A tilting level is used to run a set of precise levels to a construction project from benchmark DAM, whose elevation is 101.865 m. The line is run along a road that goes up a steep incline. To expedite the job, backsight distances are kept to 50  1 m and foresight distances are 20  1 m. The total length of differential levels is 4410 m. The elevation difference observed is 13.634 m. What is the corrected project elevation if the instrument has a sight line that declines at the rate of 0.3 mm per 50 m?

Q: Q1) A railway embankment, 12 m wide, with side slop 11 2:1 is to be calculated for its volume of…

A:

Q: an elevation of 240.600 m. If the maximum allowable rate of change of grade for this curve is 0.15%…

A: Find…

Q: N 1200N 400 mm 150 5 mm tipico 20 mm 25 mm 20 mm (b) 45 mm

A:

Q: A vehicle is to be propelled by a jet of water impinging on a vane as shown in Figure 4.7. The jet…

A: This problem is solved using Momentum_impulse Equation.  At point A, the velocity is resolved into…

Q: 9. List the relations that control the connection of pumps in parallel, when we use this type of…

A: Pumps are connected either in series or parallel . Based on requirements what we have to achieve…

Q: A 443-lb block is resting on a rough horizontal surface for which the coefficient of friction is…

A: Given data Weight of Block Equal to 443 LB Coefficient of friction is equal to 0.4 We are asked to…

Q: Determine the strain energy of the beam shown in the figure below. The cross-section of the beam is…

A: Given,  Our aim is to determine the strain energies.  E= 200GPa d1=100mm and d2=50mm So, let's get…

Q: The cross-section notes shown below are for a ground excavation for a 10m wide roadway. STA 15+900…

A:

Q: 3. Determine the strain energy of the beam shown in the figure below. The cross-seu beam is circular…

A:

Q: Looking at the x direction, provide the front view, top view, and right-side view using the meter…

A: The isometric Front, top, and bottom of the Drawing are given below:

Q: 3. For the piping system shown, the flow rate is 18 ft³/s of water (p = 1.94 slugs/ft³). Compute the…

A: Calculation of Pressure drop between junction point and Discharge in Each pipe####

Q: CLASS WORK 1: 2m 2.5 2m 1.5m 4KN 5KN 6KN A. SOLVE THE VERTICAL REACTION IN THE ROLLER SUPPORT. 4…

A:

Q: 4. Calculate the force exerted on a stationary curved vane that deflects a 0.025-m-diameter stream…

A:

Q: Problem 3. Draw the shear and moment diagrams for the beam. 10 kN 5 kN 5 kN B 2 kN/m 4m 3m2 m2 m-3m-

A:

Q: A rectangular beam has a width of 300 mm and an effective depth of 500 mm. It is reinforced with…

A: Answer We are given width b = 300 mm effective depth d = 500 mm Tension side reinforcement As= 4 -32…

Q: 3. Determine the strain energy of the beam shown in the figure below. The cross-section beam is…

A:

Q: The rigid bar ABD of negligible weight is originally horizontal and is supported by two steel cables…

A: Appreciate if there is detailed work with explanation and finds you helpful for ease of…

Q: A rectangular channel with a flow rate of 600 L/s has a flow depth of width of 2m. Assuming n=0.012…

A:

Q: What are the underlying assumptions when calculating for the upper and lower bounds of the elastic…

A: he lower-bound estimate of elastic modulus is calculated by: Ec = 1 / (ff / Ef + (1 – ff) / Em). On…

Q: A gate 2 m high and 4 m wide is flush with water at the top. Determine the moment at the bottom in…

A: In this question a gate is given which is 2 m high and 4 m wide We have determine the moment at the…

Q: Given the following data for a closed traverse. Line Length Bearing AB 23.06 N 31° E BC 23.70 N 43°…

A: For a closed traverse summetion of all latitude is zero. Also summation of all departure is zero.

