A multiplexer is a device that selects one among N analog or digital inputs and forwards the selected input to a single output line. Answer the following questions. (Note: You should show all the steps) a) If the mux has 4 inputs, how many control inputs are needed? b) Draw the truth table of 4-to-1 multiplexer.

A multiplexer is a device that selects one among N analog or digital inputs and forwards the selected input to a single output line. Answer the following questions. (Note: You should show all the steps) a) If the mux has 4 inputs, how many control inputs are needed? b) Draw the truth table of 4-to-1 multiplexer.

Electricity for Refrigeration, Heating, and Air Conditioning (MindTap Course List)

10th Edition

ISBN:9781337399128

Author:Russell E. Smith

Publisher:Russell E. Smith

Chapter13: Heating Control Devices

Section: Chapter Questions

Problem 30RQ

See similar textbooks

Similar questions

A multiplexer has 3 select lines and two enables. How many other inputs are there? How many TOTAL inputs are there? How many output/outputs are there? Draw a block diagram of this multiplexer.
4-The element that compares the measured signal with reference input is a. Controller b. Setpoint c. Error Detector d. Sensor
RESEARCH What is an INTEGRATED CIRCUIT (IC)? Uses or applications of Integrated Circuit. Types of Integrated Circuit. Draw at least 4 typrs of IC. Discuss the different IC packages. How to identify the pin numbering of IC? Proper handling of IC. What is seven-segment display? How to produce the required decimal digit from 0 through 9 using seven-segment display? Uses of seven-segment display.
There exists one or more discrete ime signal. What is it control system ? (a) discrete time or (b) continuous time
A multiplexer a. Selects where data should be sent b. Selects one out of several data input lines c. Has a single input and converts it to a binary output d. Has a binary input and converts it to a single output
List four or more functions of signal conditioners.
How many data control lines are required if a multiplexer has eight inputs? a. 8 b. 4 c. 2 d. 3
Please show work included 6. Assume a digital to analog conversion system uses a 7-bit integer to represent an analog temperature over a range of -27oF to 100oF. If the actual temperature being read was 40oF, what would be the closest possible value that the system could represent? Write the answer in a 7-bit binary number as well as in decimal. The answer should be in the following form 00010001 and -10oF a set of two numbers.
Answer the following questions: 1. Design a 8 bit "shift left-shift right" register. 2. Design a 8 bit up counter. 3. Difference between sequential circuit vs combinational circuit. 4. Design a 8:1 multiplexer using 4:1 multiplexer and 2:1 multiplexer. 5. When designing register file, we used multiplexer to read from a specific register of that register file. However, to write in the register file, we didn't use demultiplexer. Why ? 6. In our designed register file, we can write one data at a time. But if we want to write two data at a time,what should we do ? 7.Logisim simulation: A. Design a 8 bit register file with 10 registers. B. Design an ALU with AND, OR, XOR, NOT, ADD and SUBTRUCT operations that can use the above register file. C. Create a single cycle data-path between register file and ALU. Save 1 digit of your NSU ID in each register of your register file before running instructions given below.E.g. for id: 1831565042, save 1 in first register, 8 in second, 3 in third and…
If you can, I need a sample answer with clear details because I want to understand the answer very well. This question from measurements instrumentation course. Thx??
Design the circuit that displays 35861429 on the seven segment display (just one). Use shift registers and button to slide numbers.
Question No.3: Consider a microprocessor based board which has 7-segment and Led is connected to it. Design an assembly language code such that input from user is taken; when user presses “1” “5410” should display on 7-seg Display and when user press 2 leds should glow 5 times in a loop. If any other key is pressed no action should be taken