A steam turbine takes in steam at the rate of6000 kg/h and its power output is 800 kw.neglect any heat loss from the turbine. Findthe change in the specific enthalpy of thesteam as it passes through the turbine if (a)the entrance and exit are at the sameelevation and the entrance and exit velocitiesare negligible or (b) the entrance velocity is 50m/s and the exit velocity is 200 m/s, with theoutlet pipe 2.0 m above the inlet.

Answered: Image /qna-images/answer/243d43fe-0213-4898-9b38-784144ff166d.jpg

Answered: A steam turbine takes in steam at the…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A saturated steam at 400kPa enters the turbine and exits as saturated liquid at 80o C flowing at 0.2m/s. If both inlet and outlet pipes have a diameter of 12.5cm, calculate the work produced in the operation. Perform Degree of Freedom analysis.
Steam enters a turbine with a mass flow rate of 4600 kg/h. Enthalpies at the intlst and exhaust are 3177.2 kJ/kg and 2345 kJ/kg respectively. If there is a heat loss of 63kW. Determine the next work output of the turbine (Please solve step by steps solution Thank you!)
Argon enters a turbine ayt 900 kPa and 450 0C at a rate of 2.90 kg/s and leaves at 150 kPa and 270 0C. What is the power output of this turbine in kW?
A nozzle is a device for measuring the velocity of flow. At inlet to a nozzle the enthalpy is 3026 kJ/k, the velocity is 60 m/s. At exit from the nozzle the enthalpy is 2790 kJ/kg. The nozzle is horizontal and there is a negligible heat loss from the nozzle. Find he velocity at nozzle exit The inlet area is 0.1 m2 and the specific volume at the inlet is 0.19 m²/s, find the mass flow rate • f the specific volume at the nozzle exit is 0.5 m²/kg, find the exit area of the nozzle (688m/s) (0.36kg/s) (0.0299m2) Air and fuel enter a furnace used for home heating. The air has an enthalpy of 320 kJ/kg and the fuel has an enthalpy of 43027 kJ/kg. The gases leaving the furnace has an enthalpy of 616 kJ/kg. There are 17 kgair / kgfuel, water circulated through the wall furnace receiving heat. The hose required 17.02 kW of heat, what is the fuel consumption per day. (41 kg/day)
During the execution of a reversible non-flow process the work is -156.2 KJ if V₁=0.845 and the pressure varies as P--730 V +690 KPa, where volume V is in m³. Find the final volume.
piston cylinder contains 1 kg water at 20oC with a constant load on the piston such that the pressure is 250 kPa. A nozzle in a line to the cylinder is opened to enable a flow to the outside atmosphere at 100 kPa. The process continues to half the mass has flowed out and there is no heat transfer. Assume constant water temperature. Show that V2=V1/2 and find the exit velocity and total work done in the process.
Pressure remains constant at 689.5 kPa while the volume changes from 0.567 m3 to 0.283 m3. Find the following: Heat in kJ/kgm Change in entropy in kJ/kgm-K Work non-flow in kJ/kgm
During the execution of a reversible non-flow process the work is -156.2 KJ if V1=0.845 andthe pressure varies as P=-730 V +690 KPa, where volume V is in m3. Find V2
A pump increases the water pressure from 70 kPa at the inlet to 700 kPa at the outlet. Water enters this pump at 45 oC through a 1.5 cm diameter opening and exits through a 2.1 cm diameter opening. Determine the velocity of the water at the (a) inlet and (b) outlet when the mass flow rate through the pump is 1.4 kg/s. Submit your solution by multiplying (a)*(b) = Format answer : 46.84 Submit
At a flow rate of .5000 m3 / h, saturated air at a temperature of 2 ° C is heated sensibly up to a temperature of 40 ° C with the help of a heating coil. Find the amount of heat that should be given to the coil.
(a) A garden hose attached with a nozzle is used to fill a 20-gallon bucket. The inner diameter of the hose is 2 cm, and it reduces to 0.8 cm at the nozzle exit. If it takes 55 s to fill the bucket with water, determine the volume and mass flow rates of water through the hose, and the average velocity of water at the nozzle exit. Comment on the result.
Refrigerant R-134a to the compressor of a refrigeration machine It enters at 140 kPa pressure and -10 °C, and exits at 1 MPa pressure. Volumetric flow of the refrigerant entering the compressor It is 0.23 m³/minute. The refrigerant enters the throttling valve at a pressure of 0.95 MPa and at 30 °C, and exits the evaporator as saturated steam at -18 °C. Adiabatic efficiency of the compressor It is 78%. Show the cycle in the T-s diagram. And; a) Calculate the power required to run the compressor. b) Calculate the heat absorbed per unit time from the cooled medium. ( COPSM=? ) c) Calculate, between the evaporator and the compressor, how much the pressure of the refrigerant drops and how much the heat gain.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS