A spring-loaded piston-cylinder device contains 0.21 kg of water initially at 90°C and with an initial quality of 17.8%. At its initial state, the spring is relaxed and does not exert any force on the piston. The device is now heated until the pressure is 400 kPa and the new temperature is 250°C. What is the boundary work done by the water during this process? KJ What is the total amount of heat transfer into the system? KJ If the device has a cross-sectional area of 0.08 m², what is the spring constant of the spring in this device? kN m

A spring-loaded piston-cylinder device contains 0.21 kg of water initially at 90°C and with an initial quality of 17.8%. At its initial state, the spring is relaxed and does not exert any force on the piston. The device is now heated until the pressure is 400 kPa and the new temperature is 250°C. What is the boundary work done by the water during this process? KJ What is the total amount of heat transfer into the system? KJ If the device has a cross-sectional area of 0.08 m², what is the spring constant of the spring in this device? kN m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3- A frictionless piston cylinder device initially contains 200 L of saturated vapor refrigerant R-12 at 800 kPa. The refrigerant R-12 is now heated until its temperature becomes 50 C. Find: (1) the mass of R-12, (2) Au, Ah & Av, (3) the work done during this process, (4) the amount of heat added to the system, and (5) show the process on T-v diagram
5- During some actual expansion and compression processes in piston cylinder device, the gases have been observed to satisfy the relationship Py" = const.. Calculate: (1) the work done when a gas expands from a state 150 kPa and 0.03 m' to a final volume of 0.2 m for (n=1.3), and (2) show the process on P-V diagram
2- A mass of 5 kg of saturated liquid water at 200 kPa is heated at a constant pressure until the temperature reaches 300°C. Find: (1) Au, Ah & Av, (2) the work done during this process, (3) the amount of heat added to the system, and (4) show the process on T-v diagram
A piston-cylinder arrangement contains air at pressure of 1 MPa and expands according to a process represented by a straight line on p-V diagram. The final pressure is 0.1 MPa. Calculate the work done by the air if the stroke is 0.2 m and the diameter of the piston is 0.4 m?
Steam at a pressure of 11 bar and a temperature of 320C is containedin a large vessel. Connected to the vessel through a valve is a turbinefollowed by a small initially evacuated tank with a volume of 0.60 m3.When emergency power is required, the valve is opened and the tankfills with steam until the pressure is 11 bar. The temperature in the tankis then 400C. The filling process takes place adiabatically and kineticand potential energy effects are negligible. Determine the amount ofwork developed by the turbine in kJ.
PLEASE SHOW COMPLETE SOLUTION THANK U 1. A rigid vessel contains 5kg of wet steam (water) at 0.4 MPa. After the addition of 9585 kJ of heat, the steam has a pressure of 2.0 MPa and a temperature of 7000C Determine (a) the initial quality, (b) internal energy, and (c) specific volume of the steam.
A rigid tank contains air at 500 kPa and 150°C. As a result of heat transfer to. the surroundings, the temperature and pressure inside the tank drop to 65°C and * ?400 kPa, respectively. the boundary work done during the process is positive negative zero non of the above
Water with a quality of 53.5% and pressure of 200 kPa is inside a rigid tank.The tank is heated by an electric heater rated as 120 W for 8 minutes until the temperature reaches 250 Celcius. Find Final temperature of the tank?
Consider a closed piston cylinder that contains 0.2 kg of superheated water vapor at 200C and 100kPa. The cylinder is cooled and the piston moves is such a way that the pressure remains constant. At the end of the cooling process the water in the cylinder is a compressed liquid at 20C and 100kPa. Calculate the initial volume of the cylinder. Calculate the final volume of the cylinder. Calculate the work done on the system during the cooling process. How much heat was trasferred from the system to the surrounding area during the cooling process?
A 1.5m diameter spherical balloon containing air at (162 + 10) kPa is cooled such that the volume is reduced by 25%. For the process, the pressure is proportional to the square of the sphere’s diameter. What is the work done by the surrounding?
A 110-volt 6 Ampere electric heatrer is submerged in 1 kg of water for 24 minutes. What will be the final temperature of the water if its initial temperature is 23 C. Assume a heat loss of 13%.
The temperature before and after the adiabatic process is 200 K and 127°C. The pressure before the process is 500000 N/cm² and adiabatic index is 2.4, then its pressure after the process is approximately 4000000 N/cm2 Seloct ono