A steam is flowing through a 5.7 m long of steel tube that has inner and outer radii of r, = 0.015 and r, 0,024 m, and a thermal conductivity of 0.14 W/m.K. The steam and the outer surface of the tube is maintained at constant temperature of 150 °C and the air = 25 °C, h = 0.35 W/m2.k) is surrounding the tube. To prevent the outer surface of the steel from the environmental conditions, a material that has a thermal conductivity of 0.014 W/m.k is wrapped over the outer surface of the steel. What is the maximum heat transfer from the steam to the air (W)? NOTE: Enter your answer. Answer Air Th Steam Steel Tr 111 To

A steam is flowing through a 5.7 m long of steel tube that has inner and outer radii of r, = 0.015 and r, 0,024 m, and a thermal conductivity of 0.14 W/m.K. The steam and the outer surface of the tube is maintained at constant temperature of 150 °C and the air = 25 °C, h = 0.35 W/m2.k) is surrounding the tube. To prevent the outer surface of the steel from the environmental conditions, a material that has a thermal conductivity of 0.014 W/m.k is wrapped over the outer surface of the steel. What is the maximum heat transfer from the steam to the air (W)? NOTE: Enter your answer. Answer Air Th Steam Steel Tr 111 To

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter7: Forced Convection Inside Tubes And Ducts

