A pump 254 mm suction pipe and a 127 mm discharge pipe is used to deliver 52 L/s of water. The suction gage reads 15.6 kPa vacuum and the discharge gage located 100 cm above the suction gage which  reads reads 108 kPa gage. Determine the following: 1. The total dynamic head in meter 2. The water power in kW 3. The motor horsepower if the pump efficiency is 76% Choices: 1.  13.856 14. 495 14.409 2. 7.631 7.348 8. 245 3. 12.960 14.935 13.935

Q: in an absorption type refrigerator, the heat is supplied to NH, generator by condensing steam at I b...

A: Given:Evaporator temperature, Te=-5o C or 268 KCondensor temperature, Tc=27o C or 300 KSteam pressur...

Q: Calculate the position of the resultant load from point A in meters.

A: W1= 6 N/m W2= 12 N/m

Q: When a viscous, incompressible fluid enters a pipe of radius, R, its velocity is uniform and of magn...

A:

Q: At a temperature of 80°C, a steel tire 12 mm thick and 90 mm wide that is to be shrunk onto a locomo...

A: Given Data: Initial temperature, T1=80 C Final temperature, T2=25 C

Q: The force system shown consists of four forces. If P is 400 kN and Q is 450 kN

A:

Q: Determine the x-component of R (in Ib). *

A:

Q: Q 4.9

A: the explanation for question 4.9

Q: 1. An ideal vapor-compression refrigeration cycle with refrigerant-134a, with 0.125 kg/s, as the wor...

A:

Q: TRUE OR FALSE The continuum concept in hydraulics assumes that a fluid often behaves as if itwere co...

A: It is true that the continuum concept in hydraulics assume that a fluid often behaves as if it were ...

Q: Determine the diameter of a droplet of water in mm if the pressure inside is to be greater than that...

A: Given data,  σ= 7.26 *10-2  P= 130 N/m²  Diameter of droplet is required

Q: Consider the sealed containers (same fluid and on the same ground level) below with heights given in...

A: Pressure = Weight Density of fluid X Height of fluid      

Q: TRUE or FALSE. Please provide a quick explanation thanks! 1. Each molecule of a system has a certai...

A: Statement 1 is True.  Each molecule of a system has a certain quantity of mass, thermal energy, or m...

Q: In a steam power plant, the condenser pressure is 10 kPa. The turbine and pump isentropic efficienc...

A:

Q: Write a brief procedure for measuring the vapor pressure of water

A:

Q: A multi plate clutches an included angle of 90°. A multi plate clutch, has 2 discs the driving shaft...

A:

Q: The 65-mm-diameter A992 steel shaft is subjected to the torques shown where T = 650 N-m. %3D 400 N-m...

A: Answer: The angle of twist of the end A is 7.875 × 10-3 radians or 0.451°.

Q: Quo 2.11. Design the longitudinal and circumferential joint for a boiler whose diameteris 2.4 meter ...

A: Given data,P=1 N/mm2D=2.4mηL=85%(triple riveted butt joint)ηC=70%(double riveted lap joint)σt Tensil...

Q: A body is launched with speed 45m. s¬' from point A at angle -1 0 = 60° to the horizontal, landing a...

A:

Q: A composite beam is made of two brass [E = 112 GPa] plates bonded to an aluminum [E = 64 GPa] bar, a...

A:

Q: Determine the Moment of Force F (10ON) shown in fig. down about point (A) by 2 ways at least? 12m

A:

Q: Reynolds number of the flow.

A: Given; Water flows through a pipe having an inner radius;  R=20mmDiameter:d=2r=2×20=40mm=0.04mTemper...

Q: 5500 kg of steam is produced per hour at a pressure of 7.6 bar in a boiler with dryness fraction 0.9...

A: GIVEN DATA - Mass M=5500kg/hr BOILER PRESSURE =7.6bar DRYNESS FRACTION X=0.98 FEED WATER TEMPRATURE ...

Q: Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the ...

