A pin-jointed truss ABC shown below consists of two links AB and BC. These links are 6 mm thick and 20 mm wide as shown. There are support brackets at A and C. All pins are 12 mm in diameter and a vertical force, P = 5 kN is applied at pin B as shown. The angle 0 =40 deg. and the angle ß = 0 + 20 deg. The normal stress in link AB is (The result is accurate to one decimal place, in the unit MPa. Please write down only the value of your final -$12mm A 20mm -1.0m B

A pin-jointed truss ABC shown below consists of two links AB and BC. These links are 6 mm thick and 20 mm wide as shown. There are support brackets at A and C. All pins are 12 mm in diameter and a vertical force, P = 5 kN is applied at pin B as shown. The angle 0 =40 deg. and the angle ß = 0 + 20 deg. The normal stress in link AB is (The result is accurate to one decimal place, in the unit MPa. Please write down only the value of your final -$12mm A 20mm -1.0m B

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. A bronze bar is fastened between a steel bar and an aluminum bar as shown. Axial loads are applied at the positions indicated. Find the largest value of P that will not exceed an overall deformation of 3.0 mm, or the following stresses: 140 MPa in the steel, 120 MPa in the bronze, and 80 MPa in the aluminum. Assume that the assembly is suitably braced to prevent buckling. Use EsT=200GPA, EAL = 70 GPa, and EBr = 83 GPa. As = 480 mm? Ab=650 mm? Al= 320 mm? 2P 4P 3P 1m 2m 1.5m
Three steel plates, each 16 mm thick and width of 300 mm are joined by two 20 mm rivets as shown. Assume the rivet hole diameter = 23 mm. A. If the load P= 50 KN, determine the tensile stress of the plates. B. If the load P= 50 KN, determine the largest bearing stress acting on the rivets. C. If the ultimate shear stress for the rivets is 180 MPa, what ultimate force Pu is required to cause the rivets to fail in shear? Neglect friction between the plates.
A rigid plate (AC) is connected to flat steel bars by pins at A and B. The horizontal flat steel bar ED is also connected via pins at points E and D. Member AE consists of two 6 mm by 25 mm parallel flat bars, while members EB and ED are single flat bars with dimensions 8 mm by 30 mm. If the structure is subjected to a 2-kip vertical force at point A, find the axial (normal) stress in members AE, EB, and ED. A 2 kip -3'- E B D -3'- C 4'
3. The composite bar consists of a 20-mm diameter steel segment AB and 50-mm diameter brass end segments DA and CB. Find the stress on each segment due to the applied loads. E of steel is 200 GPa and E of brass is 101 GPa. 250mm 250mm 250mm 50mm 20mm 50mm 75KN 100KN brass steel brass D B C 75KN 100KN
Eight steel cables (with equal distance to each other) are supporting a circular heavy moulding of diameter 3m from an overhead point. If the moulding weighs 5 kN/m and the attachment point is 4m above it, determine the following:a. Calculate the tension of the cable.b. Determine the diameter of the wire if the allowable stress is 125 MPa.c. If the diameter of the cable is 10 mm, find the deflection of the steel cable.d. If the diameter of the cable is 10 mm, find the vertical displacement of the molder.
The rigid bar AB of negligible weight is supported by a pin at 0. When the two steel rods are attached to the ends of the bar, there is a gap D= 4 mm between the lower end of the left rod and its pin support at C. Compute the stress in the left rod after its lower end is attached to the support. The cross-sectional areas are 300 mm2 for rod AC and 250 mm2 for rod BD. Use E= 200 GPa for steel. lo/0 0.75 m 1.5m 2 m ANSWER: MPa
The lap joint is connected by three 20-mm-diameter rivets. Assuming that the axial load P=50 kN is distributed equally among the three rivets, find (a) the shear stress in a rivet; (b) the bearing stress between a plate and a rivet; and (c) the maximum average tensile stress in each plate. 130 mm 25 mm 25 mm
The yoke and rod connection assembly shown in the figure below is subjected to a tensile force of 5 kN. 2.1 Determine the tensile stress in each rod. 2.2 Determine the shear stress in pin A between the members. 2.3 If each rod is 600 mm long, determine the overall extension of the assembly. Ignore any stretch in the joint
A simplified model of a basketball hoop is shown. During a basket dunk a player hangs from the rim applying a force of 320 lbs including a dynamic load factor. The stand is a square tube with 5 inches outside length and 0.25 inches thickness. The distance from the edge of the rim to the middle of the square tube is 4 ft. Assuming the model is rigid, the normal stress at point A is most closely equal to: a. 1284 psi b. 1248 psi c. 1212 psi d. 36 psi A
To avoid interference, a link in a machine is designed so that its cross-sectional area is reduced one half at section A-B as shown below. If the thickness of the link is 50 mm, compute the maximum force P that can be applied if the maximum normal stress on section A-B is limited to 80 MPa.
The figure shown is formed by two trusses supporting a block of weight W. The cross-sectional areas of the members are 800 mm2 for AB and 400 mm2 for AC. Find the maximum value of W if the maximum allowable stresses are 110 MPa (megapascals) for AB and 120 MPa for AC. B 40° A W 60° C
A tie rod of ¼ inch diameter is used to hold a plaster wall in place. The tensile stress in the rod caused by load P is 20 ksi. Find the diameter “d” (to the nearest 1/6 inch) of the washer that keeps the bearing stress between the plaster and the washer from exceeding 300 psi.