Section: Chapter Questions

Problem 7.4P

See similar textbooks

Similar questions

7.43 Liquid sodium is to be heated from 500 K to 600 K by passing it at a flow rate of 5.0 kg/s through a 5-cmID tube whose surface is maintained at 620 K. What length of tube is required?
Determine the rate of heat transfer per meter length to a light oil flowing through a 2.5-cm-ID, 60-cm-long copper tube at a velocity of 0.03 m/s. The oil enters the tube at 16C, and the tube is heated by steam condensing on its outer surface at atmospheric pressure with a heat transfer coefficient of 11.3 kW/m K. The properties of the oil at various temperatures are listed in the following table: Temperature, T(C) 15 30 40 65 100 (kg/m3) 912 912 896 880 864 c(kJ/kgK) 1.80 1.84 1.925 2.0 2.135 k(W/mK) 0.133 0.133 0.131 0.129 0.128 (kg/ms) 0.089 0.0414 0.023 0.00786 0.0033 Pr 1204 573 338 122 55
A mild-steel cylindrical billet 25 cm in diameter is to be raised to a minimum temperature of 760C by passing it through a 6-m long strip-type furnace. If the furnace gases are at 1538C and the overall heat transfer coefficient on the outside of the billet is 68W/m2K, determine the maximum speed at which a continuous billet entering at 204C can travel through the furnace.
Example: 0.5 kg of water per minute is heated from 20° to 40°C when passed through a tube of 2.5 cm diameter steel pipe. The pipe surface temperature is maintained at 110°C by condensing steam on its surface. Find out the length of the pipe required. The properties of water at mean temperature of 70°C are given below: p = 978 kg/m² k= 0.575 W/m. K Cp = 4200 J/kg. K v = 0.415 x 10-6 m²/sec
High-pressure steam condenses at 400 K on the outer surface of a thin-walled tube of 50 mm diameter. The overall heat transfer coefficient between steam and air on the inside of the tube is 200 W/m?. If the air enters the tube at 25 m/s, 150 kPa and 280 K, find the length of the tube required for the air to be heated to 350 K.
Heat Transfer (Third year) 2020- 2021 Homework 01-03-2021 By Dr. Basil Noori Merzah one-dimensional heat transfer and disregarding radiation, determine the rate of heat transfer through the wall. Q4/ Steam at T01-320°C flows in a cast iron pipe (k=80W/m. C) whose inner and outer diameters are D,=5cm, and D,-5.5cm, respectively. The pipe is covered with 3 cm thick glass wool insulation with k=0.05W/m. C. Heat is lost to the surroundings at T2-5°C by natural convection and radiation, with a combined heat transfer coefficient to be h,=18W/m."C. Taking the heat transfer coefficient inside the pipe to be 2 0 h,-60W/m. C, determine the rate of heat loss from the steam per unit length of the pipe. Also determine the temperature drops across the pipe shell and the insulation. Q5/ Determine the overall heat transfer coefficient U based on the outer surface of a D=2.5cm, and D =3.34 cm steel pipe (k=54.0W/m. C) for the following conditions: inside and outside heat transfer coefficients are…
A long 3-mm diameter rod of steel (ρ = 7840 kg/m3, c = 460 J/kgK, k = 43 W/mK)has a uniform initial temperature of 650C. The rod is then suddenly immersed in alarge container of 25C water. The hot rod causes the water immediately surroundingthe rod to boil, giving rise to a heat transfer coefficient of 5600 W/m2K. The boilingstops when the rod reaches a temperature of 100C, at which time the heat transfercoefficient becomes 750 W/m2K. Find the time period during which boiling occursand the total time required for the rod to reach a temperature of 40C. Use acharacteristic length for this problem.
A pipe 30 m long with an outer diameter of 75 mm is used to deliver steam at a rate of 2000 kg / hour. The vapor pressure is 198.53 kPa entering the pipe with a quality of 98%. The pipe needs to be insulated with a thermal conductivity of 0.2 W / (m K) so that the quality of the steam will only slightly decrease to 95%. The outer surface temperature of the insulation is assumed to be 25 ° C. Ignore resistance conductive of the pipe material and it is assumed that there is no pressure drop in the pipe. a. Determine the enthalpy of incoming vapor = AnswerkJ / kg. b. Determine the enthalpy of steam coming out = AnswerkJ / kg. c. Determine the vapor heat change / loss along the flow = Answerwatt. d. Specify the minimum required insulation thickness = Answercm.
A pipe 30 m long with an outer diameter of 75 mm is used to deliver steam at a rate of 1500 kg / hour. The vapor pressure is 198.53 kPa entering the pipe with a quality of 98%. The pipe needs to be insulated with a thermal conductivity of 0.2 W / (m K) so that the quality of the steam will only slightly decrease to 95%. The outer surface temperature of the insulation is assumed to be 25 ° C. Ignore resistance conductive of the pipe material and it is assumed that there is no pressure drop in the pipe. a. Determine the enthalpy of incoming vapor = Answer kJ / kg. b. Determine the enthalpy of steam coming out = Answer kJ / kg. c. Determine the vapor heat change / loss along the flow = Answer watt. d. Specify the minimum required insulation thickness = Answer cm.
Heat Transfer with a Liquid Metal. The liquid metal bismuth at a flow rate of 2.00 kg/s enters a tube having an inside diameter of 35 mm at 425°C and is heated to 430°C in the tube. The tube wall is maintained at a temperature of 25°C above the liquid bulk temperature. Calculate the tube length required. The physical properties are as follows (H1): k = 15.6 W/m K, c,=149 J/kg K, u = 1.34 x 10-3 Pa s.
A pipe 30 m long with an outer diameter of 75 mm is used to carry steam at a rate of 1000 kg / hour. The vapor pressure is 198.53 kPa entering the pipe with a quality of 98%. The pipe needs to be insulated with a thermal conductivity of 0.2 W / (m K) so that the quality of the steam will only slightly decrease to 95%. The outer surface temperature of the insulation is assumed to be 25 ° C. Ignore resistance conductive of the pipe material and it is assumed that there is no pressure drop in the pipe. a. Determine the enthalpy of incoming vapor = Answer kJ / kg. b. Determine the enthalpy of steam coming out = Answer kJ / kg. c. Determine the vapor heat change / loss along the flow = Answer watt. d. Specify the minimum required insulation thickness = Answer cm.
Steam at 350 °C flows through the stainless steel pipe with k=26 W/m.°C. The inner and outer diameters of the stainless steel pipe are 6.0 cm and 7.0 cm, respectively. The pipe is insulated from the outside with a 4.0 cm thick glass wool (k= 0.038 W/m.°C) and then a 3.0 cm thick k=0.25 W/m.K material. The insulated pipe is in the environment at 20 °C. The heat loss from the pipe occurs only by [natural convection+radiation]. Film heat transfer coefficient including the effects of [natural convection+radiation] in the insulated pipe is 30 W/m². is C. Calculate the heat transferred per unit pipe length since the film heat transfer coefficient defined according to the inner area of the pipe is 110 W/m².°C.