Assume fc1=600 here A modulation system consisting of input x(t) and output y(t) is shown in Figure 1. Magnitude spectraof mput and impulce rasponce ara giran in Figure 2.Here.a(t)= cas2nf cdte(t) = ces2nfatfc1=500TA-((a/2) KHzfk= (fe) KHzfa-fa/2) KHz(KH:)(a)1) Find the mathematical expressions of yı(t), ya(t), and y(t) in tems of x(t)2) Find the mathematical expressions of Y). Y:), and YO) m terms of X()(3) Sketch the magnitude spectra of |P1()I. |Y2(), and YiIyit)xit)-2fa-JAS(KH:)(b)Figurel. SytemFigure 2. Magnitude spectrum of (a) mput, and (b) impulse respense

Answered: Image /qna-images/answer/6d56ac63-1a83-4e45-a5d6-3ab976239ba6.jpg

A modulation system consisting of input xtt) azd output y(t) is shown in Figure 1. Magnitude spectra of mput and impuisa raspensa ara giren in Figure 2. Here, a(t)= ces2nfat a(e) = ces2nfat fcl=500 [a-fa2) KHz f-(fc/2) KHe = (Sa) KHz F(KH:) (a) ) Fiad the mathematical expressious of ya(), ya), and y() in temus of x(t) Fnd the mathematieal expressions of Y1). Y:). and Y) n terms of X) ) Sietch the magaitude pecta of i(. P:(, and YI H -2f. S(KH3) (b) Figurel. Sytem asodsas esnd (O pa ma (1) 3o maeds apra Tamng

A modulation system consisting of input xtt) azd output y(t) is shown in Figure 1. Magnitude spectra of mput and impuisa raspensa ara giren in Figure 2. Here, a(t)= ces2nfat a(e) = ces2nfat fcl=500 [a-fa2) KHz f-(fc/2) KHe = (Sa) KHz F(KH:) (a) ) Fiad the mathematical expressious of ya(), ya), and y() in temus of x(t) Fnd the mathematieal expressions of Y1). Y:). and Y) n terms of X) ) Sietch the magaitude pecta of i(. P:(, and YI H -2f. S(KH3) (b) Figurel. Sytem asodsas esnd (O pa ma (1) 3o maeds apra Tamng

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

t' 3. Predict the input signal frequencies fi and f2 for the block shown in Figure A3. A₁ sin(2af₁t) A₂ Sin (27f₂t) Figure A3 [M [R Output equation: A/2 [cos (18840t)-cos (43960t)]
Signal and system problem plz explain every step how do this step
Q2- Explain by equations and block diagram the direct method demodulation in NBFM Q3- Write the formula of the phase modulation (PM) when Ac=25 , Fc=10® Hz, Kp= 20 . If an information signal m(t) = cos(212000t) + 10sin(2n2000t) Q4- Drive a formula for NBFM by using Bessel function Q5- If an information signal X(t) = cos(2n700t) + 10cos(25000t). Write the formula of the frequency modulation (FM) when Ac=20 , Fc=10® Hz, Kf= n2000 Q6-) If NBFM signal passes through a frequency multiplier. With B < 0.5 and fc=200kHz. Let fm ranges from 50OHZ to 15kHz, and let the maximum frequency deviation Afat the output be 75kHz. Find the required frequency multiplication n and the maximum allowed frequency deviation at the input. Q7- If an angle modulated signal S(t) = 10[cos(210®t) + 15sin(2n10³t)]
Q17. The circuit shown in figure Bl17 is used to amplify wide band of frequency from 20KHZ to 150MHZ. Assume Vcc=20V, VCE= 4.5V, Is=70µA, Ik-8.5mA and Zin=2702. Design the value of Resistors. i) R1. ii) Rc and RE. Output Input Signal Figure B17 ww ww- ww
At two distinct places, a signal is measured. At the first point, the power is P1, and at the second point, it is P2. The decibel level is zero. This denotes
3-16 An audio oscillator operating at 1 kHz is gated on for an interval of 5 ms by a single baseband pulse. Sketch the form of the amplitude spectrum in the vicinity of the major positive frequency lobe, and label significant frequencies.
select one quickly Mod-N counters can be used for frequency ........... . a) dividing, b) subtracting , c) adding , d) multiplying.
please answer question 1.b quickly… please answer base on my matric number not as same like question.. my matric no is 201061325 so the last 3 digit is 325 so the selected low cut-off frequency is equal to the 32 khz while the high cut-off frequency is 5khz … so use the value that i give... thank you
Transmitter: a carrier frequency of 108 kHz and a modulating frequency of 0.3 kHz to 3.4 kHz is applied to an amplitude modulator. The USB and the LSB are both transmitted to the distant receiver, with a suppressed carrier. Receiver: the resultant USB and LSB from the transmitter are input to an amplitude demodulator. A carrier frequency of 108 kHz is reintroduced to the demodulator. Determine the following: 1. The LSB and USB at the output of the modulator. 2. The LSB and USB at the output of the demodulator.
A carrier signal of 12 V amplitude is modulated by an Bhutananahuhu information signal to a depth of 90%. Calculate the Vmax and Vmin for the modulated wave. tututututu
For the given circuit below, the RF generator is set to EXT MOD, 500kHz. RF GEN 500KHZ R1 2702 R2 10K ELECTRONIC VOM 0.0047pF a) What is this circuit? b) Is there an RF signal across R2? c) Draw the expected signal waveform across R1 d) Draw the expected signal waveform across R2 e) What is the expected frequency of the signal across R2?
a) Write the equation of the modulated wave. b) Sketch the waveform of modulated wave and write its equation if the modulation type is AM/DSB- SC. 62 -8 -14