A horizontal pipe with a constantdiameter of 0.04 mhasa skady flaw of Refnigerant 134a entering at 300 kla40°C, and a mass flow rate of 0.6 kg/sec, and leaving at l240 kla and 50°C Deteminethe magnitude of the rateOf heat transfer between the pipe and its Surroundungs inkW using 5 signifigant figures. quoLg SMt gunb ot pn

Answered: Image /qna-images/answer/ae7db107-b13f-43c0-a7d3-b5f188e46e6b.jpg

A horizontal pipe with a constantdiameter of 0.04 m has a skady flow of Refrigerant. 134a entering atm300 kla 40°C, and a mass flow rate of 0.6 kg/sec, and leavung at l 240 kla and 50°C Deteminethe magnitude of the rate Of heat transfer between the pipe and its surroundungs in kW Using 5 Sighifigant fiqures. g sAt sünb of ie0

A horizontal pipe with a constantdiameter of 0.04 m has a skady flow of Refrigerant. 134a entering atm300 kla 40°C, and a mass flow rate of 0.6 kg/sec, and leavung at l 240 kla and 50°C Deteminethe magnitude of the rate Of heat transfer between the pipe and its surroundungs in kW Using 5 Sighifigant fiqures. g sAt sünb of ie0

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

b Soram generators are a type of heat exchanges that are used i power plants to gemerate steam at desired pressure and temperature e as bộ, na steam generator, saturated liquid water at 30Centers a 6omm diameter tube at the volume flow ate of 12US. Ater exchanging heat with hot gn the water changes to steam and leaves the generator at a pressure ofs MPa and a temperature of 400C. During this procesa, the dameter of the water/veam tube does not change. 2 shemnc of the tam eron w Cakculate the steam ma flow rate. a what is the iniet veiocity of the eam (4 marks 2marks what is the esit velocty of the steam Omarka M Calculate the rate of heat transfer in Mw) required to change the phase of lquid water to steam. 6 marka
Water is entering a heated tube at mass ow rate of 1.2 kg/s. The temperature at the inlet is 20 C and at the outlet is 80 C. Assume the surface temperature of the tube is 100 C. The convection coe cient of the water ow is 28 W=m2 C. The speci c heat and density of water can be assumed to be 4180 J=kg C and 990 kg=m3. What is the rate of heat transfer to water during this proces
Heat Transfer Questiion is image
A copper rod whose diameter is 2 cm and length 50 cm have one end in boiling water, the other end in a jacket cooled by flowing water which enters at 10oC. The thermal conductivity of the copper is 0.102 kCal/m-soC. If 0.20 kg of water flows through the jacket is 6 min, by how much does the temperature of the water increase?
Compartnments A and B of the tern k Shown in the figure below are closed and filled with air end a liquid with el specific grauity equal to o.6. 3.5hpa(gauge) B Open to the et moshore 3.ocm air Liquid with e specific grauity =0.6 water mercary w th a specific grauity =13.6 O If the atumospheric press ure is lol kpa Cabr) and preffure gaugle reads 3.5trpa (gauge).determine the manometer reading, h.
Anser question for (a) only for Heat Transfer
2.0 Air is cumpressed in a diesel engine from an initial pressire of 13 psia und a temperature of 120 "Fts one - twelfh of its origmal volume. Caleulate the tinal semperature assuming the compression to be adiabatic. Answer 1107 °F
Compartments A andB of the tenk Shown in the figure below are closed and filled with air end a liquid with el specific grauity equal to o.6. 3-5rpa Cgauge) Open to the et moshere 3.ocm air Liquid with e specific gracity =0-6 water mercary wth a seecific greuity S(3•6 O f the atmospheric pressure is lol kpu Cabr) and prefure gaugle reads 3.5trpu (gauge).determine the manometer reading, h.
Examplet A steel d of deameter 2:5cm is endoea eentsally in a kollioweo copper fube of externel diameter a kollio coP per tube of diameter of 3em bay i's Subjected to au aeial pull of H5UON. scm and infernd - he compente full of 500N. arial Scm It Hhe length of he tube is 20cm, determine 2.5 ☺stresses in fte ric aud #e tube eauh bar le load Coy each 6ar. Carsied diameter of rod=2'scm Siaint= 3cm
HEAT TRANSFER,PLEASE GIVE COMPLETE WORKING Hot air at 80ºC enters an 8-m-long pipe at a rate of 0.15 kg/s. The pipe is considered as thin wall with diameter of 20 cm. The wall of the pipe is observed to be nearly at isothermal at 60ºC. The fluid properties of the hot air is as given on Table 1. Determine: The temperature of the air at the exit of the pipe. The heat loss from the hot air. Table 1: Thermo-physical properties for hot air k = 0.02953 W/m·K µ = 20.96×10-6 N·s/m2 Pr = 0.7154 cp = 1008 J/kg·K
(heat transfer ) thanks The velocity of the fluid flowing in parallel over a 500mmx500mm flat heater surface is U= 19 m/s and the inlet velocity temperature is T_∞15 C. The surface temperature of this plate is T_s140 C, the friction force is F_D=0.4 N and the surface area of the plate is A=0.32 m2. According to this;(F_D= 0.4N A=32 m2)a) Surface shear stressb) Find the coefficient of frictionc) Heat transfer coefficientd) What is the amount of heat transfer (electric power) that must be given to maintain a constant surface temperature?
Q4/ А wall (Зт*2m) соnsist of 10 ст face brick with 15 ст сопсrete plaster. The outdoor temperature is -7°C, while the indoor space temperature is 24°C DBT and 10°C dew point temperature, Find i)heat transfer(Q) through the wall ii) Will moisture condense on this wall? and I.3 ст сетеnt