A:

Q: eam and the moment diagram. I will really upvote. Thanks

A: given:

Q: A weight of 18N is supported by a linear spring having a stiffness of 4 N/m and a dashpot having a d...

A:

Q: The motion of a body travelling along the x-axis is plotted in the graph below. What is the distance...

A:

Q: Q1: Determine the Moment of Force F (100N) shown in fig. down about point (A) by 2 ways at least

A:

Q: What is the specific gravity of the following gas? Component Partial pressure, psia Methane 17.8 Eth...

A:

Q: The pump takes water from an open tank below the pump centerline. Determine the maximum static eleva...

A: Write the given data. H=1500 ftPsat=0.69 psiav=0.01608 ft3/lb

Q: The stream function o in a two-dimensional flow field is given as p = 4x – 3y + 7xy (a) Prove that t...

A:  

Q: a 12" diameter pipe carries oil with a velocity distribution of v = 9(r1^2 - r^2) determine the aver...

A: Assuming laminar flow , diameter of the pipe = 12 inch radius=R= 6 inch velocity distribution= v= 9(...

Q: Calculate the principal stresses to the given state. Calculate the angle of rotation in the x-y plan...

A:

Q: A happy heat-loving bug is wandering on a hot plate. The temperature at any point on the plate is gi...

A:

Q: A 1-lb collar is attached to a spring and slides without friction along a circular rod in a vertical...

A:

Q: The force system shown consists of four forces. If P is 400 kN and Q is 450 kN.

A:

Q: Two distributed loads act on the beam AB. If the resultant of this loads is a 2400 N-m counterclockw...

A:

Q: 8. Determine the power rating of a no. 60 chaln, single- strand, operating on a 20-tooth sprocket at...

A:

Q: Calculate the fraction of atom sites tha

A: Need to find fraction of atom site.

Q: y E,I L A cantilever beam with distributed lateral load p as shown above. Given: The deflection and ...

A: since there is only one element, the element matrix equation is same as global matrix equation, Elem...

Q: Water in a piston/cylinder arrangement is at 150 psia and 900 °F, as shown in Fig. C. There are two ...

A: Given data, State 1:- When the piston is in upper stops Pressure at state 1, P1 = 150 psia Temperatu...

Q: Why materials like glass, cork and cracked stainless steel mixing device are not suitable to be used...

A: Stainless steel has a crystalline nature While glass and cork are amorphous solids.  

Q: A centrifugal pump draws water from a 38cm pipe from an open reservoir in which the water surface is...

A:

Q: A motorcyclist in a circus rides his motorcycle within the confines of the hollow sphere. The coeffi...

A: Answer: The minimum speed at which he must travel if he is to ride along the wall when θ = 90° is 19...

Q: A transmission shaft of ultimate strength, S= 600 N/mm' and yield strength. S 400 N/mm2 is subjected...

A:

Q: A machine member is subjected to fluctuating stress O =0, cos(8 t). The endurance limit of the mater...

A: GIVEN DATA - σ=σo cos(8πt) σe=350MPa FACTOR OF SAFETY N=3.5 WE HAVE TO FIND VALYE OF ALLOWABLE STRES...

Q: 3. You wish to lift a 12,000 lb stone by a vertical distance of 15 ft. Unfortunately, you can only g...

A: NOTE:- As per our company guidelines we are supposed to answer only one question. Kindly repost othe...

Q: Consider a 210-MW steam power plant that operates on a simple ideal Rankine cycle. Steam enters the ...

A:

Q: Q1: Determine the Moment of Force F (100N) shown in fig. down about point (A) by 2 ways 05 m

A: Calculated moment of force F about point A.

Q: 5. A heat engine release heat into the cold reservoir at 500 K with a carnot efficiency of 25 %. Wha...

A: Given data: Carnot engine with cold reservoir at 500 K has an efficiency = 25%  

Q: A component in a refrigeration system is the evaporator. It is here that the cold refrigerant picks ...

A:

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.