A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 13500 ksi] rods, and a solid steel [E = 30100 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.73 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.54 in. Assume L1=53 in and L2-73 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 23 kips is applied. (2) L2 (1) L1 B. C. Answers: ksi.. ! ksi,

A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 13500 ksi] rods, and a solid steel [E = 30100 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.73 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.54 in. Assume L1=53 in and L2-73 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 23 kips is applied. (2) L2 (1) L1 B. C. Answers: ksi.. ! ksi,

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

SITUATION 1 Determine (approximately) the force in each member of the truss. Assume the diagonals can support either a tensile or a compressíve force and assuming that the díagonals cannot support a compressíve force. A. Use Method 2 7 k 14 k 14 k 7 k Н F E oo 2 k 380 6 ft A D В C 8 ft 8 ft 8 ft B. Use Method 1 50 kN 40 kN 20 kN E D 3 m B 3 m 3 m
D 2a В 4а 2a 4a E 390 The columns AC and DE are connected to the bars BD and CD by pins. The support at A is a pin and the support at E is a roller. Determine the forces acting on each column due to the horizontal linearly distributed load on AC and vertical unifrom load on CD. Present your solution as two FBDS showing the actual forces.
The bar of the pin connected frame shown are each 30mm by 60mm in section. determine the maximum load P that can be applied so that the stress will not exceed 100MN/me in tension or 80 MN/me in compression
The bridge truss shown carries the following uniform live load and concentrated live load. A B C D E 3m K FA G H se8m W(LL) P(LL) 15 110 Calculate the following: 9. Maximum force on member BC
!! Show Comlete & Detailed Solution w/ FBD !!The rigid bars AB and CD are supported by pins at A and D. The vertical rods are made of aluminum and bronze. When the force P = 18 kips is applied, and neglecting the weights of the members, determine the:a. axial force of the aluminum bar;b. axial force of the bronze bar;c. deformation of the aluminum bar;d. deformation of the bronze bar;e. vertical displacement of the point where Pis located.
Each bar of the truss has a rectangular cross section, 30 mm by 60 mm. Determine the maximum vertical load P that can be applied at B if the working stresses are 100 MPa in tension and 80 MPa in compression. (A reduced stress in compression is specified to reduce the danger of buckling.) B 8m Gm 10m
FIGORE %3D aluminum [E = 70 GPa] links (1) and H.W.3: In Figure (2) support rigid beam ABC. Link (1) has a cross-sectional area of 300mm2, and link (2) has a cross-sectional area of 450 mm2. For an applied load of P = 55 kN, determine the rigid beam deflection tad Nadhon hub at point B. (2) 4,000 mm (1) 2,500 mm 1,400 mm 800 mm P. FIGURE
Determine the force in each member of the loaded truss. The forces are positive if in tension, negative if in compression. Assume F-2770 N, a-2.1m, b-4.2 m, 0 = 48% Answers: AB- AC- AD- BC- B CD i i i b 8 N N N N N
Two aluminum (Ea=77 GPa) rods AB and CD, and a steel (Es=202 GPa) rod EF support a 82.7 kN load P. Each of the rods has a 400 mm2 cross- sectional area. Neglecting the deformation of rod BED, determine the change in length (in mm correctly up to two decimal places) of rod AB. A C P 500 mm В E 400 mm F
Q1// The compound wooden beam is connected together by a bolt at B. Assuming that the connections at A, B, C, and D exert only vertical forces on the beam, determine the required diameter of the bolt at B and the required outer diameter of its washers if the allowable tensile stress for the bolt is 150MPa and the allowable bearing stress for the wood is 28MPa. Assume that the hole in the washers has the same diameter as the bolt. -2 m- 3 kN 2 kN 1.5 kN 2 m--1.5 m-1-1.5 m-1-1.5 m--1.5 m- B D
Aload Pissupported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 17400 ksi] rods, and a solid steel [E = 30600 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.79 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.52 in. Assume L1=39 in and L2=77 in. If all bars are unstressed before the load Pis applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 29 kips is applied. |(2) (1) L2 (1) B. Answers: i ksi. ksi.
The compound bar carries axial loads as shown. Determine the maximum allowable value of P if the change in length of the entire bar is limited to 0.08 inch and the working stresses listed in the table are not to be exceeded. Steel 2 ft Bronze 4 ft Aluminum 3 ft 2P 3P 4P A (in.?) E (psi) a. (psi) Steel 0.75 30 x 10 20000 12 x 10 10 x 10 Bronze 1.00 18000 Aluminum 0.50 12000