5. A flanged bolt coupling between two shafts carries 12 bolts in a diameter of 18-in.The shafts carry a torque of 50,000 ft.lb. Assuming that this torque is transmitted byshear across the 12 bolts and that these bolts are to be designed for a shear stressof 3,000 psi, what must be the bolt diameter?18 inFigure 3.6.46. A plate is fastened to a fixed member by four 25 – mm diameter rivets arranged ssshown. Compute the maximum and minimum shearing stresses developed?|20 kN20 kNFigure 3.6.5

Given Data Fastened diameter, D=25mm=0.025m Distance between 20KN to 20KN is 240mm or 0.240 m Now we…

Answered: A plate is fastened to a fixed member…

A plate is fastened to a fixed member by four 25 – mm diameter rivets arranged s shown. Compute the maximum and minimum shearing stresses developed? |20 kN 20 kN Figure 3 65 2000000000:

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Torsion. A flanged bolt coupling connects two shafts. The bolt circle diameter is 250 mm in which there are 12 bolts. The allowable shear stress is 55 MPa in the shafts and 23 MPa in the bolts. One shaft is hollow with outside diameter of 100 mm, while the other one is solid of diameter 50 mm. Determine the ratio of the outside and inside diameter of the hollow shaft and the bolt diameter so that both shafts and the flanged bolt coupling are having the same strength in torsion.
2. A composite shaft is made of slipping a bronze tube of 3-in. outer diameter and 2-in. inner diameter over a solid steel shaft of the same length and 2-in. diameter. The two components are fastened rigidly together at their ends. What is the largest torque that can be carried by the composite shaft if the working shear stresses are 10 ksi for bronze and 14 ksi for the steel? If the hollow tube is made out of steel and the solid shaft is made out of bronze, what is the largest torque that can be carried by the composite shaft if the same working shear stresses are applied? For bronze, G = 6 x 10° psi, and for steel, G = 12 x 10°.
A flanged bolt coupling consists of six 12-mm diameter steel bolts evenly spaced around a bolt circle 300 mm in diameter, and four 25-mm diameter aluminum bolts on a concentric bolt circle 200 mm in diameter. What torque can be applied without exceeding a shearing stress of 60 MPa in the steel and 40 MPa in the aluminum? Use G of ateel = 83 GPa and G for aluminum = 28 GPa
1. Two short shafts having identical diameters of 35 mm and rotating at 1000 rpm are connected by a flange coupling having five bolts with a 100 mm bolt circle. The design shearing stress of the bolt is 12 MPa and design compressive stress of the flange is 15 MPa. a. What is the power in kW transmitted by the short shaft? b. What is the torque transmitted by the shaft in Ib-in? c. What diameter in mm of bolt should be used? d. How thick should the flange be in mm?
A flanged bolt coupling consists of six - in. steel bolts evenly spaced around a bolt circle of 14-in. in diameter, and four- in. steel bolts on a concentric bolt circle of 10-in. in diameter. What torque can be applied without exceeding a shearing stress of 8500 psi in the steel and 6500 psi in the aluminum? Assume Gs = 12 x 10° psi and G, = 4x 106 psi.
A transmission shaft supporting a helical gear B and an overhung bevel gear D is shown in Fig. bearings, A and C. The pitch circle diameter of the helical gear is 450 mm and the diameter of the bevel gear at the forces is 450 mm. Power is transmitted from the helical gear to the bevel gear. The gears are keyed to the shaft. The material of the shaft is steel 45C8 The factors k, and k, of ASME code are 2.0 and 1.5 respectively. Determine the shaft diameter using the ASME code. 400 The shaft is mounted on two 400 400 270 250 210 640i ]640 100
Six 30 mm diameter bolts in the outer bold circle of 370 mm radius are steel A T and six 20 mm diameter bolt in the inner bolt circle of 260 mm diameter are aluminum. What is the torque capacity of the coupling? Assume that the allowable shearing stress for the steel bolts is 40 Mpa and aluminum bolts of 30 Mpa. The Shear modulus of elasticity of aluminum and steel are 28 Gpa and 84 Gpa, respectively. P2 P1 R2 R1 1. 757 T°C Despejado A GGn G8/11/202 O Escribe aquí para buscar acer
A flanged bolt coupling consists of six - in. steel bolts evenly spaced around a bolt circle of 14-in. in diameter, and four- in. steel bolts on a concentric bolt circle of 10-in. in diameter. What torque can be applied without exceeding a shearing stress of 8500 psi in the steel and 6500 psi in the aluminum? Assume Gs = 12 x 10° psi and G, = 4x 106 psi.
Two 35 mm shafts are connected by a flanged coupling. The flanges are fitted with 6 bolts on 125 mm bolt circle. The shafts transmit a torque of 800 N-m at 350 rpm. For the safe stresses mentioned below, Safe shear stress for shaft material = 63 MPa Safe stress for bolt material = 56 MPa Safe stress for cast iron coupling = 10 MPa %3D Safe stress for key material = 46 MPa Calculate: (i) diameter of bolts ; (ii)thickness of flanges ; (iii)key dimensions ; (iv)hub length; and (V)power transmitted.
A flange coupling connects two shafts in order to transmit 250 kW at 100 rpm. It uses 6 bolts with a diameter of 20 mm located at a 210 mm bolt circle diameter. Determine the flange thickness if the bearing stress on the flange is 95 MPa. A. 10 mm B. 20 mm C. 25 mm D. 30 mm
Write legibly, provide manual step by step solution, and diagram for below given problem. A flange bolt coupling has 10 steel coupling 1 inch diameter bolts evenly tighten around a 16.34in. bolt circle. Determine the torque capacity of the connection if the allowable shearing stress in the bolt is 7.3ksi? Ans. 39,034.94 ft-lb
Identify the flange thickness (in mm) of a flange coupling having 6 bolts, that is 10-mm in diameter, with an 80-mm diameter bolt circle, which is used to connect two identical shafts that is 40-mm in diameter. The design shearing stress of the shaft is 20 MPa while the design crushing stress of the flange is 30 MPa.