A round solid cylinder made of a plastic material(a = 6 × 10-7 m²/s) is initially at a uniform tempera-ture of 20°C and is well insulated along its lateral sur-face and at one end. At time t = 0, heat is applied tothe left boundary causing T, to increase linearly withtime at a rate of 1°C/s.ToT1T2T3TAL = 24 mm(a) Using the explicit method with Fo =;, derive thefinite-difference equations for nodes 1, 2, 3, and 4.(b) Format a table with headings of p, t(s), and thenodal temperatures T, to T4. Determine the surfacetemperature T when T35°C.

(a) We consider a control volume (CV) and study the heat transfer from and to this CV in a short…

A round solid cylinder made of a plastic material (a = 6 × 10-7 m³/s) is initially at a uniform tempera- ture of 20°C and is well insulated along its lateral sur- face and at one end. At time t = 0, heat is applied to the left boundary causing T, to increase linearly with time at a rate of 1°C/s.

A round solid cylinder made of a plastic material (a = 6 × 10-7 m³/s) is initially at a uniform tempera- ture of 20°C and is well insulated along its lateral sur- face and at one end. At time t = 0, heat is applied to the left boundary causing T, to increase linearly with time at a rate of 1°C/s.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

How much heat is conducted through a sheet of plate glass, k=0.0024 cal/cm2-sec-°C/cm, which is 2.0 meters by 3.0 meters and 5 mm thick, when the temperatures of the surfaces are 20 and -10°C? COMPLETE FBD SOLUTION AND REQUIREMENTS PS. THIS IS A HEAT TRANSFER PROBLEM
If the rate of heat flow through a furnace wall is 0.94 kW/m². The wall consisting of 0.20 m thick inner layer of chrome brick, a center layer of kaolin brick of 10.0 cm and an outer layer of masonry brick 100 mm thick, having a thermal conductivity of 1.25 W/m°C , 0.74x10ª kW/m°C_and 0.555x10³ kW/m°C respectively. The unit surface conductance at the inner surface is 74 W/m2 °C and the outer surface temperature is 70 °C . The temperature of the gases inside the furnace is 1670 °C , assume steady heat flow, Calculate the following: 1- The temperatures of the gases inside the furnace. 2- The interior surface temperature of the inner and outer layers.
How long should it take to boil an egg? Model the egg as a sphere with radius of 2.3 cm that has properties similar to water with a density of = 1000 kg/m3 and thermal conductivity of k = 0.606 Watts/(mC) and specific heat of c = 4182 J/(kg C). Suppose that an egg is fully cooked when the temperature at the center reaches 70 C. Initially the egg is taken out of the fridge at 4 C and placed in the boiling water at 100 C. Since the egg shell is very thin assume that it quickly reaches a temperature of 100 C. The protein in the egg effectively immobilizes the water so the heat conduction is purely conduction (no convection). Plot the temperature of the egg over time and use the data tooltip in MATLAB to make your conclusion on the time it takes to cook the egg in minutes.
Shown in the figure below is an insulated copper block that receives energy at a rate of 200 W from an embedded resistor. The temperature of the resistor is 34°C above the temperature of the copper block. Insulation Δt = Resistor 5000000000000000000000 oooooooooooooo....... Copper block If the block has a volume of 10-3 m³ and an initial temperature of 20°C, how long would it take, in minutes, for the temperature to reach 88°C? -V=10-³ m³ T₁ = 20°C min
Steaks (2 cm thick, k = 0.45 W/m - °C, « = 0.91 x 107 m2/s) usually have an original temperature of 25 °C. They will be cooled in a refrigeration room. The said room has a temperature of -11 °C. The heat transfer coefficient on both sides of the steak is 9 W/m2 - °C. How long will it take for both surfaces of the meat to be cooled to 2 °C? Assume the geometry of steaks to be a flat slab.
Q5: The piston cylinder device (radius =10 cm) contains a liquid with a pressure 100 kpa and temperature of 20 ° C and has a liquid convection heat coefficient =93 W m K-. Connect its fixed side to a cubic piece of aluminum (side length 15 cm) with a thermal conductivity coefficient of aluminum = 239 W m ' K 1. At the bottom of the aluminum piece there is a heat source with a temperature of 150 ° C, noting that the heat source is located in a vacuum chamber. Radiation thermal resistance 3.17 K/ W. Calculate the change in piston height during 1 sec. if you know that there is no change in the internal energy of the piston cylinder device. Note 1KWatt= 1KJ/s
Two flat infinite slabs, each 5 m thick, are each initially uniform in temperature, with one being at 0° and the other at 20°. At t=0, the two slabs are stacked together (the warmer one at larger y) and both the top and bottom surfaces of the stack are kept at 0°. Find the temperature in the stacked slabs as a function of y and t for t > 0. Write out the heat flow equation, find the general solution, and the specific solution for this arrangement.
Q5: The piston cylinder device (radius =10 cm) contains a liquid with a pressure 100 kpa and temperature of 20 ° C and has a liquid convection heat coefficient =93 W m 2 K. Connect its fixed side to a cubic piece of aluminum (side length 15 cm) with a thermal conductivity coefficient of aluminum = 239 W mK. At the bottom of the aluminum piece there is a heat source with a temperature of 150 ° C, noting that the heat source is located in a vacuum chamber. Radiation thermal resistance 3.17 K/ W. Calculate the change in piston height during 1 sec. if you know that there is no change in the internal energy of the piston cylinder device. Note 1KWatt= 1KJ/s
A rectangular slab with surface area 2m? and with thickness 20mm is exposed to hot gas on one side. 30 W of heat is transferred from the hot gas to the slab surface while the temperature at the opposite side is measured as 85°C. Which of the following boundary conditions is true for 1D under steady-state condition: O a dT - K 30W/m2; T1-85°C dx Ob. hA(AT)= 30W/ m² ; T1=85°C h(AT)= 15W/ m² ; T1=85°C Od q=30W; T1=85°C;
A stainless steel alloy has cylindrical shape (k = 25 W/m.oC), diameter is 10 cm and 25 cm long, taken to furnace. The initial temperature is 90 oC, the furnace temperature is 1260 oC and the heat transfer coefficient is h = 100 W/m2.oC. Determine the time required for a stainless steel alloy to reach 830 oC. Take thermal diffusivity (k⁄ρ c = 0.45 × 10−5 m2/s).
Its thickness is 1.18 m, its thermal conductivity is 2.75 W/m.°C and its surface area is 15m2Consider a wide plane wall. Inside of the base plateThere is a uniform heat flux produced on its surface with the help of the resistance wire inside.590 W/m2 on the left surface of the wall at x=0net heat fluxand the temperature on this surface was measured as 590 °C. On the wallassuming that there is no heat generation and that the thermal conductivity is constant;a) The differential equation for continuous one-dimensional heat conduction in the wall, andSet the boundary conditions.b) Solve the differential equation to obtain a relation for the temperature change at the wall.c) Calculate the heat loss rate from the wall.
Consider a large plane wall of thickness L = 0.4 m, thermal conductivity k=2.3 W/m °C, and surface area A= 20 m2. The left side of the wall at x= 0 is subjected of T1 = 80°C. while the right side losses heated by convection to the surrounding air at T∞=15 oC with a heat transfer coefficient of h=24 W/m2 oC . Assuming constant thermal conductivity and no heatgeneration in the wall, (a) express the differential equation and the boundary conditions forsteady one-dimensional heat conduction through the wall, (b) obtain a relation for thevariation of temperature in the wall by solving the differential equation, and (c) evaluate therate of heat transfer through the wall