Q2:A stepping motor has 200 step angles. Its output shaft is directly coupled toleadscrew with pitch = 0.25 in/rev. A worktable of a machine tool is driven by theleadscrew. The table must move a distance of 5 in from its present position at a travelspeed of 20 in/min. Determine (a) the number of pulses required to move the tablethe specified distance and (b) the required motor speed and pulse rate to achieve thespecified table speed.

Answered: Image /qna-images/answer/20d088ca-2971-4414-807e-5021d5268a73.jpg

Answered: A stepping motor has 200 step angles.…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A NC machine tool table is powered by a servomotor, lead screw, and optical encoder. The lead screw has a pitch = 5.0 mm and is connected to the motor shaft with a gear ratio of 16:1 (16 turns of the motor for each turn of the lead screw). The optical encoder is connected directly to the lead screw and generates 200 pulses/rev of the lead screw. The table must move a distance = 100 mm at a feed rate = 500 mm/min. Determine (a) the pulse count received by the control system to verify that the table has moved exactly 100 mm; and (b) the pulse rate and (c) motor speed that correspond to the feed rate of 500 mm/min. Solve the problem assuming the optical encoder is directly coupled to the motor shaft rather than to the lead screw.
The drive unit for a positioning table is driven by a leadscrew directly coupled to the output shaft of a stepping motor. The pitch of the leadscrew = 0.18 in/rev. The table must have a linear speed = 35 in/min. If the relationship between leadscrew pitch p and number of step angles n, is as follows: ns-1250p/rg, determine (a) the minimum number of step angles (pulse/rev) in the stepping motor to achieve the required accuracy, (b) the associated step angle, and (c) the frequency of the pulse train required to drive the table at the desired speed.
Calculate the mobility of the kinematic chain please
A stepping motor with 240 step angles is coupled to a leadscrew through a gear reduction of 5:1 (5 rotations of the motor for each rotation of the leadscrew). The leadscrew has 6 threads/in. The worktable driven by the leadscrew must move a distance = 10.00 in at a feed rate of 30.0 in/min. Determine: Number of pulses required to move the table, and The required motor speed and pulse rate to achieve the desired table speed.
Crack AB of a slider crack mechanism shown in Figure 2 rotate at a constant speed of 300 rpm in clockwise direction. The connecting rod BC has a length of 1 m and incline at 45° to vertically positioned piston C. B 1 m 0.2 m 45 Figure 2: Slider crank mechanism 3.1. Draw the displacement diagram of the mechanism shown in Figure 2 to scale. Use a vector diagram to determine the velocity of the piston C and connecting 3.2. rod BC. 3.3. Calculate the acceleration of piston C and the angular acceleration of connecting rod BC.
the figure shows a motor driving a two-output transmission system. The blower requires a certain amount of force to operate since the drum rotates at an angular acceleration of 0.03 rad/s2. Determine the torque produced by a motor with a torque of 700 Nm and a speed of 1,600 rpm. following:- The power produced at the drum (P). The torque requirement for the blower to operate (Tblower) and power generation (Pblower) The overall efficiency transmission of the gear system, hO. If the speed of motor is NOT given, explain without calculation how the overall efficiency transmission of the gear system can be obtained. Given:- Number of gear teeth, t:- t1=40 ; t2=200 ; t3=50 ; t4=200 ; t5=40 ; t6=120 ; t7=60 and t8=120 Equivalent mass moment of inertia, Ieq:- Imotor,5=25 kgm2 ; I23=10 kgm2 ; Iblower,4=15 kgm2 ; I67=20 kgm2 and Idrum,8=60 kgm2 Friction torque in bearing, Fb:- A=F=25 Nm ; I=J =20 Nm ; B=C=G=H=5 Nm and D=E=10 Nm Efficiency of all gear mesh, ⴄ=85%
Question 3: Crack AB of a slider crack mechanism shown in Figure 2 rotate at a constant speed of 300 rpm in clockwise direction. The connecting rod BC has a length of 1 m and incline at 45° to vertically positioned piston C. B 1 m 0.2 m 45 Figure 2: Slider crank mechanism 3.1. Draw the displacement diagram of the mechanism shown in Figure 2 to scale. 3.2. Use a vector diagram to determine the velocity of the piston C and connecting rod BC. 3.3. Calculate the acceleration of piston C and the angular acceleration of connecting rod BC.
Create a displacement diagram with the following details: Maximum displacement of 60 mm 60 mm rise from 0 degree to 45 degree using simple harmonic motion 60 mm fall from 45 degree to 90 degree using simple harmonic motion Dwell from 90 degree to 120 degree 60 mm rise from 120 degree to 210 degree using uniform acceleration and retardation motion Dwell 60 degrees Return stroke using cycloidal motion Other notes: Use 3 degree = 2 mm ratio Label the displacement diagram for every 30 degrees (20mm) in the x-axis Provide computations if needed (specially in creating cycloidal motion)
For the following mechanism, determine: 1) Number of degrees of freedom 2) Displacement of slider E when link 2 rotates 45 degrees CW 3) Displacement angle of link 4 10.1" 4.9" 3.3" .8" (3 Be D 3" 2 3.2" 90° 5.3"
Write the difference between linear and angular impulse.
Question 3: Mechanisms [16]The lengths of various links of a mechanism, as shown in Figure 2, are:OA = 0.3 m; AB = 1 m; CD = 0.8 m; and AC = CB. SKETCH BELOW 3.1. Draw the displacemt diagram to a scale. 3.2. Determine the velocity of piston B if the crank OA rotates at 160 r.p.m in theclockwise direction.3.3. Calculate the velocity of point C.
Evaluate the 3-DOF wrist as shown in Figure 2, use the conventional method to determine 1. Linear velocity and 2. Angular velocity NOTE: for JOINT 3 ( 03 ) only Connected to robot arm Pitch Roll Yaw Figure 2: Wrist assembly The known position and orientation of the end of the arm point is. C, C2 [-C,S2C3 + S¼S3 -S;S2C3 – C1S3 C2C3 C¡S2S3 + S1C3 S4S2S3 + C,C3 -C2S3 01 S,C2 S2 1 °T3=°T¡'T2²T3

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS