-mechanics-questione-answers-pres sure-drtritutiun-contant-density-fluid- 1 9s png Ctri Click to follow link 3 meetgoogle com is sharng your screen. Stop sharing Hide ntpsu/waw.sarfoundry.con.wp-contentiupicads/2017/06/fluid-nechanici- 1029 AM P Type here to search ロ ENG 3/0/221
II Find the head of internal mouthpiece (running fulI), a diameter and discharge of the mouthpiece are 150mm and 32 liter/sec 圖 A- BI