A sequential circuit has two JK flip-flops A and B, two inputs x and y, and one output z. The flip-flop input equations and circuit output equation areJA=Bx+B′y′ KA=B′xy′ JB=A′x KB=A+xy′ z=Ax′y′+Bx′y′1. (a) Draw the logic diagram of the circuit.2. (b) Tabulate the state table.3. (c) Derive the state equations for A and B.

A sequential circuit has two JK flip-flops A and B, two inputs x and y, and one output z. The flip-flop input equations and circuit output equation areJA=Bx+B′y′ KA=B′xy′ JB=A′x KB=A+xy′ z=Ax′y′+Bx′y′1. (a) Draw the logic diagram of the circuit.2. (b) Tabulate the state table.3. (c) Derive the state equations for A and B.

Electric Motor Control

10th Edition

ISBN:9781133702818

Author:Herman

Publisher:Herman

Chapter22: Sequence Control

Section: Chapter Questions

Problem 6SQ: Draw a symbol for a solid-state logic element AND.

See similar textbooks

Similar questions

Design a logic circuit that illustrates Rule 11 of Boolean algebra: A+ AB = A + B A pulse generator is used to represent the input A and a switch is used for the input B. Switch B is open for B = 1 and closed for B = 0. Draw the logic circuit. Also, draw the timing diagrams for the following scenarios: i. B = 0 ii. B = 1
Design a combinational logic circuit with four inputs A, B, C, D and one output F as follows. The inputs ABCD represent a four-bit unsigned binary number where A is the most significant bit and D is the least significant bit. Whenever the inputs represent an even number between 0 and 10, the output F is logic 1. Otherwise F is logic 0. Show all your working.
Design the following combinational logic circuit with a four-bit input and a three-bit output. The input represents two unsigned 2-bit numbers: A1 A0 and B1 B0. The output C2 C1.C0 is the result of the integer binary division A1 A0/B1 B0 rounded down to three bits. The 3-bit output has a 2-bit unsigned whole part C2 C1 and a fraction part CO. The weight of the fraction bit CO is 21. Note the quotient should be rounded down, i.e. the division 01/11 should give the outputs 00.0 (1/3 rounded down to 0) not 00.1 (1/3 rounded up to 0.5). A result of infinity should be represented as 11.1. A minimal logic implementation is not required. (Hint: start by producing a truth table of your design).
A synchronous logic circuit has one JK and one D flip-flop. There is no output in the circuit. The entry is represented by an X. Y is the output of JK flip-flob, and Yo is the output of D flip-flobe. Logic functions of the inputs of flip-flops are given below. J = XY. K = X, D = XY, A Draw the state diagram of the synchronous circuit. Note: Take the states (Y, Yo) in 2 order.
4 7) For the following sequential circuit: a) Tabulate the state table. b) Derive the state and output equations. c) Re-design the circuit using T flip-flops. Q1 Q -y K, K QP Jo Qo Q Ko K Q clock. please solve it as soon as possible
Q2. A sequential circuit has two D flip-flops, two inputs x and y, and one output z. the flip-flop input equations and the circuit output are as follows: D₁ = xy + xA, DB=B+xA, z = B a. Draw the logic diagram of the circuit b.Tabulate the state table
2.1 Combinational logic circuits. Tabulates a truth table for the following Boolean expression shown in Equation 1.1. f = A.B.C + A.B.C + A.B.C (1.1) 2.2 Half adder. A half adder is a circuit that adds two binary digits, A and B. It has two outputs, sum (S) and carry (C). The carry signal represents an overflow into the next digit of a multi-digit addition. Figure 1.2 depicted a logic diagram for a half adder. a. derives the Boolean expression for s and c. b. tabulates a truth table for the half adder. Ao Bo Figure 1.2: Half adder os S C
2. Sequential circuit shown below has two flip-flops A and B and one input x. It consists of a combinatorial logic connected to the flip-flops, as shown in Figure below. Analyze the circuit: a. Derive the next state and output equations. b. The state table of the circuit. c. Draw the state diagram. A K. 2-t0-1 MUX Y B' CLK
Design a combinational circuit using multiplexer for a car chime based on thefollowing system: A car chime or bell will sound if the output of the logic circuit(X) is set to a logic ‘1’. The chime is to be sounded for either of the followingconditions:• if the headlights are left on when the engine is turned off and• if the engine is off and the key is in the ignition when the door is opened.Use the following input names and nomenclature in the design process:• ‘E’ – Engine. ‘1’ if the engine is ON and ‘0’ if the engine is OFF• ‘L’ – Lights. ‘1’ if the lights are ON and ‘0’ if the lights are OFF• ‘K’ – Key. ‘1’ if the key is in the ignition and ‘0’ if the key is not in the ignition• ‘D’ – Door. ‘1’ the door is open and ‘0’ if the door is closed• ‘X’ – Output to Chime. ‘1’ is chime is ON and ‘0’ if chime is OFF
7. For a sequential circuit of two D flip-flops 4 and B, two inputs X and Y. and one output Z which is described by the following input equations: DA-XY+XA D₂-XB+XA a. Draw the logic diagram of the circuit. b. Derive the state table. Z=XB
Consider the circuit below. The switches are controlled by logic variables such that, if A is high, switch A is closed, and if A is low, switch A is open. Conversely, if B is high, the switch labeled is open, and if B is low, the switch labeled is closed. The output variable is high if the output voltage is 5V, and the output variable is low if the output voltage is zero. a. Write a logic expression for the output variable. b. Construct the truth table for the circuit. A Logic 1 5V(+ B C Logic 0 R
Analyze the following sequential circuit: 1) What type of state machine is this circuit and why? 2) Write equations for flip-flop inputs and output (Y). 3) Derive the next-state equation for each flip-flop from its input equations. 4) Derive the State table. X A' B' LA DA D. A B