A load P is supported by two concentric steel springs. Given: Inner Spring: 30 turns of 20-mm ø wire Mean ø = 150 mm Outer Spring: 20 turns of 30-mm ø wire Mean ø = 200 mm Find the maximum load that will not exceed a shearing stress of 140 MPa in either spring. G = 83 GPa.

A load P is supported by two concentric steel springs. Given: Inner Spring: 30 turns of 20-mm ø wire Mean ø = 150 mm Outer Spring: 20 turns of 30-mm ø wire Mean ø = 200 mm Find the maximum load that will not exceed a shearing stress of 140 MPa in either spring. G = 83 GPa.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.4.12P: Solve the preceding problem if the mass of the tailgate is MT— 11 kg and that of the crate is hic—...

See similar textbooks

Related questions

Q: 4. A 200 lb force P is exerted on the lever. What will be the deformation, in inches, in the 0.0630…

Q: A solid, circular bar ABC consists of two segments, as shown in the figure. One segment has a…

A: When a shaft is subjected to torque, shear stress produces in the shaft. The torsion equation is…

Q: A circular steel tube of length L = 1.0 m is loaded by torques T a) If the inner radius of the tube…

A: a. At inner surface: from the given data, Shear strain,

Q: PROBLEM 1 Diameter of pin at A = 25 mm Diamcter of cable BC = 10 mm Ultimate shear stress of pin =…

A: Given: dA=25 mmdBC=10 mmτmax=120 MPaσcable=1250 MPa

Q: (7) The figure shows the free body diagram of a connecting link portion having stress concentration…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of…

Q: Q4 The L2 steel bolt as shown in Figure Q4 has a diameter of 5 mm, and the link AB which is made…

Q: QF8: The 0.06R (mm)-diameter bar is made of a brittle material with the ultimate strengths of 0.1SR…

A: Given: The diameter of bar, d = 0.06R The ultimate strength of bar = 0.15R MPa (T) and 0.25R (C)

Q: Useful equations; o = E A 1. The steel shaft carries the axial loads as shown in the figure below.…

A: Given axial load action on stepped shaft as shown below

Q: 15 kN 2) Two objects are glued on the angled plane as shown in figure. If the ultimate stress for…

Q: s): The butt connection shown below is fastened by 20-mm diameter bolts. Find the maximum allowable…

A: given; diameter (d)=20mmload(P)=?bearing stress(σb)=160MPatensile stess(σt)=80MPashearing…

Q: The figure shows truss. It is supported with a pin at A and a roller at B. There are three pointed…

A: (a) Draw the free-body diagram of the truss.

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6…

Q: n the mechanism shown below, the distributed load W is 300 N/m and the angle 0 is 55 knowing that…

Q: Two plates with a thickness of 35 mm, width of 160 mm, and length of 200 mm are joined together by a…

A: Given data: - Thickness of the plate, t=35 mm,Width of the plate, w=160 mm,Length of the plate,…

Q: LA load F of 500 N is applied in the negative x-direction on rod OA, and a load P of 200 N is…

A: Given: The load, F = 500 N The force at B, P = 200 N

Q: Consider the compound shaft KC which is compose of a 1200mm long solid rod fitted snuggly into an…

Q: 2. A prismatic bar under an axial load produces a tensile stress of 75MPa on a plane at an angle of…

A: Calculated normal and shearing stress in all faces of the element at an angle of 50 degrees.

Q: 5.) A pin made of steel is inserted in a short hanging wooden member and is used to support load F =…

A: Given dataSupport load F = 20kNUltimate strength of the wood is 60Mpa in tension and 75MPa in…

Q: A straight and piecewise uniform bar ABCD of total length L is in Case 1 fixed at A in case 1 and in…

A: considering case 1applying static equlibirium conditions∑Fx=0−R+10=0R=10 KNconsidering section…

Q: A F F W2 d A Section A-A The following figure shows the free-body diagram of a connecting-link…

A: FROM DATA BOOK, Sut=64kpsi Sy=54kpsi a=2.7 b=-0.265 kb=1 kc=0.85 endurance limit, Se=0.5Sut…

Q: The rigid bar AB as shown in Figure Q1(a) is supported by a steel road AC having a diameter of 22 mm…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 6…

Q: A pulley is keyed to a shaft midway between two anti-fiction bearings. The bending moment at the…

Q: A steel bar with diameter d1 = 10 mm has upset ends with diameter d2 = 15 mm. The lengths of the bar…

