A plate with width of 300 millimeters and thickness of 20 millimeters is to be connected to two plates of the same width with half the thickness by 25 millimeters diameter rivets, as shown. The rivet holes have a diameter 2 millimeters larger than the rivet diameter. The plate is A36 steel with yield strength F,- 248 MPa Allowable tensile stress on net area is 0.60F, and allowable bearing stress of 1.35F, The rivets are AS02, Grade 2, hot-driven rivets with allowable shear stress of 150 MPa. See Figure 2-11. 4) Determine the maximum load that can be applied to the connection without exceeding the allowable tensile stress in the plates: b) Determine the maximum load that can be applied to the connection without exceeding the allowable shear stress in the rivets: ) Determine the maximum load that can be applied to the connection without exceeding the allowable bearing stress between the plate and the rivets: P/2 Figure 2-11

A plate with width of 300 millimeters and thickness of 20 millimeters is to be connected to two plates of the same width with half the thickness by 25 millimeters diameter rivets, as shown. The rivet holes have a diameter 2 millimeters larger than the rivet diameter. The plate is A36 steel with yield strength F,- 248 MPa Allowable tensile stress on net area is 0.60F, and allowable bearing stress of 1.35F, The rivets are AS02, Grade 2, hot-driven rivets with allowable shear stress of 150 MPa. See Figure 2-11. 4) Determine the maximum load that can be applied to the connection without exceeding the allowable tensile stress in the plates: b) Determine the maximum load that can be applied to the connection without exceeding the allowable shear stress in the rivets: ) Determine the maximum load that can be applied to the connection without exceeding the allowable bearing stress between the plate and the rivets: P/2 Figure 2-11

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter5: Beams

Section: Chapter Questions

Problem 5.2.1P

See similar textbooks

Similar questions

Determine the design tensile strength of the plate (200 × 100) mm connected to a 12 mm thick gussets, using 20 mm bolts shown below, if the yield and ultimate stress of the steel used are 250 MPa and 420 MPa respectively, fy= 250 MPa fu= 450 MPa
Situation 5. The angular section shown below is welded to a 12 mm gusset plate. Both materials are A36 steel with Fy = 250 MPa. The allowable tensile stress is 0.6Fy. The weld is E80 Electrode and 12 mm thickness. INNOVATIONS Properties of L 150x90x12: y = 50 shear stress of weld = 0.3Fu A = 2750 Allowable REVIEW INNOVATIE a K ➜ www A. 234 KN B. 349 KN b 13. What is the value of P without exceeding the allowable tensile the angle? C. 382 kN p. 413 kN 14. Find required length of the weld based on shear? A. 280 mm C. 300 mm D. 380 mm B. 320 mm 15. Find the required value of a? A. 108 mm B. 97.9 mm D. 185 mm NEW INNOVATIONS REVIEW INNOVATIOf REVIEW NEW INNOVATIONS
What is the axial stress in the bronze rod (in MPa)? 2m 3m 6o kN mm 15mm banzerod
Determine the design tensile strength of plate (200x8 mm) connected to 10-mm thick gusset using 20 mm bolts as shown in the figure, if the yield and the ultimate stress of the steel used are 250 MPa and 410 MPa, respectively. Add 1mm around the bolt for the hole. Use LRFD method. Plate 8-mm thick 2 3 40+ 30 301 T 200 mm Gusset 10-mm thick 3af 30 2_3 *40 40+ 50,54 +40
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. plate: fy = 241 mpa fu = 4141 mpa rivet: fv = 152 mpa a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivets
An A36 steel plate with width of 400 mm and thickness of 12 mm is to beconnected to a plate of the same width and thickness by 34 mm diametersbolts, as shown in the figure (next slide). The holes are 2 mm larger thanthe bolt diameter. The yield strength of the steel plate is Fy = 248 MPa.Assume allowable tensile stress on net area is 0.60Fy. It is required todetermine the value of b such that the net width along bolts 1-2-3-4 isequal to the net width along bolts 1-2-4.a. Calculate the value of b in mm.b. Calculate the value of the net area for tension in plates in mm².c. Calculate the value of P so that the allowable tensile stress on net areawill not be exceeded.(Use at least 2 decimal points on your answers.)
4.) A 150 x 90 x 12 angular section is welded to a gusset plate as shown in the figure. The angle is A36 steel with FY=248 MPa. The weld is E 80 electrode with Fu = 550 MPa. The allowable tensile stress for the angle is 0.6Fy and the allowable shear stress for the weld is 0.3Fu. The Area of the angular section is 2751 sq.mm. with y=51mm. CS 56 Which of the following most nearly gives the design force P? a.) 400,365.9 N b.) 409,348.8 N c.) 412,793.5 N d.) 420,366.6 N 5.) A W350 x 90 steel is used as a simply supported beam 8m long. The beam carries three equal concentrated loads at every quarter points. It also carries a uniform dead load o 5 kn/m (including its own weight) and a uniform live load of 7.20 kn/m. Properties of W 350 x 90 steel: bf = 250 mm The allowable bending stress is 0.66Fy. The allowable shear stress is 0.40Fy. The allowable deflection is L/360. Use Fx=248 Mpa and E=200 Gpa. tf = 16.40 mm V d = 350 mm Determine the maximum value of each concentrated load based on…
2- The Tensile stress of AISI 1035 Cold-drawn steel is; (a) 550 MPa. (b) 500 MPa. (c) 450 MPa.
1.12 A fillet-welded joint of 6 mm size is shown in the figure. The welded surfaces meet at 60-90 degree and permissible stress in the fillet weld is 108 MPa. The safe load that can be transmitted by the joint is 100 mm F F 810 50mm
Topic:Bolted Steel Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A 12.5 mm x150 mm plate is connected to a gusset plate having a thickness of 9.5 mm.Diameter of bolt = 20 mm Both the tension member and the gusset plate are of A 36 steel. Fy = 248 MPa, FU = 400 MPa. Shear stress of bolt Fnv = 300MPa. Questions: a.Determine the shear strength of the connection. b.Determine the bearing strength of the connection. c. Determine the block shear strength of the connection.
ISA 100 x 100 x 10mm (Cross sectional area = 1908mm2) serves as tensile member. This angle is welded to a gusset plate along A and B appropriately as shown. Assuming the yield strength of the steel to be 260 N/mm2 the tensile strength of the member can be taken to be approximately A ISA 100x100×10 Gusset Plate B
Determine the tensile strength of the welded A992 WT4×20. WT4× 20 PL – Transverse weld