A T-section having a cross section shown has a span of3.6 m. The location of the neutral axis is located 130 mmfrom the bottom of the beam.Elastic moment of inertia of the beam200 mm40mm160mm50 mmWu3.6 m| = 58.13 x 106 mm4Fy = 250 MPa%Da. Compute the yield moment capacity of the beam.b. Compute the plastic moment capacity of the beam.c. Compute the shape factor. (S.F. = Z/S)

Answered: Image /qna-images/answer/23913ceb-914e-402a-b045-a5fb8d17594b.jpg

Answered: A T-section having a cross section…

A T-section having a cross section shown has a span of 3.6 m. The location of the neutral axis is located 130 mm from the bottom of the beam. Elastic moment of inertia of the beam 0 mm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An aluminum bar having a cross-sectional area of 160 mm? carries the axial loads as shown in the Figure below. Assume that the bar is suitably braced to prevent buckling and E = 70000 MPa. The length of each bars are follow: B, = 0.8 m; B, = 1.0 m; B3= 0.6 m. Determine the axial load acting on bar Bị in kN. 35KN В1 B2 ВЗ ... 10KN 15KN 30KN Determine the axial load acting on bar B2 in kN. Determine the axial load acting on bar B3 in kN. Determine the axial stress of bar B1 in MPa. Determine the axial stress of bar B2 in MPa. Determine the axial stress of bar B3 in MPa. Determine the total deformation of the bars B1, B2 and B3 in mm. Determine the deformation of the bar B in mm. Determine the deformation of the bar B2 in mm. Determine the deformation of the bar Bz in mm. 35 А 35 B 20 10
A beam cross section is shown. If the beam is subjected to a moment of 400N.m, the maximum bending stress will be? I, = 200 mm 4 8 mm 4 mm O a. 16GPA О Б. 10GPa 12GPA O d. 8GPA
If the beam is subjected to an internal moment of M = 30 kN.m, determine the maximum bending stress in the beam. The beam is made from A992 steel. Sketch the bending stress distribution on the cross section. 50 mm 50 mm 15 mm 10 mm M 150 mm 15 mm
02 A cast-iron beam has a section as shown in the figure below. The beam is subjected to two concentrated loads of 3kN. The N.A is located at 35 mm from the bottom and that maximum flexural tensile stress =20 MPa. Determine the width (X) of the flange. 20mm 3kN 3kN 120mm 15m 35mm 20mm 2m 3m 2m
150 mm 6 mm B 100 mm. i The beam has simple supports and an overhang and is subjected to a point load and a uniform load as shown in the figure below. 12 KN q = 4.8 kN/m с 3 m Calculate the maximum tensile and compressive stresses of the beam. Assume that Ew sign convention.) MPa maximum tensile stress in wood MPa maximum tensile stress in steel MPa maximum compressive stress in wood MPa maximum compressive stress in steel B 900 1m = 11 GPa and Es 200 GPa. (Enter your answers in MPa. Use the deformation =
A:Y 211O 2_531929016114... -> A rod is composed of an aluminum section rigidly attached between steel and bronze sections, as shown in Figure below. Axial loads are applied at the positions indicated. If P = 11 KN and the cross sectional area of each rod is 312.5 mm, determine the stress in each section. 4P Steel Bronze |Aluminum 609.6 mm 914.4 mm 762 mm
QUESTION 1 The assembly consists of two rods and a horizontal bar BC. Each of the rod AB and CD is made of aluminum and has a cross-sectional area of 125 mm2. A point lqad of 5 kN is applied at point E were located 0.20 m from B. Knowing that they support the rigid member BC, calculate the deflection of point E. Modulus of elasticity for aluminium is 75 GPa. P- 5 kN 0.36 m E B C 0.44 m 0.20 m
G6//The light rigid bar ABCD shown in Figure is pinned at B and connected to two vertical rods. Assuming that the bar was initially horizontal and the rods stress-free, determine the stress in each rod after the load after the loadP = 20 KN is applied. Steel L=2m A=250mm 4m E=200Mpa C. Aluminum L=2m A=500mm2 2m 2m E-72Mра P=20KN
Problem 3: Put 32.5 into a steel tube 2.4 meters long, 34 mm radius and 1.5 mm thick. A circular bar made of aluminum with a radius of mm is inserted and these two materials are they are linked together to form a cross section that will work. This cantilever beam obtained from end A it is fixedly supported. This cantilever beam, A torque of T = 900 Nm from end B (torque) is applied. Stiffness modulus of steel, Ge 2.4 m 77 GPa and the modulus of stiffness Gal = 26 for aluminum Since GPa is the rotation at point B What is the (torsion) angle? Calculate.
A built-up tee-steel shape is shown in the figure. Bending is about the x-axis and the steel is A572 (Fy = 350 MPa). -Determine the moment of inertia of the section in ____ x 108 mm4.0 -Determine the yield moment in KN.m.0 -Determine the location of the plastic neutral axis from the top in mm.0 -Determine the plastic section modulus in ____ x 106 mm3.0 -Determine the plastic moment in KN.m.0
Q2/ The beam shown is made of a nylon for which the allowable stress is 24 MPa in tension and 30 MPa in compression. Determine the largest couple M that can be applied to the beam. 40 mm 15 mm M d = 30 mm 20 mm
A beam having the cross section shown is subjected to a couple M0 acting in a vertical plane. Determine the largest permissible value of the moment M0 of the couple if the maximum stress is not to exceed 103 MPa. Given: Iy = Iz = b4/36 Iyz = b4/72