Problem 3. Two reservoirs are connected by a pipe whose diameter is D=0.15 m and geometry asreported in figure 2. The difference in water (kinematic viscosity v =10“m²s', density p=1000Kg/m³) elevation (AH) between the two reservoirs is 8 m.a) Qualitatively sketch the Hydraulic Grade Line and the Energy Grade Line of the flow withinthe pipe.b) Compute the flow rate within the pipe assuming the equivalent sand roughness to be e=0.4mm.ΔΗ1m25m4m

Answered: Image /qna-images/answer/5aba2476-295f-4be7-b223-a8297ca0ec9d.jpg

Answered: a) Qualitatively sketch the Hydraulic…

a) Qualitatively sketch the Hydraulic Grade Line and the Energy Grade Line of the flow within the pipe. b) Compute the flow rate within the pipe assuming the equivalent sand roughness to be ɛ=0.4

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question 3 Consider 2 which shows a pipe system connecting two reservoirs. The pipe diameter changes at point B as shown in the image A 10 cm 23 m NOT TO SCALE Figure 2: 9 m 6 cm с 3 m 1. Describe what is referred to by the hydraulic gradient line and the energy gradient line. What is the difference between the two levels? In what scenario will the energy and hydraulic grade lines coincide? 2. Calculate the velocities in the two segments of the pipe. Take into account the friction losses through the pipe, entry loss to the pipe and the shock contraction losses at B. Take the pipe friction factor as 0.005 and the coefficient of contraction at B as 0.6. 3. Draw the energy gradient line and the hydraulic gradient line for the system.
2. Four reservoirs connection is shown below. Determine the discharges in each pipe using Manning's Equation withn = 0.012. Draw the final hydraulic gradient line (HGL). Diameter of pipe (m) Length of pipe (m) 1500 800 Pipe AX 0.30 BX 0.25 XY CY 400 0.30 500 0.20 DY 1600 0.20 WS ELEV. = 300 m wS ELEV. = 150 m WS ELEV. = 100 m ELEV. = 75 m WS D. Y
Problem 2 A sluice gate, which controls the flow rate in a channel by simply raising or lowering a vertical plate, is commonly used in irrigation systems. With reference to the figure below, consider VI≈ 0, yl-2.2 m and y2=0.7m. Assuming ideal fluid and steady state conditions, answer the following questions. Sluice gate a) Compute 12 b) 3/₁1 Assuming a unitary width of the channel, and a hydrostatic distribution of pressure right in front of the gate, compute the force acting on the gate itself (It is fine to estimate the submerged depth of the gate equal to yl-y2). J c) Assuming a unitary width of the channel, compute the force acting on the sluice gate using momentum balance principles. 1 d) Compare the values obtained from b) and c), why are they different in your opinion?
Three reservoirs are connected by a piping system as shown in Figure 1. Find the discharge into or from the reservoir B and C, if the rate of flow from reservoir A is (55+X) liter/s. Also find the height of water level in reservoir C. Assume the following data: Pipe 1 2 3 Length (m) 1X00 600 700 Diameter (mm) 400 300 200 Friction factor 0.008 0.008 0.008
Pipe in Parallel: Two pipes connect two reservoirs which a height difference of 10m. Pipe 1 has diameter 50mm and length 100m. Pipe 2 has diameter 100mm and length 100m. Take f= 0.008 then calculate: - a) Rate of flow for each pipe. b) The diameter D of a pipe 100m long that could replace the two pipe and provide the same flow. energy line H. h
I6 a) Determine the radial positions of a pitot tube for a 6-point traverse in a 0.3 m inner diameter pipe. Show your calculations. b) If the fluid velocity measured at the pipe center is 0.3 m/s and yields a Reynolds number based on local velocity of 4000, what is the fluid cross-sectional average velocity in the pipe? c) At what value of Re is the discharge coefficient of an orifice meter approximately independent of geometry and flow rate?
For a junction if pipe 1 diameter = 50 mm, mean velocity 2 m/s, pipe 2 diameter 40 mm takes 30% of total discharge and pipe 3 diameter 60 mm. Find the discharge in I/hr and velocity through each pipe? Comments on the results.
Problem 5: Pipe Flow A 10,000 ft P BC 20,000 ft D This semester we worked through several versions of the pipe flow problem sketched above, in which a 3.0 ft diameter pipe is used to convey water from reservoir A (surface elevation 80 ft) to reservoir D (surface elevation 90 ft). In week 14, we considered a specific example with a cast iron pipe (A = 0.00085 ft), flow rate of Q=40 ft³/s, and average velocity of V = 5.66 ft/s. For these conditions, the friction factor was λ = 0.015 and the pump added 86 ft of head. Assume the water temperature is always 60°F. Part A Assuming the pump is 75% efficient and electricity costs 10e/kW.hr, how much will it cost to run this pump for a year? Hint, 1 kW hr = (1000 watts) (1 hr) = (1000 J/s)(3600 s) = 3.6x106 J. Part B Now let us assume we need to double the discharge to Q = 80 ft³/s, but unlike the example in week 13, we are not going to make the false assumption that the friction factor λ is constant. You may, however, assume that the roughness…
After analyzing the flow type in a refinery oil (s = 0.8, v= 1.94x10-4 ft2/s) flowing through a 9inch diameter pipe at (41/1000) ft3/s. Find the following a)centerline velocity b)the velocity at r = 2inch c)the frictional factor d)the shear stress at the pipe wall and e)the head loss per foot of pipe length.
Flow Speed in a Channel The speed of water flowing in achannel, such as a canal or river bed, is governed by theManning Equation,
49. Water flows at a rate of 200 GPM into a piping system connected in series. Length, diameter, and loss coefficient of each pipe are given below. For p= 62.4 Ibm/ft and u = 0.7E–3 lbm ft/s find total pressure drop and the diameter of an equivalent pipe representing this system. C) Fluid Power Theory an.. IndPitEn IlIb. Fluid Mechanics: Incompressible Viscous Flow 392 Pipe D K No. (ft) 100.00 (in) 5.00 (-) 50.00 1 2 80.00 4.50 45.00 3 70.00 4.00 65.00 4 120.00 3.50 55.00 5 90.00 3.00 15.00
Please solve both parts correctly. A pipe that carries water, has section of radius r₁ = 12 cm; it is narrowed, so the section has radius r2 = 6 cm. Calculate a) If the difference between pressures is 7.5 kPa, what is the velocity in section "2" ? b) the flow rate of the duct.