A PMMC instrument has internal resistance of 0.51 kN and gives full scale deflection for 41 mA. The required resistance value of multiplier resistors for employing the meter as a multi range voltmeter for voltage range 56 V will be ohms. O a. 222.14 O b. 136.08 O c. 109762.92 O d. 855.85

A PMMC instrument has internal resistance of 0.51 kN and gives full scale deflection for 41 mA. The required resistance value of multiplier resistors for employing the meter as a multi range voltmeter for voltage range 56 V will be ohms. O a. 222.14 O b. 136.08 O c. 109762.92 O d. 855.85

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Q1.Three-phase half wave rectifier supply resistive load with DC power of 4 kW; the ammeter…

A: Given Power = 4 kW Frequency = 50 Hz I = 8 A

Q: / The resistance of a platirum thermometer wire measured at 50C°, 200C° and 500C° is 14,20320 ,…

A: Given,When a platinum thermometer wire is measured, At 50°C,The resistance is 14.2032 Ω.At 200°C,The…

Q: For the ideal-diode clipper circuit given below, VS = 12.sinωt V. Determine the output voltage Vout…

A: 1) Voltage at x or y determines the operation of diodes. For the diode D2 to be operated in Forward…

Q: A half-wave rectifier with ohmic load given in the figure below feeds a 50 2 load and the peak value…

A: Half wave Rectifier Load resistance 50ohm Peak value of source resistance 311V Frequency 50Hz

Q: Q4: An AC voltmeter uses the circuit below. The meter has an internal resistance of 1000 and…

Q: A semiconductor substrate of 1 mm2 cross section is used to design a resistor. The doped-p…

A: A semiconductor substrate of 1 mm2 cross-section is used to design a resistor. The doped p…

Q: Electrical Engineering Why we use Ag/A9CL electrode for recording and why we use Pt electrode for…

Q: Q1: Two diodes are required to handle a source voltage of 8kV with I-V performance shown below... 1.…

A: Diode is a terminal p-n junction semiconductor device. It has one p-n junction formed by alloying,…

Q: A single phase bridge rectifier supplied from a 120V - 50 Hz sinusoidal source is connected to an…

Q: 05: Determine the peak output voltage Vp(out) for the bridge rectifier in Fig. belowAssuming the…

A: The diodes are made of semiconductor materials. Silicon and germanium are common semiconductors for…

Q: 7 Item 4: The zener diode shown in the figure has VZ = 20 V. The voltage across the load stays a 20…

Q: A storage battery of internal resistance of 0.4 is to be charged from a DC line. If the EMF of the…

A: Given: Internal resistance, r=0.4ΩEMF of the battery, E=12VCharging current, I=4ALet DC supply…

Q: O A) A rectifiers shown in fig.3. If the output current assumed to be ripple free. (a) Draw the…

A: Note: We have solved the questions first part (a) for firing angle of 45 degree

Q: 9. Which of the following equation represents mass action law for semiconductors in electronic…

A: Let n be the electron concentration and p be the hole concentration after Adding impurities. And ni…

Q: From the image provide find A) what is the emf and show the loops/junctions used. B) What is the…

Q: Q2: The zener diode shown below has Vz= 18 V. The voltage across the load stays at 18 V as long as…

A: Given data The zener diode voltage Vz= 18 V. The voltage across the load stays VL= 18 V Iz is…

Q: Q3/A packet of resistors bought in an electronics component shop gives the nominal resistance value…

A: Tolerance in a resistance gives the maximum and minimum resistance variation in the Resistor. Less…

Q: A full-wave rectifier operating from the 60-Hz ac supply produces a 20-V peak rectified voltage. If…

A: For a full-wave rectifier,The given parameters are,f=60 HzVDC=20 VC=200 μFI=120 mA

Q: If we were to connect a voltmeter directly to an ohmmeter, what would you expect to see the ohmmeter…

A: The explanation is as follows.

