A seamless tube 32 mm outside diameter is turned on a lathe. The spindle speed used is100 rpm. Rake angle = 35°, depth of cut = 0.125 mm, chip compression ratio = 1.666,feed= 0.1mm/rev, coefficient of friction= 1.53, resultant cutting force= 215.5N. Using theorthogonal model to approximate turning, Calculate:(1) Velocity of chip relative to the tool and workpiece,(2) Forces acting on the chip and the tool during orthogonal cutting,(3) Stresses acting on the shear plane and power dissipated in the shear zone,(4) Specific energy.

Answered: Image /qna-images/answer/c366d259-3957-404f-afdc-cddcbd1626b4.jpg

A seamless tube 32 mm outside diameter is turned on a lathe. The spindle speed used is 100 rpm. Rake angle 35°, depth of cut 0.125 mm, chip compression ratio 1.666, feed%3D0.1mm/rev, coefficient of friction= 1.53, resultant cutting force% 215.5N. Using the %3D orthogonal model to approximate turning, Calculate: (1) Velocity of chip relative to the tool and workpiece, (2) Forces acting on the chip and the tool during orthogonal cutting, (3) Stresses acting on the shear plane and power dissipated in the shear zone,

A seamless tube 32 mm outside diameter is turned on a lathe. The spindle speed used is 100 rpm. Rake angle 35°, depth of cut 0.125 mm, chip compression ratio 1.666, feed%3D0.1mm/rev, coefficient of friction= 1.53, resultant cutting force% 215.5N. Using the %3D orthogonal model to approximate turning, Calculate: (1) Velocity of chip relative to the tool and workpiece, (2) Forces acting on the chip and the tool during orthogonal cutting, (3) Stresses acting on the shear plane and power dissipated in the shear zone,

