A manufacturer synthesis a high frequency laminated substrate with characteristics as Table below at 10 MHz. Substrate S1 10μο 4ɛ. 3S/m S2 Ho 5.8 x 107S/m S3 Ho 6.1 x 107S/m S4 Ho 24ɛ. 4S/m 55 Ho 81ɛ, 25S/m (a) Which of these materials can be treated as the best conducting at 10MHZ and justify your reason with two characteristics of the material. (b) Based on your answer in (a), kindly assist the manufacturer to determine other characteristics which are phase constant, velocity, wavelength, skin depth and intrinsic impedance.

A manufacturer synthesis a high frequency laminated substrate with characteristics as Table below at 10 MHz. Substrate S1 10μο 4ɛ. 3S/m S2 Ho 5.8 x 107S/m S3 Ho 6.1 x 107S/m S4 Ho 24ɛ. 4S/m 55 Ho 81ɛ, 25S/m (a) Which of these materials can be treated as the best conducting at 10MHZ and justify your reason with two characteristics of the material. (b) Based on your answer in (a), kindly assist the manufacturer to determine other characteristics which are phase constant, velocity, wavelength, skin depth and intrinsic impedance.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

Consider more realistic situation, silicons intrinsic Fermi level isn't at the midgap. Please find the energy differences between real Fermi level and midgap Please give some explanations.
RI Rz Vo %3D 2R.R.CG. REZ 1.+ Redrawthe circuit-equivalentwhenoperatingat-a-DC-voltage(0Hz).1 VerifyusingKCL-that-the circuit-operation will-be-that-of a-non-invertingamplifier. 2.→ Redrawthe circuit-equivalentat-veryhigh-frequencies.-VerifythatVoutisshorted.-(Hint.-Note- thereactance at-thenon-invertinginputat-extremelyhighfrequencies.--What-will-bethe- voltage at-that-node?-What-doesthis-meanfor-the voltage at-Rf2?)1 3.+ Let-C1=C2..-Calculate thevaluesofC1-and-C2-for-a-cut-offfrequency of500-Hz-if-R1-and-R2. are-33kohm-and-choosereasonablevaluesof Rf1 and-RF2•50-thatthe-gain-at-low-frequenciesis- 4-dB.--1 4.→ Simulate the circuit-on-Multisim-andrepeatsteps4-and5-of-Part-1-again.--Produce its-Bode Plot- using-the AC-Sweepfunction.-Identify-the type of responsecurve andtheroll-offrate. +,
(D) Fermi-level in terms of "Intrinsic fermi-level". For n-type, E-E=kT InD Free Cra N For p-type, E-E, = kT In 4 n,
(b) Compare and construct the band energy diagram of conductor, insulator and semiconductor materials. Explain each of the band energy level in a table form.
Hole mobility...
a carrier frequency 10⁶ and amplitude 3V frequency modulated by a sinusoidal wave of frequency is 500 HZ and the peak amplitude 1 Volt as a consequence , the frequency deviation is 1 KHz. The level of the modulating waveform is changed to 5 Volt peak and the modulating frequency is changed to 2KHz. Write an expression for the new modulated waveform.
4. By using the OCC describe the relationship between the excitation current and the generated voltage.
(P-06) Diode FullWave (Course: Electronic Devices and Circuit Theory). -Use Equation Operators or write it down on paper/digital paper. -Redraw and Apply. -Please answer without abbreviation. Thank you.
. Draw and explain the structural overview of MOSFET Capacitances.
Problem 2 In a P-type semiconductor. the Fermi level is 0.3 cV above the valance band at a room temperature of 30O °K. Determine the new position of the Fermi level for termperatures of (a) 350 K and (b) 400 K. The Fermi level in a P-type material is given by
Describe the electrochemical double layer capacitor (EDLC) using carbon electrode.
Tha voltage va can be expressed as? And the supernode equation can be expressed as?