A simple p*n junction is designed to work as IMPATT diode. The doping concentrations in the p* layer is 1019 cm-3 while the doping in the n-layer is 0.7 x1016Calculate the peak electric field if the breakdown voltage is 80 V and the dielectric constant is 11.9. Express your answer in the unit of kV/cm.cm-3

Doping concentration in p-layer, NA=1019 cm-3.Doping concentration in n-layer, ND=0.7×1016…

A simple p*n junction is designed to work as IMPATT diode. The doping concentrations in the p* layer is 1019 cm-3 while the doping in the n-layer is 0.7 x1016 cm-3. Calculate the peak electric field if the breakdown voltage is 80 V and the dielectric constant is 11.9. Express your answer in the unit of kV/cm.

A simple pn junction is designed to work as IMPATT diode. The doping concentrations in the p layer is 1019 cm-3 while the doping in the n-layer is 0.7 x1016 cm-3. Calculate the peak electric field if the breakdown voltage is 80 V and the dielectric constant is 11.9. Express your answer in the unit of kV/cm.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter12: Electronic Control Devices

Section: Chapter Questions

Problem 3RQ: Diodes and rectifiers allow current to _________. flow in one direction only flow in both...

See similar textbooks

Similar questions

Diodes and rectifiers allow current to _________. flow in one direction only flow in both directions divide paths of flow none of the above
2. Draw the graph of the voltage across the 10K resistor (calculate the values for the different voltages across the 10K resistor) of the circuit in the figure, knowing that the voltage source V is sinusoidal. And the diodes are silicon
decreases remains the same The doping level in a zener diode is that of a crystal diode. equal to less than more than same as A semiconductor diode allows current flow when there is no potential on the n-type or p-type materials 11
In the Figure as shown below the current (I) will be equal to: ---- Assume that all diodes are silicon -practical diode model 4 KUZ lovt 32 KSL 2.2 mA O 2.3 mA O 2.4 mA O 1.1 mA O
Assuming an ideal diode model for all the diodes in the circuit below, chose the correct state (bias) for each diode. 9kO IN1199C R2 01 18KO IN11990 D3 IN1199C R3 V2 12 V R4 5kQ
The four layer diode in the circuit is conducting and provide 0.7V across the diode at the drop-out point, what is the bias voltage value VBIAS that opens the diode? BIAS R$ ww IKO K Vao-10V 1-4mA
what is the voltage across the diode? what is the current through the diode? what is the current through the 100 ohm in series with the 3V? what is the current through the 5V line?
we use the constant voltage drop model with Von = 0.6V for the diode
All of the diodes in the following circuit are Silicon w/ forward voltage 0.6V. Determine the value of the current I in amperes if R1 = 100 and R2 = 150 R1 I 10 V R2 Kt
The thickness of the PN depletion region increases when diode is Your answer The function of zener diode is to provide a constant output voltage to a load. this process is called Your answer One types of diodes are typically used for power supply applications which always called Your answer
Determine which diodes are forward-biased and which are reverse-biased in the configurations shown in Figure 4. Assuming a 0.7-V drop across each forward-biased diode, determine the output voltage. O+5 V -10 V R DI +s vOK D, -SVOKH D3 +s vOK D4 -5 voK DI -5VOK Dz OVout OVout +5 voK Figure 4.
Which of the following circuit elements is a typical example of semiconductor material? Lütfen birini seçin: O A. Capacitor O B. Inductor O C. Resistor O D. npn BJT O E. Voltage source