A solid steel shaft with a diameter of 130 mm must be press-fitted in a journal bearing (Figure 1)with an inlet and outlet diameters of 130 and 145 mm, respectively. Both solid shaft and journalbearing require rigidity and alignment with an accuracy of the location. Consider a journal bearinginlet diameter as the basic size.OudetBearingInletJournalFigure 1 AJournal Bearing 1.1 State the two applicable standards when determining the fits for holes and shafts.Determine the following:1.2 the tolerance class, ISO code, and the nominal diameter that can be used,1.3 the tolerance limits for both the solid steel shaft diameter and the journal bearing inletdiameter, and1.4 the dimensions of both the solid steel shaft diameter and the journal bearing inletdiameter.

Answered: Image /qna-images/answer/1ef465fa-a07b-46f4-8b8d-b86ebd59b203.jpg

A solid steel shaft with a diameter of 130 mm must be press-fitted in a journal bearing (Figure 1) with an inlet and outlet diameters of 130 and 145 mm, respectively. Both solid shaft and journal bearing require rigidity and alignment with an accuracy of the location. Consider a journal bearing inlet diameter as the basic size. Outet Bearing Jeumal Figure 1 AJournal Bearing

A solid steel shaft with a diameter of 130 mm must be press-fitted in a journal bearing (Figure 1) with an inlet and outlet diameters of 130 and 145 mm, respectively. Both solid shaft and journal bearing require rigidity and alignment with an accuracy of the location. Consider a journal bearing inlet diameter as the basic size. Outet Bearing Jeumal Figure 1 AJournal Bearing

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Figure below shows a rotating shaft simply supported in ball bearings at A and D and loaded by a nonrotating orce Fof 6.8 kN. Using ASTM "minimum" strengths, estimate the life of the part. 6T td7 (a) Shaft drawing showing all dimensions in millimeters; all fillets 3-mm radius. The shaft rotates and the load is stationary; material is machined from AISI 1050 cold-drawn steel. (b) Bending moment diagram.
A collar is fitted as a tight fit on a solid shaft. made before assembly in measuring, the outer diameter of the ring is dga=159.97 mm, the inner diameter is dgi= 100.03 mm, the outer diameter of the shaft is dma= 100.048 mm. After assembly; a. What is the surface pressure between the shaft and the ring? b. What is the maximum shear stress? Given: Material pair steel/steel E=2.1x105 N/mm2 , Tmax = P (1/QG^2)
campute the bending stress number for the goer pair described by the given data beLow. KS= 1, Km= 1,21, F= 2.00 in, DP= 3,33 in, NG= 70, Np=20 hp = 1750v. p.m, Av=11, Pd =6, Tp= 900ib V1= 1527 ft/min The matarial used for pinion a gear is cast iron
The design load on a ball bearing is 413 lbf and an application factor of 1.2 is appro- priate. The speed of the shaft is to be 300 rev/min, the life to be 30 kh with a reliability of 0.99. What is the C10 catalog entry to be sought (or exceeded) when searching for a deep-groove bearing in a manufacturer's catalog on the basis of 106 revolutions for rat- ing life? The Weibull parameters are xo = 0.02, (0 – xo) = 4.439, and b = 1.483. %3D
d = 1.25 inch speed 2200 rpm 12000 Ibf d. Shaft load = 2000 lbf (centered between bearings) Temperature: 170 F Tr Bearing specs: O, = 25 Length ratio= 0.80 clearance ratio: Cd -0.002 2. Hydrodynamic bearings are to be selected for the design shown above. Find the following: eccentricity ratio e eccentricity e in., hmin in., Pavs. Ibf/in, Torsional resistance T, in-lbf, Viscosity n microreyn, Oil type: SAE , power loss o HP
Q.6 Calculate the bearing life , if rating life for bearings is 9000h and shaft is rotating at 1500rpm. A 850 million rev В 810 million rev 810 h D 850h
Q.6 Calculate the bearing life , if rating life for bearings is 9000h and shaft is rotating at 1500rpm. A 850 million rev B 810 million rev C 810 h D 850h
Answer this ASAP plz A double row angular contact ball bearing is used in the engine compressor to accept radial loads of 6000 N and axial loads of 3000 N, operating at 2400 rpm for an average life of 7 years at 8 hours per day. Assume that the shock load is light. Select the appropriate bearing number. Note: the equivalent dynamic load is the dynamic equivalent radial load times the service factor.
Mechanical design A shaft with the following data: 1- The pulley (A) is 1000 mm in diameter and weight 300N. 2- The gear (B) pitch diameter is 600mm and weight -250N. 3- The pulley is keyed to the shaft at 400mm to the left of left hand bearing. 4-the distance between bearing C and B is 1250 mm. 5- The power is 20 kW at 750 rpm. 6- Tension ratio T1 / T2-2.5 7- The shaft d.livers power to a gear placed horizontally in front, the pressure angel of gear is 20. 8- The allowable shear stress is 70N / mm, kt-2 and km- 1.5. Determine: the diameter of shaft
A short stub shaft, made of SAE 1035, as rolled, receivers 30 hp at 300 rpm via a 12-in. spur gear, the power being delivered to another shaft through a flexible coupling. The gear is keyed (profile keyway) midway between the bearings. The pressure angle of the gear teeth   20o, N = 1.5 based on the octahedral shear stress theory with varying stresses. (a) Neglecting the radial component R of the tooth load W , determine the shaft diameter. (b) Considering both the tangential and the radial components, compute the shaft diameters. (c) Is the difference in the results of the parts (a) and (b) enough to change your choice of the shaft size?
(8) An axle (non-rotating) is to be machined from AISI 1144, OQT 1,000°F, to the proportions keyway в shown, with a fillet radius r = 0.2D; F varies 1.SD from 400 lb. to 1,200 lb.; the supports are to the left of B, not shown. Let N = 2 (Soderberg Line). 6" (a) At the fillet, compute D and the 30 maximum tensile stress. (b) Compute D at section B. (c) Specify suitable dimensions. Keeping the given proportions, would a smaller diameter be permissible if the fillet were shot-peened?
Thory of machine: Select one of the following bearing for the load conditions. Radial load, F=3000 N, Axial load, F = 1600 N, RPM = 1000. (1) Deep Groove ball bearing dynamic load rating=47000 N radial bad factor, X=0.56 Axial load factor, Y= 1.83 (i) Cylindrical roller bearing Dynamic load rating 28000 N radial load factor, X=1.0 axial load factor, Y=0.0