text only A series-connected load draws a current i(t) = 4 cos(100ml + 10) Awhen the applied voltage is u(t)= 120 cos(100m - 20°) V. Find theapparent power and the power factor of the load. Determine the ele-ment values that form the series-connected load.

It is given that : i(t) = 4 cos(100πt + 10°) A=4∠10° Av(t) = 120 cos(100πt − 20°) V=120∠-20° A…

A series-connected load draws a current i(t)= 4 cos(100mt + 10") A when the applied voltage is u(t)= 120 cos(100mr-20°) V. Find the apparent power and the power factor of the load. Determine the ele- ment values that form the series-connected load.

A series-connected load draws a current i(t)= 4 cos(100mt + 10") A when the applied voltage is u(t)= 120 cos(100mr-20°) V. Find the apparent power and the power factor of the load. Determine the ele- ment values that form the series-connected load.

Power System Analysis and Design (MindTap Course List)

6th Edition

ISBN:9781305632134

Author:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Publisher:J. Duncan Glover, Thomas Overbye, Mulukutla S. Sarma

Chapter2: Fundamentals

Section: Chapter Questions

Problem 2.7P: Let a 100V sinusoidal source be connected to a series combination of a 3 resistor, an 8 inductor,...

See similar textbooks

Related questions

Q: Find V2 in the following circuit using source transformation 72V 492 + www 3v₂ VCVS 692 1292

Q: 11. A factory draws 100A at a 0.7 lagging power factor from a 12,470 V, 60 Hz line. What capacitor…

Q: 6. Find the total power dissipated by all resistors in the circuit shown. (15.8W) 24 V 10 92 www ww…

Q: Given the following with Q=0 as initial state, What do the Q and Q0 waveforms look like? SET RESET Q…

A: Given: Set Reset inputs wave forms of SR flip flop. with Q=0 as initial state. To do: We have to…

Q: g(t) to 2 3 1 10 0 Find the Laplace transform of the gate function in Fig. 15.5.

Q: 8. Solve the following circuit for current in loop A, B and C. Use the following system of linear…

A: For the given circuit along with the system of linear equations, the loop current needs to be…

Q: The half-bridge resonant inverter with bidirectional switches is operated at a frequency of fo =3…

A: In this question we need to choose a correct option

Q: p-n junction diode at 25 temperature degree with reverse saturation current of 10-⁹ A

A: Temperature reverse saturation current and diode current is given as, T=250CI0=10-9AID=1A

Q: 3. An industrial load of 200KW has a power factor of 0.5 lagging. A group of synchronous motors…

A: industrial load PL = 200 KW and power factor is cosϕ1 = 0.5 lagging set of synchronous motors…

Q: Find the phase angle between i₁ = -4sin(377t +25°) and 1₂ = 5cos(377† -40°). Does i, lead or lag i2?…

A: Given: Current equations, i1=-4 sin377t+25°,i2=5 cos377t-40°, To find: Does i1 lead or lag i2?

Q: 173.2/0° volts . 10 ohms V₁ I • 41,= (Answers should be in whole numbers) 20 ohms We are finding the…

Q: Given this question for PMDC motor 1) Write the equations of motion for the DC motor in time domain…

A: It is asked to determine the equations of motion for the DC motor in time domain and s-domain.

Q: For the frequency divider circuit the D-flip-flop is a CD4013 Dual D-Type flip-flop V2 is a square…

A: According to the question, for the frequency divider circuit the D-flip-flop is a CD4013 Dual D-Type…

Q: Find power dissipated across R1 in mW V₁=8,8Volts, and R₁ =5,4k V1 Si Ge R1

A: V1=8.8 V, R1=5.4 kΩ. Given circuit diagram is,

Q: 5) Find the closed loop transfer function for the following block diagram by using block diagram…

Q: ?How many nodes in this circuit R₁ R₁ W

A: Circuit diagram is given as,

Q: JESTION 5 ZT->> R XL dz,'s magnitude in Ohm for R=12 (Ohm) and XL = 5 (Ohm). Answer range: +5%

Q: 15) For the operational amplifier shown, if Vi is 888 V, find Vo. 20 K ww 200 K www A. 187.78 mV B.…

Q: 100 Q2: A)Find the summation: Σ--∞ §(n +4)³√ √sin(2n)

A: it is asked to find the given summation

Q: 2-) For these circuits give the three terminal voltages and the three terminal currents, and state…

A: Given data Three BJT Circuits with VEE=15 V is given in the problem. Transistor current gain, β=100.…

Q: 4. Electrical equipment in an office takes a current of 13A from a 240V supply. Estimate the cost…

A: In this question we will find electricity cost...

