A student prepared a buffer solution using 60.00 mL of 0.2025 M acetic acid and 56.98 mL of 0.10993 M NaOH. Given this information, what is the stoichiometric concentration of Ac in their buffer? Report your final answer, in mol/L, to 5 decimal places and only include the numerical value (no units). Do not use scientific notation to answer this question.

A student prepared a buffer solution using 60.00 mL of 0.2025 M acetic acid and 56.98 mL of 0.10993 M NaOH. Given this information, what is the stoichiometric concentration of Ac in their buffer? Report your final answer, in mol/L, to 5 decimal places and only include the numerical value (no units). Do not use scientific notation to answer this question.

World of Chemistry, 3rd edition

3rd Edition

ISBN:9781133109655

Author:Steven S. Zumdahl, Susan L. Zumdahl, Donald J. DeCoste

Publisher:Steven S. Zumdahl, Susan L. Zumdahl, Donald J. DeCoste

Chapter16: Acids And Bases

Section: Chapter Questions

Problem 8STP

See similar textbooks

Similar questions

Each symbol in the box below represents a mole of a component in one liter of a buffer solution; represents the anion (X-), = the weak acid (HX), = H+, and =OH. Water molecules and the few H+ and OH- ions from the dissociation of HX and X- are not shown. The box contains 10 mol of a weak acid, , in a liter of solution. Show what happens upon (a) the addition of 2 mol of OH- (2 ). (b) the addition of 5 mol of OH- (5 ). (c) the addition of 10 mol of OH- (10 ). (d) the addition of 12 mol of OH- (12 ). Which addition (a)-(d) represents neutralization halfway to the equivalence point?
A bottle of concentrated hydroiodic acid is 57% HI by weight and has a density of 1.70 g/mL. A solution of this strong and corrosive acid is made by adding exactly 10.0 mL to some water and diluting to 250.0 mL. If the information on the label is correct, what volume of 0.988 M NaOH is needed to neutralize the HI solution? Suggest an indicator for the titration.
You are given the following acidbase titration data, where each point on the graph represents the pH after adding a given volume of titrant (the substance being added during the titration). a What substance is being titrated, a strong acid, strong base, weak acid, or weak base? b What is the pH at the equivalence point of the tiration? c What indicator might you use to perform this titration? Explain.
A student intends to titrate a solution of a weak monoprotic acid with a sodium hydroxide solution but reverses the two solutions and places the weak acid solution in the buret. After 23.75 mL of the weak acid solution has been added to 50.0 mL of the 0.100 M NaOH solution, the pH of the resulting solution is 10.50. Calculate the original concentration of the solution of weak acid.
Enough water is added to the buffer in Question 30 to make the total volume 5.00 L. (a) Calculate the pH of the buffer. (b) Calculate the pH of the buffer after adding 0.0250 mol of HCl to 0.376 L of the buffer. (c) Calculate the pH of the buffer after adding 0.0250 mol of KOH to 0.376 L of the buffer. (d) Compare your answers to Question 30 (a-c) with your answers to (a-c) of this problem. (e) Comment on the effect of dilution on the pH of a buffer and on its buffer capacity. Â
Sketch the titration curve for a weak acid titrated by a strong base. When performing calculations concerning weak acidstrong base titrations, the general two-slep procedure is to solve a stoichiometry problem first, then to solve an equilibrium problem to determine the pH. What reaction takes place in the stoichiometry part of the problem? What is assumed about this reaction? At the various points in your titration curve, list the major species present after the strong base (NaOH, for example) reacts to completion with the weak acid, HA. What equilibrium problem would you solve at the various points in your titration curve to calculate the pH? Why is pH 7.0 at the equivalence point of a weak acid-strong base titration? Does the pH at the halfway point to equivalence have to be less than 7.0? What does the pH at the halfway point equal? Compare and contrast the titration curves for a strong acidstrong base titration and a weak acidstrong base titration.
Another way to treat data from a pH titration is to graph the absolute value of the change in pH per change in milliliters added versus milliliters added (pH/mL versus mL added). Make this graph using your results from Exercise 61. What advantage might this method have over the traditional method for treating titration data?
8-71 Explain why you do not need to know the chemical formula of a buffer compound to use it.
Explain why barium fluoride dissolves in dilute hydrochloric acid but is insoluble in water.
A quantity of 0.15 M hydrochloric acid is added to a solution containing 0.10 mol of sodium acetate. Some of the sodium acetate is converted to acetic acid, resulting in a final volume of 650 mL of solution. The pH of the final solution is 4.56. a What is the molar concentration of the acetic acid? b How many milliliters of hydrochloric acid were added to the original solution? c What was the original concentration of the sodium acetate?
A friend asks the following: Consider a buffered solution made up of the weak acid HA and its salt NaA. If a strong base like NaOH is added, the HA reacts with the OH to form A. Thus the amount of acid (HA) is decreased, and the amount of base (A) is increased. Analogously, adding HCI to the buffered solution forms more of the acid (HA) by reacting with the base (A). Thus how can we claim that a buffered solution resists changes in the pH of the solution? How would you explain buffering to this friend?