A plate that is 250 mm wide and 25 mm thick is to be reduced in a single pass in a two-high rolling mill to a thickness of 20 mm. The roll has a radius = 500 mm, and its speed = 30 m/min. The work material has a strength coefficient = 240 MPa and a strain hardening exponent = 0.2. Determine (a)roll force, (b) roll torque, and (c) power required to accomplish this .operation 1365 N & 529865 N-m & 452 W O 500250 N & 12005 N-m & 2456 W O 71254632 N & 135674 N-m & 12053 W O 1851829 N & 46296 N-m & 92,591 W O

A plate that is 250 mm wide and 25 mm thick is to be reduced in a single pass in a two-high rolling mill to a thickness of 20 mm. The roll has a radius = 500 mm, and its speed = 30 m/min. The work material has a strength coefficient = 240 MPa and a strain hardening exponent = 0.2. Determine (a)roll force, (b) roll torque, and (c) power required to accomplish this .operation 1365 N & 529865 N-m & 452 W O 500250 N & 12005 N-m & 2456 W O 71254632 N & 135674 N-m & 12053 W O 1851829 N & 46296 N-m & 92,591 W O

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

A wire is drawn through a draw die with an entry angle = 15o. The starting diameter is 0.100 in. And the final diameter = 0.080 in. The coefficient of friction at the work-given interface = 0.07. The metal has a coefficient of resistance K = 30,000 psi and a strain hardening exponent of n = 0.20. Determine the stretching force and the stretching force in this operation.
The team performs a cold heading operation to produce the head on a steel nail. The strength coefficient for this steel is K = 550 MPa, and the strain hardening exponent n = 0.24. Coefficient of friction at the die- work interface = 0.10. The wire stock out of which the nail is made is 4.75 mm in diameter. The head is to have a diameter = 9.5 mm and a thickness = 1.5 mm. (a) What length of stock must project out of the die in order to provide sufficient volume of material for this upsetting operation? (b) Compute the maximum force that the punch must apply to form the head in this open-die operation. Discuss the result?
A sheet 300mm wide 25mm thick with two drives, each with a radius of 250mmit is passed through a rolling stand with rollers. Work is thickness in one layer at 50 rpm roll speed 22reduced to mm. The work material has a yield curve determined by K = 275 MPa and n = 0.15.The friction coefficient between the rollers and the work is considered to be 0.12. Successful rolling of frictionDetermine if it is sufficient to allow its operation. If it is sufficient;a) Rolling force,b) Momentc) Calculate the power.
Two high rolling mill setup has been used to reduce the thickness of a plate from 40 mm at the maximum draft per pass to become 34 mm after the last pass. The width of the rolled material is 560 mm and the roll diameter is 560 mm. The material has a strength coefficient of 260 MPa and a strain hardening exponent of 0.18. The coefficient of friction during the process was 0.085. Determine the following: 1- Number of passes required to perform the reduction process = 2- Strain of the last pass = 3- Average flow stress of the last pass = MPa 4- The rolling force to roll the last pass =
A cylindrical part with initial diameter of 45 mm and the initial height of 40 mm is upset forged in an open die to a height = 25 mm. The strength coefficient is 650 MPa and strain- hardening exponent is 0.12. Qa =1.11 (Qa takes into account both friction and workpiece geometry). Calculate the force required for upsetting this part at room temperature. O 1786 kN O 1648 kN O 1247 kN O 1109 kN O none of them
Wire is drawn through a draw die with entrance angle a= 17°. Starting diameter is 3.0 mm and final diameter = 2.4 mm. The coefficient of friction at the work-die interface = 0.08. The metal has a strength coefficient K = 205 MPa and a strain-hardening exponent n = draw force in this operation. Why are multiple passes usually required to achieve the desired reduction? (Hint: Observe the draw stress value found in this question) 0.20. Determine the draw stress and Lubricant box Initial wire stock (in coil form) Multiple pass/draft drawing Draw die V2, F V3, F shown in figure. Capstan drum (holds multiple loops of wire) (1) (2) (3)
(c) A flat rolling operation is being carried out where the roll radius is 200 mm and the roll rotates at 100 rpm. The workpiece material is annealed low carbon steel with 200 mm wide and 10 mm thickness. The strength coefficient and the strain hardening of the carbon steel are 530 MPa and 0.26, respectively. The coefficient of friction is 0.2. (i) Caicurae tne roll force and torque if the workpiece is rolled to a thickness of 4 mm. (ii) Calculate the maximum possible draft and evaluate how friction effect the thickness of the rolled workpiece.
Q1/ A two-high rolling mill is used to reduce plate that is 450 mm wide and 45 mm thick in a single pass to a thickness of 30 mm. The roll has a radius = 500 mm, and its speed = 25 m/min. The work material has a strength coefficient = 300 MPa and a strain hardening exponent = 0.15. Determine: Roll force 8,519,975.11 N 8,619,975.11 N none of the mentioned 8,419,975.11 N
A rectangufar workpiece has the following original dimensions: 2a = 120 mm, h = 40 mm and width = 25 mm (see Fig. 6.5). The metal has a strength coefficient of 530 MPa and a strain hardening exponent of 0.26. It is being forged in-plane strain with u = 0.25. Calculate the force required at a reduction of 25%. Use the average- Question 2 Not yet answered Marked out of 5 pressure formula. P Flag question
I need only part d) plz answer in 30min A 4-in-thick aluminum slab is 10 in wide and 100 in long. It is reduced in one pass in a two-high rolling mill to a thickness = 3.5 in. The roll rotates at a speed = 12 rev/min and has a radius = 20 in. The aluminum has a strength coefficient = 25,000 lb/in2 and a strain hardening exponent = 0.20. Determine the (a) roll force, (b) roll torque, and (c) power required to accomplish this operation, d) Estimate the GHG emission in an hour for the rolling operation.
A hot rolling operation is being carried out on 250 mm wide and 25mm thick low carbon steel (C=165MPA, m=0.10) plate at 1000°C. The roll diameter is 450mm and it is rotating at 120 proposed that a reduction of 20% be taken in the rolling process. rpm. It is If the strain rate in the rolling processes can be expressed by the following expression: V, h. = 3 L h, Where V, is the roll surface speed, ho is the intial thickness of the plate, hfis the final thickness of the plate and L is the contact length between the roll and plate in the deformation zone. Compute the flow stress required to deform the carbon steel plate.
cylindrical roller of radius R1 = 1in. and length L = 1.5 in. is subjected to a load F = 1000 lb as it runs on a parallel roller with radius R2 = 1 in. Both rollers are made of AISI 4340 steel HB 320-340 (E = 30 Mpsi, ν = 0.28). The rollers are in combined rolling with 9% sliding. The coefficient of friction is µ = 0.33. Estimate the lifetime of the rollers.