Answered: A solid circular bar is acted upon by…

A solid circular bar is acted upon by tensile force of 30 N. The diameter of circular Bar is 10 mm. The change in length of bar is 0.2 m, Original length is 10 m. Determine stress and strain produced

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Related questions

Q: A bar is compressed to half of its original length. Determine the magnitude of true strain produced…

Q: What is the transformation of strain at a point?

A: The strain transformation at a point occurs only when the stress acting on the material is plane…

Q: Q3/ A specimen having a rectangular cross section 0.000721mm2 is pulled in tension with 55,500 N…

A: A=0.000721 mm2T=55500Nyoung;s modulus (E)=70GPa∑=70*109Pa=70*103MPa=70*103 N/mm2

Q: For a steel sample under tensile testing, if the first principal strain was equal to 0.005 and all…

A: In continuum mechanics, Lamé parameters (also called the Lamé coefficients, Lamé constants or Lamé…

Q: Question 3: a. A mass of (Z + 50) kg is hung on a steel wire of diameter (Z + 5) mm and the…

A: We are suppose to solve only one question. Please post other question as a separate question.

Q: A small room is made up of rectangular metal bars. One bar has a width of 10 mm and would be able to…

A: Given:w=10 mmσc=20 MPa

Q: 2. An elastic rod of 25mm in diameter, 200mm long extends by 0.25mm under a tensile load of 40KN.…

Q: A bar is compressed to half of its original length. Find the magnitude of true strain produced in…

Q: If Pi=20,000 lb & P2=50,000 lb, determine the strain energy of the rod. Evaluate whether this value…

Q: 9- What strain will be produced by a stress of 40 x 106 N/m2, for a given modulus of elasticity…

A: Given: Stress= 40x106 N/m2 Modulus of Elasticity = 200 GPa

Q: 6.A metal rod 150cm long and of diameter 2cm is subjected to an axial pull of 20KN. What will be the…

Q: A rod is 0.5 m long and 5 mm diameter. It is stretched 0.06 mm by a force of 3 kN. Determine the…

Q: Calculate the strain (e) for a change in length (ō) and a length (L), where Ŏ = 0.015 in and L = 5…

A: Given data : Initial length L=5 ft Change in length δ=0.015 in Required : Strain

Q: A tensile specimen of cylindrical brass cartridge subjected to a load of 150 kg has a cross section…

Q: A bar is 500 mm long and is stretched to 505 mm with a force of 50 kN. The bar is 10 mm diameter.…

Q: Sketch a representative stress-strain digrama for a ductile material showing the following on it…

Q: A material specimen with an original length of 2.75 feet is subjected to a tensile load of 485 kips…

Q: Q2/ A metal rod of cross-sectional area 100 mm 2 curries a maximum tensile loud of 20 kN. The…

A: Suppose a normal load 'P' is applied on a rod having cross-sectional area 'A' and modulus of…

Q: A bar produces a lateral strain of -70 × 10-5 when subjected to tensile stress of magnitude 400 MPa…

A: Given, Lateral strain = εl = -70 x 10-5 Tensile axial stress = σ = 400 MPa Poisson's ratio = μ = 0.3…

Q: Find the value of strain if stress is 55 N/mm2 and elasticity is 10000 N/mm2

Q: The length of a wire increases from 1.25 m to 1.2508 m when a load of 12 kg is suspended. The radius…

Q: A metal wire is 2.5 mm diameter and 2m long. A force of 12 N is applied to it and it stretched 0.3…

Q: 3. If the engineering strain in a tensile bar is 0.0025 and Poisson's ratio is 0.33, find the…

Q: A cylindrical bar of metal having a diameter of 18.8 mm (A=278 mm^2) and a length of 198 mm is…

A: Bar diameter, d=18.8mm=0.0188m Cross sectional area of the bar, A=278mm2=0.000278 m2 Length of the…

Q: The change in length of a material is, mm, when the longitudinal strain and original length values…

Q: What are the two parts of strain-energy density?with

A: The strain energy per unit volume is known as the strain energy density also can be described as the…

Q: For a given material, the ratio of lateral strain to linear strain is observed as 0.2 when axially…

A: Option b is correct

Q: Find the value of strain if initial length of rod is 100 m and change in length of rod due tensile…

A: Given data : Initial length of rod=L Change in length of rod=∆L Required : Strain

Q: A tube has 25mm outside diameter and an axial tensile load of 40 kN. If the strain on the tube is…

Q: Compound axial member ABC has a uniform diameter of d=1.45 in. Segment (1) is an aluminum…

A: Given, A compound axial member made of Aluminum and copper Diameter of the axial member, d=1.45 in.…

Q: If longitudinal strain for a wire is 0.03 and its Poisson's ratio is 0.5, then its lateral strain is

Q: A pipe has an outside diameter of 3m and an inside diameter of 2.9m. It is acted upon by a tensile…

Q: Find the value of strain if stress is 4 N/mm2 and elasticity is 10000 N/mm2

Q: When a homogeneous isotropic material is subjected to a state oftriaxial stress, the strain in each…

A: In a homogeneous material, all the properties are the same at each and every point of the material.…

Q: n of aluminum having a rectangular cross section 9.6 mm × 13.0 mm (0.3780 in. × 0.5118 in.) is…

A: Given:Area, A=9.6*13.0 mm2F=35800 NE=69 GPa

Q: For ductile and linearly elastic material, stress is directly proportional to strain a. Below or at…