A: Given that, d1=10 mm,d2=15 mm,L1=0.3 m,L2=0.15 m,R=1.25 mm,E=90 GPa,δ=0.5 mm,

Q: at some point sha has à diameter a isider the croSs section of a solid and its material has a yield…

A: Given, Tension = T Vertical shear force = V

Q: B. 5 m 3 m 30 mm -20 mm T20 mm The assembly above includes pin-connected column AB. Suppose that an…

Q: A solid, circular bar ABC consists of two segments, as shown in the figure. One segment has a…

A: Given,

Q: 4. Given a shear stress of T35 MPa and a shear modulus of G-75 GPa, the shear strain is most nearly…

A: Given data : Shear modulus is denoted by G Shear stress is denoted by ζXY Required : Shear strain

Q: A helical spring used in an automobile suspension is having a wire diameter of 6mm and an outside…

Q: 3. A load P is supported by two concentric steel springs. Given: Inner Spring: 30 turns of 20-mm ø…

A: Given: A load P is supported by two springs. The number of turns of inner spring is, n1=30. The…

Q: 2. A close -coiled helical spring having 12 coils must absorb 200 joules of energy and support a…

A: Given data⇒n=12 coilsE=200 joulesF=10 kNζ=220 MPaG=80 GPaProblem definition⇒Problem says determine…

Q: A normal-weight concrete masonry unit is 40cm by 20cm by 15cm thk. A wall made up of this material,…

A: Given Data The height of the wall is: H=3 m The length of the wall is: L=5 m The density of the…

Q: (B) // The straight beam with distribution load as shown in figure B is simply supported by a pin at…

Q: A short steel tube of external diameter 70 mm and internal diameter 40 mm is surrounded by a brass…

A: Given:do=70 mmdi=40 mmDo=80 mmDi=90 mmP=20 KNL=30 cmEs=2.1*105 N/mm2Eb=1.1*105N/mm2

Q: P1.30 Rigid bar ABC shown in Figure Pl.30 is supported by a pin at bracket A and by tie rod (1). Tie…

A: From trigonometry -

Q: 15 Q6) An aluminum bar having a cross-sectional area of (50.265 cm2) carries the axial loads applied…

A: Given, Cross sectional area = A = 50.265 cm2 = 50.265 x 10-4 m2 Yound modulus = E = 10 x 106 N/m2…

Q: Rigid bar ABC is supported by a pin at bracket A and by tie rod (1). Tie rod (1) has a diameter of 8…

Q: A steel bolt of 6 mm in diameter has a tensile load of 40 kN. Find the average tensile stress at the…

A: Step by step solution is given below

Q: (15) The figure shows the free-body diagram of a connecting-link portion having stress concentration…

Q: B A homogenous bar AC with negligible mass is supported by a pin at A and cable BC, carried a load…

A: A pin support will experience both horizontal and vertical components of reactions at A. The tension…

Q: A bar ABC fixed at both ends A and C is loaded by an axial load (P) at C. If the distances AB and BC…

Q: t (0) is 0.15°/

A: given:γmax=500×10-6 rad

Q: A slip collar with weight W =150 pounds fallsfrom a heighth = 2inch. Towards a flange located at the…

Q: Q.5) A bar of 1000 mm length and 40 mm diameter is centrally bored for 300 mm length at one end at a…

A: Given Data P=30 kN

Q: A steel pipe is part of a drilling rig to build foundation piles The outer d 2 is equal to 6 in and…

A: To obtain the magnitude of the shear force on the various fibers of the beam, we must use the pure…

Q: L1 PB 2 E2 L2 D2 Dimensions: L2 L1 D2 D1 17 mm 18 cm 23 cm 15 mm Problem Statement: The rod shown is…

A: Consider the following diagram showing the forces (loads) acting on the system of two rods of…

Q: Compare the torsional rigidities of the following sections: (a) a hollow tube 30 mm outside…

A: Since we only answer up to 3 sub-parts, we’ll answer the first 3. Please resubmit the question and…

Q: 10 cm 600 N 14 cm B -- Vertical load is applied to point Bof a 10 mm radius cylindrical bar as shown…

A: Given data: Radius of the cylindrical bar is: r=10 mm which is fixed at point 'C'. We need to find…