Q: ld1_AMS. DI A 300 p3. A A .... .... ... DS Rioad

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: Q1.Three-phase half wave rectifier supply resistive load with DC power of 4 kW; the ammeter…

A: Note:Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for…

Q: A single-phase full-wave rectifier, energized from a 220 Vrms, 50 Hz ac source, supplies power to an…

A: Because In the highly Inductive Load (L/R is high) load current is constant at the Io and the diode…

Q: 2. An AC voltmeter uses a bridge rectifier with silicon diodes and a PMMC instrument with FSD = 75…

A: GIVEN DATA:

Q: Q5: Derive the expression for power P = VI in an electrical circuit. Q6: What is the resistance of…

A: 5) From Ohm’s law, we know that ⇒I=VRPower in a circuit is the amount of work done by the circuit in…

Q: Q4. A PMMC instrument with FSD of 150 µA and a coil resistance of 1.5 k2 is to be converted into a…

Q: Problem Solving 1. Bridge type power supply uses 4 rectifiers of Silicon type, During positive half…

A: Given: Full-wave bridge-type rectifier. Required: Output Voltage of bridge-type rectifier.

Q: As an electric drivetrain engineer, how do you design the battery pack to meet the requirement of…

A: The electrification done in the drive train enables the powertrain to enable mobility that is free…

Q: For mt mosfet n the carcuit shoun; Kp= 10 mA/VZ Vrel =1V %3D What is the înput resistance ?

Q: ii) Draw the cross-section of this p-n junction and show the depletion region and the corresponding…

Q: Consider the two devices shaun below which are fabricated from the semiconductor material. same i)…

A: In n type material, the excess charge carriers are electrons.In first device current doesn't flow if…

Q: Q5 / The resistance of a platirum thermometer wire measured at 50C°, 200C° and 500C° is 14,20322 ,…

Q: For the below shown rectifier configuration, find the expression for the average value of voltage…

A: Given circuit is of full wave controlled rectifier containing resistive load.

Q: Diodes D1 and D2 are Silicon with forward voltages of 0.7 volts. Vi and Vo are the circuit's input…

A: The conduction of diode can be validated by using the voltage divider rule to node V1 and with that…

Q: a) Calculate and plot the current flowing through the pn junctions of device #2 on your 3311 wafer…

A: Hello. Since your question has multiple sub-parts, we will solve the first three sub-parts for you.…

Q: 1 What is the standard Deviation ? Describe a scenario in which you would use each by given an…

A: We’ll answer the first question since the exact one wasn’t specified. Please submit a new question…

Q: ell + Vde 24 v Vs(t) - 120 V RM Problem 1: Given the half-wave rectifier with the DC source above a)…

A: NOTE:- As per our company guidelines we are supposed to answer ?️only first 3️⃣ sub-parts. Kindly…

Q: We have all undoubtedly experienced a loss of electrical power in our office or our home. When this…

Q: diode whose internal resistance is 20 ohms is to supply power to a 1000-ohm load from a 110V(rms)…

Q: Q2: State and explain Paschen's law. How do you account for the minimum voltage for breakdown under…

A: Breakdown voltage is a voltage at which the electric arc between two electrodes in gas is produced.…

Q: 2000 2000 200 Vs Figure Q3(a)

A: Given: Brief description: In the above given system they want to know the transfer function of the…

Q: In an Ohm's Law experiment that is performed by two resistors of resistances 20(2 and 30:2, the…

A: Current obtained is minimum. But potential difference applied is same. From ohm's law we know that…

Q: Question 3) An ohmic loaded half-wave controlled rectifier given in the figure below feeds a 25 Q…

A: Note: According to our policy i am providing solutions to the first three questions only. Given…

Q: Q 3/ We measured the current that appeared on the drawn screen as shown in the figure by using three…

A: Here,the three different current gauges are connected in series and they are, 1. De-Arsenval type 2.…

Q: A half-wave rectifier is needed to supply 15-V dc to a load that draws an average current of 300 mA.…

A: Given, Half wave rectifier having Average load current, IL=300 mA Peak to peak ripple required,…

