A rectangular concrete slab, 4.a m. x 5.d m. is shown in Figure 3.5, rests on the surface of a soil mass. The load acting on the center of the slah is 1785KN. Determine: ' The soil stress just below the slab. ;) The vertical stress increase at point A. a. b. Plan A 4.5 m Cross Section 3.8 m A 3.1 m Figure 3.5 5.3 m

A rectangular concrete slab, 4.a m. x 5.d m. is shown in Figure 3.5, rests on the surface of a soil mass. The load acting on the center of the slah is 1785KN. Determine: ' The soil stress just below the slab. ;) The vertical stress increase at point A. a. b. Plan A 4.5 m Cross Section 3.8 m A 3.1 m Figure 3.5 5.3 m

Principles of Geotechnical Engineering (MindTap Course List)

9th Edition

ISBN:9781305970939

Author:Braja M. Das, Khaled Sobhan

Publisher:Braja M. Das, Khaled Sobhan

Chapter10: Stresses In A Soil Mass

Section: Chapter Questions

Problem 10.12P: Refer to Figure 10.43. A strip load of q = 1450 lb/ft2 is applied over a width with B = 48 ft....

See similar textbooks

Similar questions

Q4: For the soil element shown, compute the stresses acting on the plane inclined by 40° with the horizontal plane then draw Mohr circle and place the stresses with respect to O.P. 20kPa 35kPa 100kPa 300 40°
(c). The magnitude of stresses have been applied on soil element where Normal vertical stress is 120 KN/m2 , Normal horizontal stress is 300 KN/ m², shear stress is 40 KN/m² and Angle of internal friction is 20°. Find the Principle stress and Normal and Shear stress on plan AB, figure 1. Oy В it Ox Ox A Oy Fig .1 Solution: 1. 01.. . 2. 03.. . 3. On.. .4. Tn..
Situation 3: 200.02 kN 75.05 mm 50.05 mm 15.05 deg 200.02 kN 1. Tensile stress at section A-A 2. Shear stress at section A-A 3. What angle of plane A-A gives maximum shear stress?
A beam with breadth b = 300 mm and %3D depth d = 500 mm is pre stressed by an initial force of 700 kN. Total loss of %3D pre stress is 12.67%. 20. Calculate the resulting final compressive stress if the pre stressing force is applied at the centroid of the beam section. а. 4.67 MPа C. 7.94 MPa b. 4.08 MPa d. 9.21 MPa 21. Calculate the resulting final tensile stress if the pre stressing force is applied at an eccentricity of 150 mm below the centroid of the beam. b. 11.42 MPa d. 4.67 MPa а. 7.34 MPа с. 3.26 МРа Calculate the resulting final compressive stress if the pre stressing force is applied at an eccentricity of 150 mm below the centroid of the beam. 22. а. 7.34 МPа b. 11.42 MPa С. 3.26 МPа d. 4.67 MPa
Refer to Figure 10.43. A strip load of q = 1450 lb/ft2 is applied over a width with B = 48 ft. Determine the increase in vertical stress at point A located z = 21 ft below the surface. Given x = 28.8 ft. Figure 10.43
Solve Problem 7.8 using Eq. (7.29). Ignore the post-construction settlement. 7.8 Solve Problem 7.4 with Eq. (7.20). Ignore the correction factor for creep. For the unit weight of soil, use γ = 115 lb/ft3. 7.4 Figure 7.3 shows a foundation of 10 ft × 6.25 ft resting on a sand deposit. The net load per unit area at the level of the foundation, qo, is 3000 lb/ft2. For the sand, μs = 0.3, Es = 3200 lb/in.2, Df = 2.5 ft, and H = 32 ft. Assume that the foundation is rigid and determine the elastic settlement the foundation would undergo. Use Eqs. (7.4) and (7.12).
Figure 3 shows the stresses at failure for a point in a soil mass. Note A.U. (a) Draw the Mohr Circle for this point. (b) Determine the Pole Location. (c) Determine 01 and 03. (d) If the soil cohesion, c = 1.0, what is the friction angle of the soil, o? (e) Determine Tƒƒ and off. (f) What are the orientation of the failure planes, cr? 2 3 5 20° 51°
A rectangular concrete slab, 3m x 4.5m shown in Figure 05.12, rests on the surface of a soil mass. The load on the slab is 1620 kN.1.) Determine the soil stress below the slab2.) Determine the vertical stress increase at point A3.) Determine the vertical stress increase at point B.
The increase in stress under a corner of a rectangular loading is given by Boussinesq formula which is as follows:1. What is the increase in stress at point that is 2.5 meters beneath a corner of a 1.5 meter x 2 meter footing carrying a total uniform load of 75 kPa? a. 133.26 kPab. 229.23 kPac. 253.14 kPad. 211.25 kPa2. What is the increase in stress at point that is 2.5 meters beneath the center of a 3 meter x 4 meter footing carrying a total uniform load of 75 kPa? a. 916.94 kPab. 533.04 kPac. 245.50 kPad. 922.54 kPa3. What uniform load will produce an increase in stress of 36 kPa at point that is 2.5 meters beneath the center of a 3 meter x 4 meter footing? a. 7.504 kPab. 1.123 kPac. 2.945 kPad. 5.213 kPa
A circular Beam with roller joint R L y y oo = 298.6055 Pa Ro = 2.0649 m L = 61 m Material Data E[ GPA] Oyp [MPa] p [kg/m^3 V 200 0.3 700 7800 Find: Displacement in X, Y, Z direction, von misses stress, tresca stress, and triaxial stress at x = L, at x = L/2 and x = 0. Please show all work
9. In the figure shows a plan view of footing that applies a uniform load of 300kPa on a horizontal ground surface. Calculate the vertical stress component in kPa at point A at a depth of 2m. 7.0 m 2.0 m A 6.0 m 3.0 m (a) Fig P-97D A. 178 B. 182 C. 190 D. 186
QUESTION 1 Two vertical forces are applied to a beam of the cross section shown. i) ii) Determine the maximum tensile and compressive stresses in portion BC of the beam. Determine the maximum shear stress in the beam. 65 kN 65 kN 5mm/75 mm75 mm B D 150 mm 50 mm 1.5 m