A power plant is being built that will deliver 400 kW at 67,000 V using an iron cable with a resistance of 0.084 2. The cable will have a cross-sectional area of 0.009 m². Determthe cable's length and the power loss of the cable.MaterialAluminumCopperGoldPlatinumSilverTungstenResistivity(m)2.65 x 1081.68 x 102.44 x 10-89.71 x 10810.6 x 1081.59 x 1085.60 x 108L=power loss

Given data as per the question Power to deliver =400 kwvoltage =67000 vResistance=0.084ΩArea=0.009…

A power plant is being built that will deliver 400 kW at 67,000 V using an iron cable with a resistance of 0.084 2. The cable will have a cross-sectional area of 0.009 m² Deter the cable's length and the power loss of the cable. Material Aluminum Copper Gold Platinum Tungsten Resistivity (Q-m) 2.65 x 108 1.68x10 2.44 x 10 9.71 x 10 10.6 x 108 1.59 x 10 5.60 x 108 L- power loss

A power plant is being built that will deliver 400 kW at 67,000 V using an iron cable with a resistance of 0.084 2. The cable will have a cross-sectional area of 0.009 m² Deter the cable's length and the power loss of the cable. Material Aluminum Copper Gold Platinum Tungsten Resistivity (Q-m) 2.65 x 108 1.68x10 2.44 x 10 9.71 x 10 10.6 x 108 1.59 x 10 5.60 x 108 L- power loss

College Physics

1st Edition

ISBN:9781938168000

Author:Paul Peter Urone, Roger Hinrichs

Publisher:Paul Peter Urone, Roger Hinrichs

Chapter20: Electric Current, Resistance, And Ohm's Law

Section: Chapter Questions

Problem 58PE: -gauge copper wire has a diameter of 9.266 mm. Calculate the power loss in a kilometer of such wire...

See similar textbooks

Similar questions

Integrated Concepts (a) What energy is dissipated by a lightning bolt having a 20,000-A current, a voltage of 1.00102 MV, and a length of 1.00 ms? (b) What mass of tree sap could be raised from 18.0°C to its boiling point and then evaporated by this energy, assuming sap has the same thermal characteristics as water?
_1. If wire has 1.25 x 1016 electrons flowing through its cross-section in one second, what is the current in the wire. 2. How much current is flowing when 15 C pass a specified point in 5 s? 3. An electric motor winding uses 180 m of copper conductor with a cross-sectional area of 0.26 cm2. Find the resistance of the electric winding at 20°C. The resistivity of copper is 1.72 x 10-8 Q-m. 4. What is the resistance of a lamp which allows 0.8 A current when 110.0 V is applied to it? 5. The heating element in a clothes dryer is rated at 5 Kw and 220 V. How much current does it draw? 6. A potential difference of 9 V is maintained across a conductor in a circuit. If the conductor has a resistance of 10 ohms, how many electrons flow through the conductor's cross-section in 5 seconds? 7. A piece of material with a square cross-section measuring 1 mm on each side has a length of 1 m. What is the resistance of this material if it were made of aluminium? Fused quartz? Finally, calculate the…
What is the maximum power deliverable by a stack of 100 10YSZ cells to an optimum resistive load? Given each cell has open circuit voltage of 1.1V in series and the resistance is 17.78 ohms. The dimensions of the 10YSZ electrolyte are 0.1m x 0.1m x .0002m.
A wire 1.3m long and a cross-sectional area of 0.390mm^2 has a resistance of 33.9ohms at 20degreesC. If the resistance of the wire increases to 39.7ohms at 28.6degreesC, what is the temp coefficient of resistivity for the wire? - .01989 - .0170 - .674 - .0409 - .0350
Integrated Concepts. A 12.0-V emf automobile battery has a terminal voltage of 16.0 V when being charged by a current of 10.0 A. At what rate (in oC/min ) will its temperature increase if its mass is20.0 kg and it has a specific heat of 0.300 kcal/kg. oC, assuming no heat escapes?
The resistivity of a 1.0 m long wire is 1.72 x 10-8pm and its cross sectional area is 2.0 X 10-6m2. If the wire carries a current of 0.20 A, what is the voltage across the wire? 17 mv 0.90 mv 1.7 mv 10 mv
=9634 Given that the delivered power to a resistor is equal to P when the current flowing in the resistor is la If the current increased to 8.3 la, the delivered power to the resistor will be: Select one: OA. 8.3 P OB. 16.6 P OC. 1378 P OD.0.1P OE 68.9 P Next page 901 PM 4ENG 4/30/2021 Prise Inser Delete FIL 10 Num Lock Backspace 本 6 17 V 12 7 8 9. T. Home Pyup 1 GYH J -IK IL 4 Enter 1 Shift 3 B YN M End Pon 01 AlH Crl Ins Home PgOn End
A particular wire has a resistivity of 1.5 x 10sn- m and a cross-sectional area of 2.5 x 106 m2. A length of this wire is to be used as a resistor that will receive 43 W of power when connected across a 20-V battery. What length of wire is required? km
What current flows through a 2.45-cm-diameter rod of pure silicon that is 21.5 cm long, when 1.00 x 10³ V is applied to it? (Such a rod may be used to make nuclear particle detectors, for example.) 0.000877 X A
1. What current flows through a 0.50 mm diameter rod of annealed Copper that is 90.0 cm long, when 12 V is applied to it? Resistance of the annealed Copper = Current flowing through the annealed Copper = A [3 marks] Resistivity p Material (ohm m) Silver 1.59 x 10-8 Copper 1.68 x10-8 Copper, annealed 1.72 x10-8 Aluminum 2.65 x10-8 Tungsten 5.6 x10-8 Iron 9.71 x10-8 Platinum 10.6 x10-8 Manganin 48.2 x10-8 Lead 22 x10-8
2. A = area -L = length - Calculate the resisitance per unit length of a Nichrome wire of a. |=-W Radius 0.321mm. (Resistivity Nichrome= 150x10* Q.m) p = resistivity of R b. If a potential differnces of 10 V is maintained across a 1 m length of the Nichrome wire, what is the current in the wire? 4.00 kO
43 – 44. What is the resistance of an aluminum wire of length 10 m and cross-sectional area of 0.002 m2 ? The resistivity of aluminum is 2.65 x 10-8 N m. O 1.325 x 1042 O 1.325 x 10-12 2 O 1.325 x 10-8 2 O 1.325 x 109