QUESTION 12A system is made of two masses, m, and m2. (m, = 2m2).A frictionless pulley and a cable are installed as shown in Figure and the masses are thenreleased.What is the behaviour of the system?m1m2Hs=0.1Hx =0.0730°50°O1.Moves towards left.O 2. Moves towards right.O 3. Not moving.O 4. Moves towards left for 1.2 s, then towards right.O 5. Moves towards right for 1.2 s, then towards left.

Answered: Image /qna-images/answer/b193a4bd-2dab-460c-b74a-c2302d959388.jpg

Answered: A system is made of two masses, m, and…

A system is made of two masses, m, and m2. (m, = 2m2). %3D A frictionless pulley and a cable are installed as shown in Figure and the masses are then released. What is the behaviour of the system?

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

PROBLEM 3: Given the system below; (a) Draw the free body diagram of the system (SO1.1); (b) set-up the equations required in solving the problem (SO1.5), and (c) determine the angle, 0, to ensure that the 100lb body will not slide down. (SO1.3). - IDEAL PULLEY IDEAL PULLEY ,Ms=O.466 we 100 Ib 100 l6. P=?
STATIC I need the answer within 1 hour. Thanks Using the knot method, find the force that each element in the truss system carries. Indicate whether these elements are under tensile force or under compression force. F1(N)=11 , F2(N)=23
Quantity Trial 1 Trial 2 F1 (dynes) 93100 dyn 102900 dyn F2 (dynes) 68600 dyn 107800 dyn F3 (dynes) 102900 dyn 117600 dyn F4 (dynes) 34300 dyn 78400 dyn On a separate sheet of paper or graphing paper, using polygon method (one for each trial), connect all the forces F1, F2, F3 and F4. What is the resultant force? What do you observe?
In the following figure the lamp has weight, in magnitude, of W, the spring constant is k for the spring AB, the equilibrium length of the spring is lo, the horizontal distance between C and B is d and the angle measured clockwise from the negative x-axis to AC is 0. With the provided values to follow, determine the required length of cable AC so that the system is in static equilibrium. All angles are measured in degrees, all distances are measured in m and all spring constants are measured in Nm¹. Provide your answers accurate to three significant figures. Given -50. w-200, 200, d-2 and 0.5 (all forces measured in N), provide the required values (where is the magnitude of the tension in the rope): T = AC =
Question 1 A 125 kg electric motor and a 505 kg reciprocating compressor are mounted on a common support. The motor runs at 2402 revolutions/minute (rpm) and by a belt drives the compressor at 3600 rpm. It is found that the vertical force fed to the support is excessive. Choose four equal springs to provide a force transmissibility not exceeding 4%.
Q2/A belt drive consist of two V– belts in parallel, on grooved pulleys of the same size. The angle of the groove is 30°. The cross – section area of each belt is 750 mm? and u is 0.12. The density of the belt material is 1.2 Mg/m³ and the maximum safe stress in the material is 7 MN/m?. Answer the following questions 1- The centrifugal tension in belts is (a) increases power transmitted (b) decreases power transmitted (c) have no effect on power transmitted (d) increases power transmitted up to a certain speed and then decreases
TOPIC: F=ma (Newton’s 2nd law of Motion) Given the figure below, determine the tension in the three cords (in KN) if the initial pull of the motor is 0.20 m/s, and increased 0.50 m/s each added second. PLEASE ANSWER WITH COMPLETE AND DETAILED SOLUTIONS. THANK YOU
Item 2 Consider the following hanging mass system for the following problems. Before answering the questions below, draw two separate free-body diagrams of ring C and then ring B. Be sure the FBDS are neat a properly labeled. You will turn them in with your written work. (Figure 1) Figure 30° E 45° F 1 of 1 Part A cb Deturmine the tension developed in cable if cylindar E weighs 40 lb and 0= 15°. FCB= Submit ▾ Part B WF = 5 ΑΣΦ 11 vec Submit Request Answer If cylinder E weighs 40 lb and 0 = 15°, determine the weight of cylinder F. Express your answer with the appropriate units. 15. ΑΣΦ ↓↑ vec ? Request Answer ? lb 2 of 5
Item 1 used to intermittently operate a piece of equipment at the end of a lifter arm. The lifter is in contact with the highest point of the cam at the instant shown and the lifter is constrained to move only in the vertical direction. The cam has a radius of r = 4.5 in and is rotating about point O, which is offset from the center by a distance c = 3.0 in. The cam's angular position is measured from the positive x axis and is positive clockwise. The angular velocity and acceleration are positive clockwise. (Figure 1) Figure (0,0 36°F Clear r W 1 of 1 Par Find align Expr Vie Omin Subn Provide Feedb
Equilibrium of Concurrent Force System. The piston of a reciprocating engine exerts a force of 175 kN on the crosshead when the crank is 45° (angle B) past TDC. If the stroke of the piston is 800 mm and the length of the connecting rod is 1.80 m, find the guide force and the force in the connecting rod. Hint: 1=½ stroke; Angle o may be solved using Sine Law in AACO. K= Compressive Force in the connecting Rod E= Piston Effort 70 120 F, = Guide Force Fig. P-1 Fig. P-2 a Tools: EF cos0=0; F sin .=0. R = Ev)* + (E#): ; R 771 =- : tane = sin A sin B sin C
Equilibrium of a particle: ΣF = 0 .. ΣF = 0 and Fy Find the tensions in the two cables which are supporting a load of 10 kg. h = 2.5 m, d₁ = 3.75 m, and d₂ = 3.75 m. Give numeric answers to three significant figures. e) h AC = d₁ BC= α с X W d₂ Substitute the known weight and angles a and B into your equations, then solve them simultaneously to find the tensions in cables AC and BC B -B
Problem 1: The surface of the inclined plane is smooth (no friction). The inclination is 0, with sin0 = h/L, where h is the height of the right end, and L is length of the plane. A box called G (note this is not the weight) is lying on the surface with a pulley system shown in the figure. The mass of the box is m. The box is in equilibrium. (1) Plot the free body diagram for the box G %3D . Calculate the magnitudes for the 3 forces. (T (2) Calculate the force F that is required for the system to remain in equilibrium. es=