A steel pipe column resting on a steel base plate concrete pedestal supports an axial load of P = 1200KN, as shown. The column has an unbraced length of 3.5m, outside diameter of D = 280mm and can be assumed hinged at both ends. The allowable compressive strength of column is 60MPA and the allowable bearing strength of concrete is 9.6MPA. P it L d D D, Base plate Concrete pedestal

A steel pipe column resting on a steel base plate concrete pedestal supports an axial load of P = 1200KN, as shown. The column has an unbraced length of 3.5m, outside diameter of D = 280mm and can be assumed hinged at both ends. The allowable compressive strength of column is 60MPA and the allowable bearing strength of concrete is 9.6MPA. P it L d D D, Base plate Concrete pedestal

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter9: Composite Construction

Section: Chapter Questions

Problem 9.1.2P

See similar textbooks

Similar questions

A rectangular beam 250 mm wide, 500 mm deep is reinforced at the bottom with d-20-mm-dismeter bars and at the top with 2-16-mm bars. Concrete cover to bar centroid at the top is M0 mm and at the bottom is 70 mm. Use concrete strength r'e-21 MPa und steel yield strength fy 415 MPa for 20- mm bars and fy= 275 MPA for 16 mm bars Detenmine the design moment capacity n kN m of the beam in negative bending. A 40.06 O45.07 C. 42.70 D47.55
Exercises 1- A rectangular beam reinforced with 4 o18 bars has h=650mm, bw=250mm and d'=30mm. Applied moment is 67 kN.mMaterials used are C25 and S220. Allowable compressive stress and modulus of rupture for concrete are 10MPA and 2.3 N/mm2 respectively. Allowable stress for steel is 140 MPa. Is this beam cracked or uncracked? Is this beam designed adequately to carry the applied moment safely? 2- Does this beam have enough capacity to carry the applied moment? Also, calculate the position of neutral axis. h=50cm, bw= 25 cm, and d'=3cm. C25 and S420 are used. (kı= 0.85; fod= 17 MPa; fya=365 MPa; E= 2X10°N/mm?) DL= 30 kN/m LL= 15 kN/m 4Ф 22 5.3 m 3- Calculate the moment carrying capacity of the beam shown? Choose the required steel reinforcement to carry this moment. d=470mm b= 270mm and d'=30mm. C20: Allowable stress=7MPA S420: Allowable stress=220 MPa A, n=15
an exterior beam has 300 mm and a height of 600 mm, it is reinforced with 5-p25 mm bars for tension which is laid out according to the code requirements. the depth of the tension strain of the beam is 353 mm. of the steel has a yield strength of 414 mpa. determine the following: Compressive strength of the concrete Maximum steel ratio Ultimate moment capacity of the beam
Design a base plate of A36 steel (Fy = 36 ksi) for a W12 x 65 column (Fy = 50 ksi) that supports the loads PD = 200 k and PL = 300 k. The concrete has a compressive strength f'c=3 ksi, and the footing has the dimensions 9 ft x 9 ft.
3. A reinforced rectangular concrete beam having a width of 300 mm, effective depth of500 mm, fc’ = 24 MPa, fy = 415 MPa, 4 - 28 mmɸ, d’ = 65 mm. Present the following (a) actual steel ratio (b) maximum steel ratio (c) a(d) c (e) check if steel yields (f) ?steel(g) type of failure (h) reduction factor (i) moment capacity
3) A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.2 m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-∅25 mm bars in two rows with 25 mm vertical clear spacing. Use material strengths f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = ___________ Depth of uniform stress block at ultimate stage in mm to the nearest whole number = ___________ Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places = __________
A rectangular beam has a width of 258mm and an effective depth of 600mm. It is reinforced with 4-36mm bars. The compressive strength of the concrete is 28MPa and the yield strength of the steel is 279MPa. The depth of the concrete stress block is ___ mm.
Design the Beam AB Below by using Working Stress Method; A 4.3 kN/m 3.2 m Dead Load, D.L=7 kN/m Live Load, L.L = 4.3 kN/m The allowable compressive stress of the concrete, fc 13 N/mm² Allowable tensile stress in steel, fs = 160 N/mm2 Modulus of elasticity of steel, Es 210000 Mpa Modulus of elasticity of Concrete, Ec = 22000 Mpa Beam Width, b= 200 mm
The concrete post is reinforced axially with four symmetrically placed steel bars, each of cross-sectional area 900 mm2. Compute the stress in each material when the 1000-kN axial load is applied. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. Compatibiltiy Equation . Ust Bearing |1000 kN plate Steel- Concrete 300 mm 300 mm Section a-a
ス F. reinforced concete structure is shown The floor framing plan oF in the figure. The beams are 280 mm wide and S20 mm deep, and the slob is 110mm thick an edditional (super impes) veight,1 and live lo ad of OTher than conerete weight, the floor subjected other to Is dead load of 3k Pa si2 k Por. Unit weight of concrete is 23.5 kN/m® le Determine the total uniform load on beam DEF and ABC axial load 20 Determme the total on columns A and B,D an) E 2Sm 티 2.Sm 6.2m 6.2m
a concrete floor slab 100mm thick is cast monotholic with concrete beams 2.0 m on centers. the beams have a span of 4.0m, web width of 259 mm and overall depth of 50 mm. the tensile reinforcement consists of 6-⌀20 mm bars in two rows with 25mm vertical clear spacing. use material strengths f'c=21MPa and fy=415MPa. calculate the ff considering a T-geometry: 1. effective flange width of an interior beam in mm 2. depth of uniform stress block at ultimate stage in mm to the nearest whole number 3. tensile steel strain compatible strain of 0.003
1.2m 10 cm O 7cm -7cm O This concrete beam has four A-35 steel rods of one centimeter diameter and a square cross section. It experiences a compressive axial load of 200kN. You must calculate the stresses developed in the two components in the figure.