A silicon diode has a maximum allowable junction temperature of 150°C. Find the maximum allowable power dissipation at 25°C temperature if the diodes thermal resistance is 0.4 °C/mW. A. 238 mW B. 313 mW C. 600 mW D. 117 mW

A silicon diode has a maximum allowable junction temperature of 150°C. Find the maximum allowable power dissipation at 25°C temperature if the diodes thermal resistance is 0.4 °C/mW. A. 238 mW B. 313 mW C. 600 mW D. 117 mW

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter59: Motor Startup And Troubleshooting Basics

Section: Chapter Questions

Problem 12SQ: How is a solid-state diode tested? Explain.

See similar textbooks

Related questions

Q: B- For the open-loop transfer function, maximum overshoot, and settling time. 110 (s+4)(0.2s+10)…

A: Rise time is the amount of time it takes for a signal to pass two voltage thresholds: an upper and a…

Q: Discuss the system stability for all values of k. 54 +5³ +5² = -1-K₁s¹ ² 3 Q(s) = $¹4_

Q: A DC source has an open circuit voltage of 30 V and an internal resistance of 1.5 ohm. A resistive…

A: Given, A dc source has open circuit voltage, Vs=Vth=30 V Internal resistance, Rs=1.5 Ω

Q: Plot the polar plot and mark the crossover frequencies frequencies & margins for the T.F. G(s) = 27…

Q: Ques 2. Two coils connected in parallel across a 100V DC supply, take 10 A current from the supply.…

A: Given- Voltage V=100 Vcurrent I=10 APower P=600 WTo Find-The resistance of each coil.

Q: Discuss the various methods of mounting an accelerometer on a machine and describe the influence of…

A: ANSWER There are three methods of ACCELEROMETER MOUNTING. 1-…

Q: 5. What is static synchronous compensator (STATCOM)? What is the main advantages/disadvantages of…

A: STATCOM and SVC: STATCOM is also known as a static synchronous compensator which is a controlled…

Q: A single-phase full-bridge inverter has a DC input voltage of 123 V, and supplies an inductive load…

Q: Find the equivalent resistance RabRab for the circuit shown in (Figure 2). be 1.2 ΚΩ 4 kΩΣ 30 kΩΣ…

Q: As shown, the battery has emf ε = 18.0 V and the other circuit elements have values L = 0.400 H, R1…

A: NOTE_ “Since you have posted a question with multiple sub-parts, we will solve first three subparts…

Q: Using Nyquist criterion, study the closed loop stability of the system, whose open loop transfer…

Q: Problem 3: Obtain the currents i, and is for the circuit shown in Figure 3 using mesh analysis. +1 5…

A: Given: Circuit diagram,

Q: Vo Vo = - Vo V3 Vo == V₁ V₂0 M Different answer An ideal op-amp has all its inputs, namely v₁, V₂…

A: Given data: An ideal op-amp circuit is shown as below. Input is DC voltage. Express the output…

Q: draw k-map for function F1(A,B,C,D) = Σm(3,7,8,9,11,15) F2(A,B,C,D) = Σm(3,4,5,7,10,14,15) and…

A: The given functions are: F1(A,B,C,D) = Σm(3,7,8,9,11,15) F2(A,B,C,D) = Σm(3,4,5,7,10,14,15)

Q: Determine the (i) operating frequency and (ii) feedbac fraction for Colpitt's oscillator shown in…

Q: For the entire circuit in Fig. 4, calculate: Pover avery (a) The power factor Rower apparent (b) The…

A: Given a circuit Find the following Power factor Average power delivered by source Reactive power…

Q: Find current through R2 resistor. + V1 10 R1 5 II Select one: O a. 3.04 O C. O b. 2.67 3.75 O d.…

A: Given circuit:

Q: 5.164 20-4f 11₁₂=14001 pm a) If= 1.2.4 C 193 R₁=15-2 P=5KIJ-Pack

A: 5.16 P=4 RA=0.8 Ω Vo=1.5 V n1=1400 rpm Solution- a) If=1.2 A RL=15 Ω PL=5kW=Pout From…

Q: Ex5: Find the current (1) using superposition.

