A simply supported beam having a length of 11.5 m, carrying a uniformly distributed dead load of 6 kN/m, and a uniformly distributed live load of 9 kN/m. The following properties are recorded in the beam: Ig = 9000x10^6 mm^4, Icr = 4500x10^6 mm^4, Ec = 21,000 MPa, Mcr = 100 kN-m. .) Determine the value of Ma -) Determine the value of le(DL+LL) ) Determine the value of Instantaneous deflection of lidspan (DL+LL)

A simply supported beam having a length of 11.5 m, carrying a uniformly distributed dead load of 6 kN/m, and a uniformly distributed live load of 9 kN/m. The following properties are recorded in the beam: Ig = 9000x10^6 mm^4, Icr = 4500x10^6 mm^4, Ec = 21,000 MPa, Mcr = 100 kN-m. .) Determine the value of Ma -) Determine the value of le(DL+LL) ) Determine the value of Instantaneous deflection of lidspan (DL+LL)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

An 8-m simply supported beam carries a concentrated load of 40 kN at a distance of 3.25 m from the left support. How far (m) from the left support is the location of the maximum deflection? The flexural rigidity EI is equal to 10000 kN-m². Enter a positive value. Just indicate the direction of the deflection in your solution.
Distributed load(s) of 50 kN/m may occupy any position(s) (either continuously or in patches) on the girder PQRST as shown in the figure (not drawn to the scale) R. P. Q 1.5 m 3 m 2 m 1.5 m
1. *A propped cantilever has a 2m overhang. The beam has a load of 2W applied half way between the fixed support and the roller support and a load of W applied at the free end. What is the minimum value of W that will cause the beam to collapse? The beam has the cross-section shown below. The yield stress is 300 MPa. 75 mm 15 mm 300 mm 2W C D 15 mm 250 mm 15 mm, 2m B + 2m 2m
350mmi The simply supported beam has an I-shaped cross section. (1) Determine the values and locations of the maximum tensile and compressive bending stresses. (2) Sketch the bending stress distribution over the cross section on which the maximum bending stress occurs. No credits if free body diagram is not present. 0 35m 11mm 8 kN/m 100 kN 7.5mm 11mm 0.8 m 2 m 54 1.0m 175mm 1100KN
12 KN Q 1 find stress Rod Rod D TCD ТАВ AB CD beam 10 m A uniform beam supported by two beam have cross sectional area 25 for AB and 12 for CD determine position d
A cantilever 2.5 m long is loaded with a uniformly distributed load of 10 kN/m over a length of 1.5 m from the fixed end. What will be the deflection at free end of the cantilever? [Take EI = 1.9 x 1012 Nmm2]
PROBLEM 2.78 A vibration isolation unit consists of two blocks of hard rubber bonded to plate AB and to rigid supports as shown. For the type and grade of rubber used r =1.54 MPa and G=12.6 MPa. Knowing that a centric vertical force of magnitude P=13 kN must cause a 2.5-mm vertical deflection of the plate AB, determine the smallest allowable dimensions a and b of the block. 75 mm bnin = 56.3 mm = 20.5 mm a min
A cantilever of 3 metres length and of uniform rectangular cross section 150 mm wide and 300 mm deep is loaded with a 30 kN load at its free end. In addition to this it carries a uniformly distributed load of 20 kN metre run over its entire length, Calculate: (i) The maximum slope and maximum deflection. (ii) The slope and deflection at 2 metres for the fixed end. per Take, E = 210 GN/m² %3D
A continuous beam is loaded as shown 1. Which of the following gives the fixed end moment AB in kN-m? a. 12 kN-m b. 8 kN-m c. 10 kN-m d. 5 kN-m 2. Which of the following gives the distribution factor at B for the member BA in %? a. 33.3% b. 66.6% c. 35.47% d. 45% 3. Which of the following nearly gives the moment at B using moment distribution method in kN.m? a. 12.89 b. 13.2 c. 11.2 d. 14.6
A steel rod has a hexagonal cross section with 10 mm on each side. If the working stress is 110 MN/m², determine the maximum axial load (kN) it can carry a. 41.90 c. 58.05 b. 28.58 d. 77.15 Ans: ||
For the structure shown below, if E is constant, what is the distribution factor at ?joint B (DFBA F 2 kN/m , 8 kN 2 m D 21, 21 21, Overhang- 4 m 5 m 4 m 3 m اخترأحد الخيارات a. 0.476 b. 1 c. 0.5 d. 0.238 e. 0.286 f. 0
Determine the maxi mum shear stress deue loped in the beam 5 KN/m Ø4 cm Ø3 cm 3 N/m 0.2 m 0-2m 0.2