Q: 4. v(t) = 750 cos (5000 t +30°) V (a) Find the peak value, the phase, the frequency, and the period…

A: V(t)=750cos(5000t+30°) v We need to calculate a) peak value, phase , frequency,time period of v(t)…

Q: Initially uncharged four capacitors are connected as shown in the Figure. Here, V₁ = 38,4 V, V₁ =…

A: Va = 38.4 VVb = 17.2 VC1 = 14 μFC2 = 35 μFC3 = 28 μF C4 = 7 μF

Q: The impedance for a capacitor C is: Select one: O a. 1/(SC) b. (SC) F

A: Capacitor of value C.

Q: 1. (a) A sinusoidal voltage with Veff = 10V is connected across Z₁ = 1 + j as shown in figure(a)…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three sub-parts…

Q: 2kIx 14 zk 2x Nodal Analysis Probz Vz IX → 1) АМА T 0.5k find V₁, V₂ (node 1 & mode 2) Io, Ix

Q: A square-wave inverter supplies an RL series load with R = 25 2 and L = 58 mH. the output frequency…

Q: Which resistor would the smallest current flowing? E Hillli Ο 25 Ohm O 75 Ohm 100 Ohm Ο Ο 10 Ohm…

Q: E = 10V ( I AC + VR - R=292 + VL XL Xc= 1027 + Vc What should XL at resonance? What is the magnitude…

Q: An oscilloscope shows peak-to-peak amplitude of 8 cm for a measured sinusoidal voltage waveform with…

A: In the given questions we need to calculate the average value of the given signal.

Q: 2- Given the following two-degrees of freedom translational mechanical system, use the "by…

A: The transfer function of the given mechanical translational system needs to be calculated by using…

Q: ? By using Current Divider Rule (CDR) find i1 & i2 + 11 12

A: The circuit is given that:

Q: A synchronous generator is connected to an infinite bus with excitation voltage Ef = 1.3 pu. The…

A: Excitation Voltage Ef = 1.3 puTermial Voltage Vt = 1.0 puSync. Reactance Xs = 1.1 puReal Power…

Q: find small signal gain Av. of the amplifier from Vin to Vout assuming that Rc = 5Kohms Rs = 0 and Rl…

A: β= 100Rc = 5 kΩRE = 200 Ω

Q: High humidity in a production environment can cause adhesion problems. However, low humidity…

A: OPTION (b) is correct answer

Q: VSF=11.69×10-9×100+1.8663=3.0353 V how come need to times 10^9?

A: here we have clear the calculation of VSFVSF

Q: A resonant inverter with bidirectional switch has C = 3uF, L = 25uH and Vs = 220V. Its secondary is…

A: Given that, C=3 μFL=25 μH and VS=220 V The switching time of the transistor is 10 μs fo=12 kHz

Q: 3. The Thevenin equivalent voltage, as seen by R, is most nearly_________V. a. 8 b. 20 c. 3.3 R6 w…

Q: 1. A single phase, 60Hz, 20-km short transmission line receives 700 MW at 0.95 lagging pf at 327.8…

A: “Since you have posted a question with multiple sub-parts, we will solve the first three subparts…

Q: For the circuit shown find the impedance phase angle Z (in degrees) i = 0.02 sin(157t +40)

A: Circuit diagram is given as,

Q: Problem 3 Is the following system controllable. Is the system observable? 0 A = [₁₂] B [], C = [10]…

Q: For a power station the yearly load duration curve is a straight line from 50,000 to 4000 kw. To…

A: Capacity of Generator 1 & 2 = 20,000 kW Capacity of Generator 3 = 7000 kW Pmax = 50000 kW Pmin =…

Q: Find the value of K in the system below that will place the closed loop poles as shown. Select the…

A: here we have to find the value of k for the given closed loop poles plot

Q: $ C₁ R₁ R₂ ww Vcc Re RE HH C₂ FIG. 4.28 Voltage-divider bias configuration. No 1cq Alc Q-point…

A: Asked to determine Base current operating point IBQ Collector current operating point ICQ Collector…

Q: The trigonometric Fourier series of an even function does not have the (A) dc term (B) cosine terms…

A: We know that, trigonometry Fourier series is period signal. It is represents a periodic function as…