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The following data was obtained from an orthogonal cutting test. Rake angle = 20° Depth of cut = 6 mm Feed rate = 0.25 mm/rev Cutting speed = 0.6 m/s Chip length before cutting = 29.4 mm Vertical cutting force = 1050 N Horizontal cutting force = 630 N Chip length after cutting = 12.9 mm Using Merchant's analysis, calculate (a) Magnitude of resultant force, (b) shear plane angle, (c) friction force and friction angle, and (d) various energies consumed.
Low carbon steel having a tensile strength = 300 MPa and a shear strength = 220 MPa is turned at a cutting speed = 2.5 m/s, feed = 0.20 mm/rev and depth of cut = 3.0 mm. The rake angle = 5° in the direction of chip flow. The resulting chip ratio = 0.45. Using the orthogonal model to approximate turning, determine the cutting force and feed force.
A turning operation is made with a rake angle of 10 degrees, a feed of 0.010 in/rev, and a depth of cut = 0.100 in. The shear strength of the work material is known to be 50,000 lb/in2, and the chip thickness ratio after the cut = 0.40. Determine the cutting force and the thrust force. Use the orthogonal cutting model as an approximation of the turning process.
In the lathe machine, the diameter of workpart 35mm is turned at 100 rpm, depth of cut 0.125 mm, length of continuous chip for one revolution of workpart = 60mm, length undeformed chip= 100.53mm, rake angle = 35°, coefficient of friction= 1.5 and resultant cutting force=215.5 N. Calculate: 1- Horizontal cutting force of the tool on the workpart and vertical cutting force required to hold the tool against the work. 2- The forces components applied against the chip by the tool. 3- Velocity of chip relative to the tool and workpart. 4- The percentage of total energy dissipated due to friction along the shear plane, and the friction at the tool-chip interface.
Turning is performed on a work material with shear strength of 250 MPa. The following conditions are used: v = 4.0 m/s, f = 0.25 mm/rev, d = 3.0 mm, and rake angle = 9* in the direction of chip flow. The resulting chip ratio = 0.5. Using the orthogonal model as an approximation of turning, determine: (a) the shear plane angle; (b) the shear force; (c) cutting force and feed force; (d) shear stress; (e) friction angle; (f) friction coefficient; (g) Discuss the effect of increasing shear angle on shear force and shear stress. Chip Tool Fa Work
A turning operation is performed with HSS tooling on mild steel, with Taylor tool life parameters n = 0.12, C = 60 m/min. Work part length = 450 mm and diameter = 80 mm. Feed = 0.20 mm/rev. Handling time per piece = 4.0 min, and tool change time = 1.5 min. Cost of machine and operator = $27/hr, and tooling cost = $2 per cutting edge. Find the a. cutting speed for maximum production rate and b. cutting speed for minimum cost Equations used n *-=c(")* Vmax = C 1-n Tt Vmin = C =c(₁" n 1 n Co n CoTt + Ct n
A HSS tool is used to turn a steel workpart that is 300 mm long and 80 mm in diameter. The parameters in the Taylor equation are: n=0.13 and C= 75 (m/min) for a feed of 0.4 mm/rev. The operator and machine tool rate = $30.00/hr, and the tooling cost per cutting edge = $4.00. It takes 2.0 min to load and unload the workpart and 3.50 min to change tools. Determine: a. Tutting speed for maximum production rate, b. Tool life in min of cutting, and c. Cycle time and cost per unit of product.
A HSS tool is used to turn a steel workpart that is 300 mm long and 80 mm in diameter. The parameters in the Taylor equation are: n = 0.13 and C = 75 (m/min) for a feed of 0.4 mm/rev. The operator and machine tool rate = $30.00/hr, and the tooling cost per cutting edge = $4.00. It takes 2.0 min to load and unload the workpart and 3.50 min to change tools. Determine: Tutting speed for maximum production rate, Tool life in min of cutting, and Cycle time and cost per unit of product. determine cutting speed for minimum cost.
A high-speed steel tool is used to turn a steel workpart that is 295 mm long and 75 mm in diameter. The parameters in the Taylor equation are: n = 0.15 and C = 80 (m/min) for a feed of 0.5 mm/rev. The operator and machine tool rate = $29.00/hr, and the tooling cost per cutting edge = $3.90. It takes 2.1 min to load and unload the workpart and 3.40 min to change tools. Determine (a) cutting speed for maximum production rate, (b) tool life in min of cutting, and (c) cycle time and cost per unit of product (d) cutting speed for minimum cost and tool life in min of cutting
Low carbon steel having a tensile strength of 450 MPa and a shear strength of 270 MPa is cut in a turning operation with a cutting speed of 2500 mm/s. The feed is 0.15 mm/rev, and the depth of cut is 0.25 cm. The rake angle of the tool is 12° in the direction of chip flow. The resulting chip ratio is 0.55. Using the orthogonal model as an approximation of turning, determine (a) the shear plane angle, (b) shear force, (c) cutting force and feed force.
The following data is given for slab milling of a 300 mm long 50 mm wide mild steel block: Cutter of diameter= 60 mm; Numbers of teeth =12; Cutter speed = 120 rev/min; Depth of cut = 3.2 mm; Feed is 0.25 mm/tooth.Determine (i) Table feed in mm/min, (ii) MRR (iii) Power (iv) Torque and (v) Total machining time. Assumesuitable approach and over-run and specific energy of mild steel as 5 Ws/mm3.
Q1. Calculate the time required to machine a workpiece 170 mm long, 60 mm diameter to 165 mm long 50 mm diameter. The workpiece rotates at 440 rpm, feed is 0.3 mm/rev and maximum depth of cut is 2 mm. Assume total approach and overtravel distance as 5 mm for turning operation. Answer Q2. A gray cast iron surface 280 wide and 540mm long may be machined either on a vertical milling machine, using a 100mm - diameter face mill having eight inserted HSS teeth, or on a horizontal milling machine using an HSS slab mill with eight teeth on a 200-mm. diameter. Which machine has the faster cutting time? The values of feed per tooth and cutting speed for both processes are 0.4mm/tooth and 80m/min, respectively. The depth of cut = 3.0 mm and assume A and O equal to 5. Answer