A: The superposition theorem state that the sum of response of individual sources acting alone is equal…

Q: How fluorescent lights work?

A: A long arc source of light is a fluorescent bulb. A glass tube that is filled with only an inert gas…

Q: What is RG rating of coaxial cable? Give detailed answer please

Q: A power amplifier in a microwave link generates an output signal power of 10.XY Watts with a…

A: Given, XY=54 Output signal power, S=10.XY W Input signal power, N=15.XY mW Maximum bandwidth…

Q: 4. Three capacitors, C1 = 5 µF, C2 = 10 μF, and C3= 20 µF, are connected in parallel across a 150-V…

Q: 5.29 A magnetic field propagating in free space is given by H(z, t) = 20.sin(π × 108t+Bz) ax A/m…

A: It is given that: Hz,t=20.sinπ×108t+βzax Am

Q: R V 100 V 0-200 V

Q: Ex5; Find the current (I) using superposition. 24 V 12V 4 Ω Μ a ε Ι 8 Ω 3 Ω Μ 4Ω 3 Α

Q: R V 100 V 0-200 V

Q: Q1-A- Find the unit-step time response of the closed-loop second-order control system of the…

Q: Solve the output voltage Vo of the given circuit below. ID1 Ge 31.3 V 17.6 V 39.3 V 32 V 31.7 V Si…

Q: K The range of K for stability of a unity feedback system whose open-loop transfer function is G(s)…

A: Given, Open loop transfer function, Gs=Kss+1s+2 Unity feedback, Hs=1

Q: 4: Using superposition, find the current through the (202) resistor for the circuit below. 202 El 12…

Q: There are 175 slots in a 3-phase, 16-pole, 50 Hz., star connected alternator. There are 4 conductors…

A: We have an star connected alternator we have, slots = 175 Poles (p) = 16 frequency (f) = 50 Hz 4…

Q: Express the Boolean function F = A + B ′ C + A D as a sum of minterms.

A: It is given that: F=A+B′C+AD

Q: 3. According to Equal Area Criterion method, please explain how series capacitive compensation…

Q: 1-4. Write a set of state equations for the electrical network shown in Fig. 1-P4. R₁ www reeemmm R₂…

A: Since you have posted the multiple questions so we are supposed to answer the 1st one.

Q: Two capacitors of 20 μF and 30 μF are connected in parallel to a 300 volt DC supply. Then find (1)…

Q: Q10/Chose the correct answer for the output Q3 of the following circuit ( Assume that A=…

A: Given circuit,

Q: Create five(5) Maxwell Mesh problem with figure and solve it(Show complete solution)

A: The Maxwell mesh analysis is used to find the unknown current in the mesh present in the circuit.…

Q: A 100 km long three phase transmission line has resistance 12Ω per phase, inductance per phase 0.15…

Q: 2. Write the Boolean equation for the following circuit & Simplify the equation, A B C- X

A: Given Boolean circuit,

Q: An inductor of 2 henrys, a resistor of 16 ohms and a capacitor of 0.02 farads are connected in…

A: Given that a series circuit consists of L=2H, R=16 ohm, C=0.02 F, and emf E=300 V. All initial…

Q: For a periodic signal v(t) = 30 sin100t + 10 cos300t + 6 sin(500t + π/4), the fundamental frequency…

A: Given- V(t)=30sin100t+10cos300t+6sin(500t+π/4)To Find-The fundamental frequency in rad/s.