A: 1.Option (a) Below or at the yield point only. Is correct option Explanation: Stress is directly…

Q: A steel bar is stressed to 280MPa.The modulus of elasticity is 205 GPa. The bar is 80mm diameter and…

Q: A metal bar 5.0 m long extends by 0.05 mm when a tensile load is applied to it. The percentage…

Q: A bar produces a lateral strain of magnitude 60x105 m/m when subjected to a tensile stress of…

Q: A mild steel specimen of Diameter 9 mm, Length 16 cm is subjected to tensile load and it is found…

Q: A rod is subjected to a uniaxial load within linear elastic limit. When the change in the stress is…

A: Given data: The change in stress in the rod is σ = 200 MPa. The change in stain in the rod is ε =…

Q: At the proportional limit, the axial load of a 0.70-in- diameter bar was 5400 lb. A 2.20-in. gauge…

Q: round bar of 25mm in diameter undergoes a tensile load of 120kpa. The gage length is 30cm and…

Q: True stress-strain Engineering stress-strain strain Calculate the engineering ultimate tensile…

Q: What strain will be produced by a stress of 80 x 106 N/m2, for a given modulus of elasticity 200GPa.…

A: Given, stress = 80 x 106 N/m2 modulus of elasticity (E) = 200GPa= 200x 109 N/m2

Q: Determine poisson ratio if lateral strain -0.01 and longitudinal strain is 0.02

A: Given data : The value of lateral strain=εT The value of longitudinal strain=εL To find :…

Q: specimen of a metal 75 mm long was stretched with a force of 10 kN. The strain produced in the…

Q: Determine Stress and strain Draw the stress strain diagram Determine the following mechanical…

A: a) Please refer the following table for stress and strain calculations. Calculations are done using…

Question

Help me sir

A solid circular bar is acted upon by tensile force of 30 N. The diameter
of circular Bar is 10 mm. The change in length of bar is 0.2 m, Original
length is 10 m. Determine stress and strain produced

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A tensile force of 10 kN is applied on a 0.02-m diameter and 2-m long rod. After applying theload, the diameter of the rod decreases to 0.01998 m and the length increases to 2.01 m. The lateral (transverse) strain is?
A metal bar 5.0 m long extends by 0.05 m when a load is applied to it. The strain is?
Asap
A bar is compressed to half of its original length. Find the magnitude of true strain produced in the deformed bar.
A metal wire is 2.5 mm diameter and 2m long. A force of 12 N is applied to it and it stretched 0.3 mm. Determine the stress, strain and tensile modules of the wire.
A 0.1-in wire that is 10-in long and supports a 100-lb weight stretches a total of 0.1-in. What is the strain for the wire?
A mild steel rod of 12mm diameter was tested for tensile strength with the gauge length of 60mm. After the test final length and the final diameter were 80mm and 7mm, respectively. Find the strain in the transverse direction
Tensile test specimens are extracted from the "X" and "y" directions of a rolled sheet of metal. "x" is the rolling direction, "y" is transverse to the rolling direction, and "z" is in the thickness direction. Both specimens were pulled to a longitudinal strain = 0.15 strain. For the sample in the x-direction, the width strain was measured to be ew= -0.0923 at that instant. For the sample in the y-direction, the width strain was measured to be gw=-0.1000 at that instant. The yield strength of the x-direction specimen was 50 kpsi and the yield strength of the y-direction specimen was 52 kpsi. Determine the strain ratio for the x direction tensile test specimen. Determine the strain ratio for the y-direction tensile test specimen. Determine the expected yield strength in the z-direction. Give your answer in units of kpsi (just the number). If the sheet is plastically deformed in equal biaxial tension (a, = 0, to the point where & = 0.15, calculate the strain, 6, that would be expected.
By application of tensile force, the cross-sectional area of bar Pis first reduced by 30% and then by an additional 20% Another bar Q of the same material is reduced in cross-sectional area by 50% in a single step by applying tensile force After deformation, the true strain in bar Pand bar Q will, respectively be (a) 0.5 and 05 (b) 0.58 and 0.69 (c) 0.69 and 0.69 (d) 0.78 and 1.00
Current Attempt in Progress Arigid steel bar is supported by three rods, as shown. There is no strain in the rods before the load Pis applied. After load Pis applied, the normal strain in rod (2) is 870 uin/in. Assume initial rod lengths of L- 156 in. and L2- 63 in. Determine (a) the normal strain in rods (1). (b) the normal strain in rods (1) if there is a 0.019in gap in the connections between the rigid bar and rods (1) at joints A and C before the load is applied. (c) the normal strain in rods (1) if there is a 0.019 in. gap in the connection between the rigid bar and rod (2) at joint B before the load is applied. Answers: (al e uinvin. (b) e- pin/in. (c) - uin/in.
A specimen of titanium alloy is tested in torsion and the shear stress–strain diagram is shown in Fig.a. Determine the shear modulus G, the proportional limit, and the ultimate shear stress. Also, determine the maximum distance d that the top of a block of this material, shown in Fig. b, could be displaced horizontally if the material behaves elastically when acted upon by a shear force V. What is the magnitude of V necessary to cause this displacement?
A tensile test was conducted on a mild steel bar. The diameter and the gauge length of the bar were 3cm and 20cm respectively. The extension was 0.21mm. What is the value of strain?