A simply supported wood beam with overhang is subjected to uniformly distributed load q. A simply supported wood beam with overhang is subjected to uniformly distributed load q.-1 m-250 mm200 mmThe beam has a rectangular cross section with width b = 200 mm and height h = 250 mm. Determine the maximum permissible value g if the allowable bendingstress is oa = 11.2 MPa, and the allowable shear stress is Ta = 1.50 MPa. (Enter the magnitude in kN/m.)18.72 XYour response differs from the correct answer by more than 10%. Double check your calculations. kN/m

Answered: Image /qna-images/answer/5572d345-74ad-445e-bea3-beebf6b4cb87.jpg

Answered: A simply supported wood beam with…

Engineering

Civil Engineering

A simply supported wood beam with overhang is subjected to uniformly distributed load q.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The rectangular wood beam is loaded as shown in the figure. Determine the largest allowable magnitude of the load P if the working stresses are 10 MPa in bending and 1.2 MPa in shear. P 150mm 8 kN/m 2m 1m B C 250mm
A simply supported wood beam with overhang is subjected to uniformly distributed load q. 9 1m- 250 mm 200 mm i The beam has a rectangular cross section with width b = 200 mm and height h = 250 mm. Determine the maximum permissible value q if the allowable bending stress is all = 11.8 MPa, and the allowable shear stress is Tall = 1.95 MPa. (Enter the magnitude in kN/m.) kN/m Need Help? m Read It
A 4-m simply supported timber beam is to be designed to carry a total uniform load of 10 kN/m including its own weight. The timber is 80% stress grade Apitong. The nominal size of the beam is 200 mm x 260 mm. Before installation, the width and depth are to be reduced by 10 mm. 7a Find the maximumshearing stress. a. 0.50 MPa C. 0.86 MPa 7b. Find the maximum bending stress. a. 12.50 MPa c. 11.20 MPa 7c. Find the maximum deflection. a. 18.43 mm C. 14.50 mm b. 0.63 MPa d. 1.20 MPa b. 8.50 MPa d. 10.11 MPa b. 25.63 mm d. 12.60 mm
Problem Sets - 2: The rectangular wood beam is loaded as shown in the figure. Determine the largest allowable magnitude of the load P if the working stresses are 10 MPa in bending and 1.2 MPa in shear. P 150mm 8 kN/m 2m 1m B C 250mm
Let the allowable stresses in the post be ??? = 120 ??? and ??? = 6 ???. Compute the maximum safe axial load P that may be applied. The moduli of elasticity are 200 GPa for steel and 14 GPa for concrete. Each steel bar has cross-sectional area of 900??2
INELASTIC BENDING OF SINGLY REINFORCED CONCRETE BEAM SECTION *A trapezoidal concrete beam is casted with a compressive strength of about 20 MPa. The beam is reinforced with 3- 32 mm diamater bars in the tension zone with a yield strength of 275 MPa. The bar is located 100 mm from the bottom. Determine the nominal bending strength. Assume that the beam is symmetrical about the vertical axis with a depth of 600 mm, a top width of 500 mm, and a bottom width of 200 mm.
5. The wood beam has an allowable shear stress of Tallow = 7 MPa. Determine the maximum shear force V that can be applied to the cross section. (Practice at Home) 50 mm 50 mm 50 mm 100 mm tu 50 mm 200 mm
An axial load P is supported by a short steel column, which has a cross-sectional area of 11200 mm². If the average normal stress in the steel column must not exceed 110 MPa, determine the minimum required dimension "a" so that the bearing stress between the base plate and the concrete slab does not exceed 15 MPa. O 185 mm O 313 mm O 287 mm O 206 mm O 239 mm
A simply supported beam 300 mm wide, 500 mm deep and spans 6 m supports a service super imposed dead load of 10 kN/m and service live load of 6 kN/m. Concrete strength f’c = 21 MPa and steel yield strength fy = 415 MPa. Concrete cover to bar centroid is 70 mm. Determine the type of failure when ultimate loading is applied. A. Tension Controlled B. Transition Failure C. Compression Controlled D. Balanced Strain Failure
Two pieces of lumber having square section (b x b) are arranged and supported as shown. The horizontal lumber is hinged at the left and free at right. The right end carries a concentrated load P. The vertical lumber supports the horizontal lumber at the midspan. Find the following: a) maximum shear stress, b) maximum bending stress, and c) maximum compressive stress. Hinge DATA FOR PROBLEM P L b (N ) (m ) (m m ) (m m ) 6 5040 1.47 140 140
A floor slab 100 mm thick is cast monolithically with beams 250 mm wide 450 mm deep spaced 1.2 m on centers, on simple supports over a span of 5.0 m. The floor supports a service live load of 2.1 kPa. Using f'.= 21 MPa, rebar strength fy = 415 MPa, calculate the following if a typical interior beam is reinforced with 3- %3D 16-mm-dia. flexure bars at the bottom enclosed with 10-mm-dia. stirrups: 1. Nominal moment capacity (kN•m) of a typical interior beam in positive bending considering T-beam geometry. В. 86.99 A. 96.66 C. 91.10 D. 81.99 Maximum factored uniformly distributed load (kN/m) a typical interior beam can sustain against positive bending. 2. А. 30.93 В. 27.83 С. 26.23 D. 29.15 Maximum service superimposed dead load in kPa. В. 11.08 3. А. 17.73 С. 16.52 D. 14.77
Which of the following is an allowable stress design concept. O Alternate Basic Load Combinations O OMn O 1.2D+1.6L O Rn = FyAg