Q: SO TO 5mA (1) 10K2 Vo₂ (10.01 Vo ✓ 100 MA 20 KS

Q: Q2-The open-loop transfer function of a unity feedback control system is find: 40.69 10 (0.5 s²+s)…

A: Closed-loop systems that employ feedback enhance control by automatically altering the controller…

Q: For the circ a. Find RT. b. Find I. c. Find V1 and V2. of Fig. (1) d. Find the power to the 42 and…

Q: A.C. to transmit the same power and for the same loss and the same lamp voltage. Compare the copper…

A: Assuming that the power delivered in the two-wire DC system is P, the resistance per conductor be R1…

Q: Question 1:find Vo 5Ω www 4Ω Vo +1 1Ω Μ 3 Ω 9V +)3V

Q: A single-phase full-bridge inverter has a DC input voltage of 123 V, and supplies an inductive load…

Q: find the result

Q: For the following circuit, find the current through the (10k 2) resistor using Thevenin's Theorem.…

A: Given: Circuit

Question

A silicon diode has a maximum allowable junction
temperature of
150°C. Find the maximum allowable power
dissipation at 25°C temperature
if the diodes thermal resistance is 0.4 °C/mW.
A. 238 mW
B. 313 mW
C. 600 mW
D. 117 mW

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Three Phase Controlled and Uncontrolled Rectifiers

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

How is a solid-state diode tested? Explain.
Consider a junction diode has dc biased current at operating point ID=0.8 mA. A sinusoidal voltage is superimposed on the VD such that the peak-to-peak sinusoidal current id(t) = 0.05ID. Find the value of the applied peak-to-peak sinusoidal voltage vd(t).
3: Using silicon diode design a clamper that will produce output V,-20Sin wt+10 (v) when the input voltage is Vo=20Sin wt-10 (V).Draw the circuit diagram and the input and output signals. 4:The 6-V zener diode has a maximum rated power dissipated of 690 mw.Its reveres current must be at least 3mA to keep it in breakdown. Find a suitable value for Rs if V; can vary from 9v to 12v and Ri. can vary from 5000 to 1.2KO.
A silicon diode is in parallel with a germanium diode and is connected to a load resistor having a value of 20 kQ and a forward supply voltage of 10 V. What is the approximate voltage across the silicon diode? * A. 10 V B. 1.0 V C. 0.7 V D. 0.3 V
For the circuit shown in the figure below, consider the diode as an ideal diode & R.M.S value of source voltage as Vs. The output voltage waveform at R is most likely to have zero value in the positive half cycle and a peak value of 1.414Vs in the negative half суcle sine-wave nature with a peak value 1.414VS zero value in the negative half cycle and a O peak value of 1.414Vs in the positive half сycle O sine-wave nature with a peak value Vs
4. For the circuit shown in the figure below uses a transformer of 230V/12V-0-12V and all diodes are Ge find the following, RL-3.3k2. The name of the circuit is ........ Current through the load is............The DC output voltage is............ Draw the input & output wave forms ✈ ellel eetee CT D₂ DE www R₂
A diode whose internal resistance is 20 ohms is to supply power to a 1000-ohm load from a 110V(rms) source of supply. determine the percent regulation from no load to the given load. A 1.81 % B 2.06 % C 3.19 % D 5.45 %
Design a clipping circuit that will limit the output voltage to 5V when applying an input sinusoidal waveform with a peak value of 10V. Assume available diodes with voltage drop of 0.5V. Sketch the output waveform of the circuit.
C. In the circuit shown below the knee current for the ideal Zener diode is 10 mA Calculate the minimum value of load resistance RL in order to maintain 5 volts across the load resistance RL 2. WW-
A silicon diode with a forward resistance of 100 is connected in series with a 5000 resistor. If an a.c voltage of 20V peak is connected across the series combination of the diode and the resistor what will be the peak value of the current through the diode and the peak output voltage? What will be the peak value of the current through the diode and the peak output voltage if the diode were ideal?
0:- Consider the circuit in Figure a) What type of circuit is this? b) Find and Sketch the voltage waveform across RL, assume the diodes are practical. c) If 100uf capacitor parallel with the resistor, calculate the ripple is connected factor I O o D
There are two LEDs that can be used as a polarity detector. Apply a positive source voltage and a green light results. Negative supplies result in a red light. Packages of such combinations are commercially available.Find the resistor R to ensure a current of 20 mA through the “on” diode for the configuration. Both diodes have a reverse breakdown voltage of 3 V and an average turn-on voltage of 2 V