Q: QJ. Draw the output voltage waveform for each circuit including the voltage values. (Ideal model) .…

A: For first circuit , during positive half cycle diode D1 conducts and D2 is reversed biased hence…

Q: b) Consider a Wheatstone bridge circuit (Figure 1) that has all resistances equal to 250 ?. The…

Concept explainers

Electrical Heating Unit

The conversion of electrical energy to heat energy is known as electric heating. The heating system that converts the electrical energy to heat energy for various application is called electrical heating unit. Electricity is employed as the firing mechanism in electric heating systems, which transforms electric current to heat. Electric heaters have heating elements in the form of electric resistors.

Question

A PMMC instrument has internal resistance of 0.51 kN and gives
full scale deflection for 41 mA. The required resistance value of
multiplier resistors for employing the meter as a multi range
voltmeter for voltage range 56 V will be,
ohms.
O a. 222.14
O b. 136.08
O c. 109762.92
O d. 855.85

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Introduction

VIEW

Solution

VIEW

Step by step

Solved in 2 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

PROBLEM: The diode (blue line) should be at -10V not -8V SOFTWARE USED: LTspice XVII---Figure 1 is my work, and figure 2 is the correct sample. Please tell me what I did wrong. Thank you :))---Below is the .asc filehttps://www.mediafire.com/file/zxauoh86zi79nfu/EXPERIMENT_01.asc/file
The voltage signal coming out of the capacitor is with small ripples compare to the voltage signal out of the diode. True False
Full-wave rectified sine wave circuit is used to measure the RMS value of a half square wave with the help of PMMC meter. The meter was actually calibrated for sine wave. The circuit uses a meter movement with a full scale deflection current of 200uA and internal meter resistance of 5kΩ. Assuming Non-ideal diodes having resistance 1kΩ, Analyze the circuit to determine the value of series multiplier resister and the corrected RMS voltage, if meter is to read 225V RMS full-scale.
After replacing R5 with diode IN4007 (switch K3 to diode side) .What conclusion can you draw from analysis of this step ?
Draw a voltage multiplier(6 times) with half wave voltage doubler and discuss it generally..
The nominal PIV of the diodes in the figure is reduced, the current through RL is:(a) increases (b) decreases (c) does not change.
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Va.. (t) 10 kO 8V 10 kO Vin Vin(t) D2 Vout(t) RL Ims D1 6V -8V 4V Page | 1
Which of the following circuit elements is a typical example of semiconductor material? Lütfen birini seçin: O A. Capacitor O B. Inductor O C. Resistor O D. npn BJT O E. Voltage source
Power supply circuit is delivering 0.5 A and an average voltage 20 V to the load as shown in the circuit below. The ripple voltage of the half wave rectifier is 0.5 V and the diode is represented using constant voltage model. The smoothing capacitor value is equal to IL-DC =0:5A RL VL-DC =20V 220V omsb O 001 F O 0.02 F O 0.0167F O None of the above Activate
A clipper circuit based on diodes are simple way to modify waveform in mechatronics. Assume that the two diodes shown in the circuit below are ideal diodes. If the input voltage in the circuit is a 1 kHz sinusoid with peak amplitude of 8V, sketch the Vaue (t). 10 k. 8V 10 kN. D2 RL Vourlt) Vin= Vin(t) Ims D1 6V -8V 4V Page | 1
I ln. l. . :D docs.google.com/forms/d/e/1l Diode clippers are wave-shaping circuits in that they are not used to prevent signal voltage from going above or below certain * .levels TO F like that of the clipper, the shape of the .input signals of a clamper is changed F The clamping circuit clamps or shift the * .input sinusoidal signal up or down FO II
Using a positive Clamper Circuit, with an AC voltage of Vi = 13v with a frequency of 60hz, a value of 100u for the Capacitor, a silicon diode and a resistor with the value of 1000 ohms. Find the voltage value on the resistor at a simulation of 20ms. 2Vm Vm Vm Vo -Vm Input Waveform Output Waveform Positive Clamper circuit