A hydraulic turbine at sea level is placed 5 ft above the water level at the tailrace. Water temperature is 60°F and the critical cavitation parameter is 0.1. What is the maximum head in feet that you can operate the turbine without cavitation? Select one: O a. 283 O b. 382 O c. 328 O d. 238

A hydraulic turbine at sea level is placed 5 ft above the water level at the tailrace. Water temperature is 60°F and the critical cavitation parameter is 0.1. What is the maximum head in feet that you can operate the turbine without cavitation? Select one: O a. 283 O b. 382 O c. 328 O d. 238

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Oil at 38 deg. Celsius is being drawn from a closed tank having a pressure of 70 kPa gage. The level of oil in the tank is 2.5m above the pump centerline. The suction line friction loss is 0.6m. The vapor pressure of the gasoline is 48 kPa absolute and its specific gravity is 0.82 Determine the NPSH in meters available. choices: a. 19.36 b. 17.23 c. 4.64
1 QUESTION 1 Consider a desired pump operating condition which adds 35 psi at a flowrate of 500 gpm to water (p= 62 11m/ft²³) Ignore any changes in Kinetic or potential energy and Tassume isothermal flow C.e. internal energy is constant, this is the normal assumption we make when analyzing fluid flows in piping systems). Apply the energy balance only across the pump with full energy Balance and simlifying to solve for the pump, Starting head symbolically. Then begin careful of units, Solve for pump head in feet. GIVEN: 35psi 500 gpm p=62 1bm/3 XA. 10.5 A B. 100.8 ft C. 50.1 ft D. 80.7f 35 500 62 (32.2) + 2(32.2) 35 + 500
During a test run of a Pelton wheel turbine, the pressure at the nozzle was 2.25 MPa when water flowing in the penstock at 1.7 cubic meter/sec. The penstock diameter is 600 mm. Determine: a. The effective head in meters 255.09 231.27 241.36 b. The Water Power (WP) in kW 3,855 4,226 3,413 c. The turbine power in kW if the turbine efficiency is 80% 3,277 3,413 3,084 d. the generator output in MW if the generator efficiency is 92% 2.837 3.139 2,837
Water is pumped through a vertical 5.0 cm cement-lined steel pipe to an elevated tank on the roof of a building. The measured pressure at the discahrge side of the pump is 1380 kPa. What pressure can be expected at a point in the pipe 76 m above the pump when the flow is 9.5 L/s? Use f= 0.023 a. 100 kPa b. 225 kPa c. 150 kPa d. 75 kPA
Apply the formulas in designing a hydraulic turbine to select the appropriate type of turbine for the following design considerations:a. Gross head = 200mb. Flow rate = 10m3/s c. Penstock friction losses = 10% of gross headd. Overall Efficiency = 95%e. Coefficient of velocity, Cv = 0.95f. Peripheral coefficient, Φ = 0.46g. Rotational speed = 3200 rpmCompute Ns and net head to validate the answer. Calculate also the diameter of the turbine wheel.
Water is pumped through a vertical 5.0 cm cement-lined steel pipe to an elevated tank on the roof of a building. The measured pressure at the discahrge side of the pump is 1380 kPa. What pressure can be expected at a point in the pipe 76 m above the pump when the flow is 9.5 L/s? Use f= 0.023 a.225 kPa b.100 kPa c.75 kPA d.150 kPa PLEASE INCLUDE FIGURE OR FBD
From a very large tank with an absolute pressure of 3 bar, the water is discharged to the atmosphere by means of 2 smooth pipes of 100 m length, 1 m and 50 m long, connected in series. The height difference between the water level in the tank and the outlet is 50m, and the diameters of the pipes are 50mm and 100mm, respectively. In addition, a 500kPa turbine is placed on the 2nd Pipe. a) Draw the system roughly, show the dimensions on it.b) Calculate the exit velocity of the water from the 2nd pipe, ignoring the local losses.
Figure below shows a siphon that is used to draw water from a tank. The siphon tube has an inside area of . The exit nozzle at point F has an inside area of . The distances are , , and , respectively. Find the pressure at point D_______ A. 5.74 kPa (gage) B. -5.74 kPa (gage) C. 5.74 kPa (absolute) D. -5.74 kPa (absolute)
Water is pumped through a vertical 5.0 cm cement-lined steel pipe to an elevated tank on the roof of a building. The measured pressure at the discahrge side of the pump is 1380 kPa. What pressure can be expected at a point in the pipe 76 m above the pump when the flow is 9.5 L/s? Use f= 0.023 a.75 kPA b.225 kPa c.150 kPa d.100 kPa With F.B.D
1st: Using the formula t = determine the Caa/29 coefficient of discharge. “A" of tank Note: 1. "A" depends on the size of your bottle, 2. "a" depends on the size of the hole you punched 3. Let the initial head of water equal to 10 cm 4. You can determine "t" through experiment 5. Hence, the only unknown is the value of Cd. 6. Repeat the process, try using head of water equal to 15 cm, then 20 cm. “a" of orifice 7. Hence, you have 3 values of Cd. 8. Tabulate and graph the results. Be creative. Referred: 1.5 L water bottle or alike You need to provide pictures for No.1 to No.3. Show your solution in No.5. (x3 due to trial 1, 2, and 3. 2nd: Utilizing the same bottle, determine the average velocity of the fluid flowing through the water using the formula Q = CqA¿V¢ - "A" of tank Note: • Let Q = Volume / time. Use a beaker or measuring cup to determine the volume, then record the time “a" of orifice until water "runs" out. Be careful, volume refers only to the amount of water above the…
1. Assume a horizontal shaft handling water at 65 deg C (Pv=2.503 KPa, Density=980.5 m3/kg). The suction nozzle is 4.35 m below the pump centerline and the pressure gauge reading at this point is 221Kpag. Determine the NPSHa if the head loss is 0.82 m. If the NPSHr is 3m less than the NPSHa you got on question number 1, determine the pump suction specific speed at pump rotating at 1800rpm and Q=500gpm
Pls. answer thank you! A pelton type turbine was installed 31m below the head gate of the penstock. The head loss due to friction is 15% of the given elevation. The length of the penstock is 80 m and the coefficient of friction is 0.00093 (Morse). Determine the diameter in meters of the penstock and the power output in KW.