Question

100%

A load P is supported by two concentric steel springs.
Given:
Inner Spring:
30 turns of 20-mm ø wire
Mean ø = 150 mm
Outer Spring:
20 turns of 30-mm ø wire
Mean ø = 200 mm
Find the maximum load that will not exceed a shearing stress of 140 MPa in either
spring. G = 83 GPa.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Step by step

Solved in 5 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Repeat Problem 11.2-3 assuming that R= 10 kN · m/rad and L = 2 m.
Solve the preceding problem if the mass of the tailgate is MT— 11 kg and that of the crate is hic— 6S kg. Use dimensions H = 305 mm, L = 406 mm, dc= 460 mm, and dT= 350 mm. The cable cross-sectional area is At= 11.0 mm'. (a) Find the tensile Force T and normal stress T in each cable. (b) IF each cable elongates
Solve the preceding problem for W = 1.0 lb. h = 12 in.,and k =0.511,/in.
Three round, copper alloy bars having the same length L but different shapes are shown, in the figure. The first bar has a diameter d over its entire length, the second has a diameter d over one-fifth of its length, and the third has a diameter d over one-fifteenth of its length. Elsewhere, the second and third bars have a diameter Id. All three bars are subjected to the same axial load P. Use the following numerical data: P = 1400 kN, L = 5m,d= 80 mm, E= 110 GPa. and v = 0.33. (a) Find the change in length of each bar. (b) Find the change in volume of each bar.
ASAP
Member AB (helical spring) and Member AC (axial rod) are carrying a weight at point A. Member AB has the following properties: R = 90 mm, n =4 turns, G = 70 GPa, d = 30 mm, and Tallow = 105 MPa while Member AC has the following properties: L= 2, A= 500 mm2, E 200 GPa, and oallow = 30 MPa. Determine the maximum safe value of W (in N). Use simplified formula for the helical spring.
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 11 mm and an allowable normal stress of 165 MPa. Pipe (2) has an outside diameter of 48 mm, a wall thickness of 7 mm, and an allowable normal stress of 75 MPa. Assume x₁ = 2.9 m, x₂ = 1.5 m, and y₁ = 3.9 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. Answer: Pmax (1) B KN
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 13 mm and an allowable normal stress of 135 MPa. Pipe (2) has an outside diameter of 56 mm, a wall thickness of 6 mm, and an allowable normal stress of 150 MPa. Assume x₁ = 3.7 m, x₂ = 1.5 m, and y₁ = 3.0 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. B P 3₁ (1) Answer: Pmax X1 i C kN
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 11 mm and an allowable normal stress of 75 MPa. Pipe (2) has an outside diameter of 48 mm, a wall thickness of 8 mm, and an allowable normal stress of 120 MPa. Assume x₁ = 3.1 m, x2 = 2.0 m, and y₁ = 4.4 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. 3/₁ x₁ Answer: Pmax i B 3 P C kN
1. A safety valve spring having 9 and 2 coils has the ends squared and ground. The outside diameter of the coil is 115 mm and the wire is 13 mm. It has a free length of 203 mm. The length of which this spring must be initially compressed to hold a boiler pressure of 1.38 MPa on the seat of 32 mm diameter. Modulus of rigidity is taken as G=80GN/m?. a. Find the force acting on the valve set. b. Determine the mean diameter c. Determine the spring index d. Find the spring deflection e. Find the operating length f. Calculate the solid length g. Calculate the deflection of solid length h. Compute the solid force i. Compute the Wahl factor
Two coaxial closed coil springs make up a standard compound helical spring. When both springs are unloaded, they are not of equal length. If each spring's working stress is to be the same. The wire material has an 80 GPa modulus of rigidity. Find the diameter of steel wire for inner spring and stiffness of inner spring. Also find the stiffness of the compound spring. Outer spring a: Mean coil diameter = 100 mm No. of turns = 15 Wire diameter = 12.5 mm Inner spring b: mean coil diameter = 75 mm No. of turns = 20
Pipe (2) is supported by a pin at bracket C and by tie rod (1). The structure supports a load P at pin B. Tie rod (1) has a diameter of 13 mm and an allowable normal stress of 125 MPa. Pipe (2) has an outside diameter of 56 mm, a wall thickness of 8 mm, and an allowable normal stress of 100 MPa. Assume x₁ = 2.8 m, x2 = 1.6 m, and y₁ = 3.7 m. Determine the maximum load Pmax that can be supported by the structure without exceeding either allowable normal stress. B P Y₁ (1) Answer: Pmax =