A solið, homogeneous sphere with a mass of mo, a radius of ro and a density of po is placed in a container of water. Initially the sphere floats and the water level is marked on the side of the container. What happens to the water level, when the original sphere is replaced with a new sphere which has different physical parameters? Notation: r means the water level rises in the container, f means falls, s means stays the same. Combination answers like 'f or s' are possible answers in some of the cases. - The new sphere has a radius of r = ro and a density of p< Po- - The new sphere has a density of p > Po and a mass of m = mo. - The new sphere has a radius of r = ro and a mass of m < mo- Submit Answer Tries 0/12

A solið, homogeneous sphere with a mass of mo, a radius of ro and a density of po is placed in a container of water. Initially the sphere floats and the water level is marked on the side of the container. What happens to the water level, when the original sphere is replaced with a new sphere which has different physical parameters? Notation: r means the water level rises in the container, f means falls, s means stays the same. Combination answers like 'f or s' are possible answers in some of the cases. - The new sphere has a radius of r = ro and a density of p< Po- - The new sphere has a density of p > Po and a mass of m = mo. - The new sphere has a radius of r = ro and a mass of m < mo- Submit Answer Tries 0/12

Name: A soliă, homogeneous sphere with a mass of mo, a radius of ro and a d
Uploaded: 2024-03-20T06:56:55.000Z
Channel: Bartleby
Description: A soliă, homogeneous sphere with a mass of mo, a radius of ro and a density of po is placed in a container of water. Initially the sphere floats and the water level ismarked on the side of the container. What happens to the water level, when the ori

Principles of Heat Transfer (Activate Learning with these NEW titles from Engineering!)

8th Edition

ISBN:9781305387102

Author:Kreith, Frank; Manglik, Raj M.

Publisher:Kreith, Frank; Manglik, Raj M.

Chapter5: Analysis Of Convection Heat Transfer

Section: Chapter Questions

Problem 5.5P: Evaluate the dimensionless groups hcD/k,UD/, and cp/k for water, n-butyl alcohol, mercury, hydrogen,...

See similar textbooks

Similar questions

1. A special-purpose piece of laboratory glassware, called a pyncnometer; is used to measureLiquid densities. It has a volume of 25 cc, and a mass of 17 .24 g when it is full of air. Whenfilled with a liquid of unknown density, its mass = 45.00 g. What is the density of this liquid?How large an error do we make if we ignore the mass of the air that was in it when we weighed itand found m = 17.24 g?
M1 U5: Use the general solution in determining the total hydrostatic force acting on the submerged curved surface. Please provide the complete UNITS ANALYSIS, USE OF CORRECT CONVERSION RATIOS and DIAGRAMS in your hand-written solution. INCOMPLETE/NO SOLUTION means NO CREDIT. Encode your FINAL answer in the space provided after each question. A curved surface is formed as a quarter of a circular cylinder with R = 0.75 m as shown. The surface is w 3.55 m wide. Water stands to the right of the curved surface to depth H = 0.60 m. seawater 0.60 m (SG = 1.03) %3D 0.75 m Determine the magnitude and direction of the horizontal component of the hydrostatic force (in N) acting on the gate. Indicate the direction by putting an R for right and L for left after your numerical answer. Your answer
Buoyance is an upward force exerted by a fluid that opposes the weight of a partially or fully immersed object. The upward buoyant force is calculated via the following equation: Fp = PfgV V is the volume of displaced fluid (object), pf is the density of the fluid, and F, is the buoyant force. 1) Calculate the buoyant force on 10 tons of solid steel completely submerged in water and compare this with the steel's weight with the density of 7800 kg/m³. (b) What is the maximum buoyant force that water could exert on this same steel if it were shaped into a boat that could displace 12m3 of water?
You are performing a pressure/elevation calculation is US units using the specific weight of water at 4C, which is 62. 4 b/f² . Your calculations leave you with a value of p = 10.0 /f².which you recognize is not a valid pressure unit. Complete the question by converting the b/f2 quantity into /in² . What is the pressure in lb/in2 ?
In Figure below all fluids are at 20 deg.C. Determine pressure at point B, if pressure at point A is 150 kPa and weight of air is neglected. Use the table below for the densities at 20 deg.C. Liquid p. kg/m Kerosene - Ammonia 608 Benzene 881 Air Carbon tetrachloride 1590 Benzene Ethanol 789 Ethylene glycol Freon 12 B 1117 40 cm 9 cm 1327 20 cm Gasoline 680 14 cm Glycerin Kerosene 1260 t8 cm 804 Mercury- Water Mercury Methanol 13,550 791 SAE 10W oil 870 SAE 10W30 oil 876 SAE 30W oil 891 SAE 50W oil 902 Water 998 Seawater (30%e) 1025
A platinum disc aboard the International Space Station has a thickness of 6 in. and a diameter of 2 ft. What is the weight (in Ib) of the disc? Assume that the simulated gravity on the Space Station, g. is 6.44 ft/s. The density of platinum is 21,450 kg/m²? (Report to the nearest whole number)
A 12 kN sphere is attached to a 4 kN sphere by a cable. Both spheres have the same diameter of 1.2 m and the weight and volume of the cable is negligible. If the spheres are thrown in water, calculate the following:a. The draft of the 4 kN sphere in meter.b. The tension in the cable in kilonewton.c. The exposed volume of the 4 kN sphere in cubic meter.d. Percentage of submerged volume of 2 spheres.
What height of a column of special gage liquid (sp gr 1.85) would exert the same pressure as a column of fluid A 3.67 meters high (sp gr 0.84)
Answer the following. A: When the pressure of liquid is increased from 3.5 MN/m² to 6.5 MN/m² its volume is found to decrease by (0.08) percent. What is the bulk modulus of elasticity of the liquid? B: An open cylindrical tank (1.2m) in diameter and (1.8m) deep is filled with water and rotated about its central axis at (60 r.p.m). How much liquid is spill and how deep of the water at the central axis.
A block of wood floats in water with 7 inches projecting above the water surface. If the same block were placed in alcohol of sp.gr. 0.82, the block would project 4 inches above the surface of the alcohol. Determine the specific gravity of the wood block.(please include units) - Fluid mechanics Answer: 0.98
1.When a double-bottom tank is full of fresh water it holds 120 tonnes.Find how many tonnes of ol of relative density 0.84 it will hold. 2. A tank measures 20 m. X 24m X 10.5 m. and contains oil of relative density 0.84.Find the mass of oll it contains when the ullage is 2.bm. (Ulage is the distance from the surface of the liquid in the tank to the top of the tank)
The two-pan balance scale of Fig. a 400-mm-long bar that fits loosely over a 20-mm-diame- ter shaft. The center of mass of the bar coincides with the center of the shaft. The scale functions by placing an item to be weighed (for example, a mini-TV) in the right pan and then placing known weights in the left pan until the scale is in equilibrium. However, because of bearing fric- tion, the system can be in equilibrium for more than a sin- gle value of weight in the left pan. If the coefficient of fric- tion between the bar and the shaft is 0.30, determine the range of weights that can be placed in the left pan to bal- ance an 80-N object placed in the right pan. consists of -200 mm 200 mm -