Q: v(t)=83cos(10t) V, R = 40 Ohm, C = 0,007 F, L = 5 H . a) Calculate impedances for the…

A: The above question is based on single-phase AC circuit analysis. Since multiple subparts have been…

Q: Four strain gauges are mounted on a cantilever beam in a configuration like that shown in Figure 3.…

A: "Since you have posted a question with multiple sub parts, we will provide the solution only to…

Q: How does inductance impact the performance of a transmission line in terms of signal integrity and…

A: Signal Integrity: a. Impedance Mismatch: Inductance plays a crucial role in maintaining proper…

Q: (a) After the switch is first thrown to a (connecting the battery), what time interval elapses…

A: For the given RL circuit the value of time required to reach 220mA, Value of current at t-10s and…

Q: 2. A single phase, 60Hz, 200-km medium nominal- transmission line receives 700 MW at 0.95 lagging pf…

A: Given Data: A single phase, 200km, medium nominal-π transmission line with, Sending end power…

Question

text only

A series-connected load draws a current i(t) = 4 cos(100ml + 10) A
when the applied voltage is u(t)= 120 cos(100m - 20°) V. Find the
apparent power and the power factor of the load. Determine the ele-
ment values that form the series-connected load.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data:

VIEW

Step 2: Determining the apparent power and power factor:

VIEW

Step 3: Determining the impedance and circuit elements:

VIEW

Solution

VIEW

Step by step

Solved in 4 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

If a Load absorbs 10 kVA at a leading power factor of 0.6. Then the complex power is: Select one: a. 6000 - j8000 VA b. 6000 + j8000 VÀ C. -6000 - j8000 VA O d. None of these
What is the real power, reactive power and complex power delivered by the source in the given circuit? Current source is 10, angle 30 degrees A.
Find V and Power Factor of the Load. 13200Zφ V| Note: The angle of V is 0°. 5 + j7 Ω Mmm 70√320 A PL=300kW V=? PF=?
Show the solution Using 24v AC source design a 24v unregulated power supply circuit that will power a 1kohms load with 50mv ripple. Draw your designed unregulated power supply circuit
A load 300+j0 ohms is connected across a 240 V and 50 Hz supply. Find the total current. a. 1 A b. 0.8 A c. 3.5 A d. 3 A
A 50 Hz high voltage Schering bridge is shown in the figure. The component parameters are as follows under balanced condition: Cs-150 microfarad, C2-0.677 microfarad, R2-634 ohm, and R1-168 ohm. Find the dissipation factor of the tested material. 220V rms Lütfen birini seçin 0.1340 b.0.1672 E0051 0.0.0749 e.0.1128 88888888 00000000 25 kV rms R R₁ R₂ II (C₂ 12²
Three identical impedances are connected in star across a 440 V, 3 phase, 50 Hz supply. The line current is 40 A and the pf is 0.8 leading. Find the value of resistance and capacitance in each phase.
A voltage and current applied to a single phase load is v= 195 sin (300t+35°) and i= 175 sin (250t- 40°). Find the single and three phase active and reactive power of the circuit if the voltage and current are in cos waveform. Active Power Reactive Power Three Phase Active power Three phase Reactive Power
A non-sinusoidal current source (iT=2+1.5sin1000t+ 1cos3000t-0.5sin400Ot) A is applied to the circuit shown. Find the * ?total power 42 iL iT ic -J92 {J4Q 28 W 39 W 20 W 55 W
For the circuit given in Figure 1, a) Find the Thevenin equivalent circuit with respect to terminals a-b b) When a 5000 resistor is connected to terminal a-b, find the voltage on the resistor wwwwwwmm c) It will be connected to a-b terminals and its voltage on 5000 load will be 132 kV rms. What should be the capacitive reactance value that will increase it? wwwwwwwww d) What happens to the short-circuit current when the a-b terminals are short-circuited? 2+1202 000 m da 127/6 kV rms ob 1.5 +/902 000 w 12725 kV ms
For the admittance locus diagram shown below: find the value of each element in the circuit if w=377 rad/sec? * jB AB=BC A 600 1.1 B C
Use the information below to answer questions 24 und 25. The voltage across and the current through a load are (10+ j5Y and (2-jiArespecively. 24. What is the reactive power in VArconsumed? D. 0 A. 15 C. 20 D. 25 25. What is the pawer factor of the load? A. 0.8 leading B. 0.8 Jagging. -D. 0.6 ligging C 0.6 leading