Q: Problem I. A steel beam cross section is assembled as shown by bolting the channel, C200 x 27.9,…

A:

Q: Mohr's Circle 9-7 933. For the state of stress shown in Fig. P-933, determine normal and shearing…

A:

Q: The face of a vertical dam has the shape of an isosceles triangle of altitude 4 m with an upper base…

A: Given, H = 4 m  B = 6m

Q: Smooth pipe: d=50mm P1 1 10 m I 40m->> 20m 80 m Open jet

A:

Q: 3. Determine the strain energy of the beam shown in the figure below. The cross-s beam is circular…

A:

Q: s to be made of steel having an ultimate shearing stress of 400 MPa, determine: (a.)The diameter of…

A:

Q: 933. For the normal and shearing stresses on the planes whose normals are at +60° and +150° with the…

A: σx=-10 MPa                                ∵σx and σy is compressive σy=-10 MPaτxy=20 MPa…

Q: 12.22 0+000 11.32 0+020 8.82 0+040 16.38 6.62 0+060 0+080 10.35 0+100

A:

Q: Problem 2.4 On the basis of isopluvial maps, the 50 years 24 hr maximum rainfall at Bangalore is…

A:

Q: 1. Is there a difference between the values of the nozzle velocity (v₁) and the jet velocity (v₁)?…

A: “Since you have asked multiple question, we will solve the first question for you. If you want any…

Q: For the beam subjected to the loadings as shown, determine the following: 52 kN 40 kN/m 2m 4m B 2m C…

A: a. draw the shear and moment diagrams specifying values at all change of loading positions and at…

Q: mine the support reactions at B and the location deflection for the beam with built-in ends. 1.5…

A:

Q: Using the slope-deflection method, draw the bending moment diagram. 3m B 3m 2EJ 4m 6. Moment @ CD…

A: In above structure, three displacement are unkown ( slope at B and C and Horizontal deflection at B…

Q: Determine the equations for shear and bending moment for the beam shown.

A: Shear force and bending moment The algebraic total of the vertical forces at any segment of a beam…

Q: What will be the pressure head of a point in mm of Hg it

A: This question is from Fluid mechanics

Q: At room temperature (20°C) a 0.7-mm gap exists between the ends of the rods shown. At a later time…

A:

Q: determine the SSD (ft) provided on the curve.

A:

Q: cube with 20-cm-long sides is sitting on the bottom of an aquarium in which the water is one meter…

A:

Q: The cross-section notes shown below are for a ground excavation for a 8m wide roadway. STA 16+200…

A:

Q: The truss shown is constructed using 2L8x8x1/2 members. P = 120kips and L = 7ft. 2P P 60° 45° D…

A: As per Bartleby's guidelines we are supposed to answer only first three questions. Kindly repost…

Q: For the figure shown below, find the equivalent permeability of the system if K2-3K1: K3=2K1:…

A:

Q: Find the moment at A a. 81.36 kN-m b. 116.64 kN-m c. 220.44 kN-m d. 258.63 kN-m

A:

Q: Forward Backward Bearing Bearing S. 37'30' E. N. 37'30' W. S. 43'15' W. N. 44 15 E N. 73'00' W. S.…

A:

Q: A vertical bar consists of three prismatic segments A₁ (between A and B), A₂ (between B and D), and…

A:

Q: Problem 5. (HKS Problem 7.16) For the cases in the figure below, determine the pressure, elevation…

A: GIVEN:  TO CALCULATE: Pressure, Datum/Elevation, Total head at entry, exit and at point A of the…

Q: Section A A solid shaft is firmly held at both ends and carries two comparatively thin disks, as…

A: Answer (i) Calculation of Rotation  We know that Relation between the Torque and rotation is given…

Q: Compute the parameters of a simple curve. PI = Sta 1+395.43 | = 43° 39' Arc basis, D = 4° 15'

A: ###Calculation of parameters of simple  curve###

Q: Determine the strain energy of the beam shown in the figure below. The cross-section of the beam is…

A:

Q: The face of a vertical dam has the shape of an isosceles triangle of altitude 4 m with an upper base…

A:

Coordinate Geometry of Survey

Coordinate geometry (COGO) is a method of inserting surveying or engineering data into geographic information system (GIS), computer-aided design (CAD), or mapping software. These data can be collected on the proposed construction site using standard surveying techniques and instrumentation or may be taken from existing maps, engineering plans, drawings, or records. Data gathered on the site includes coordinates of points, bearings, and distances between points. The data are noticed and noted through conventional surveying procedures, like a traverse or layout measurement series and it can be either digital or non-digital. The maps and plans are inclusive of boundaries, divisions, and other components, and these features are shown with coordinate values, the lengths, offset distance, and bearings between them.