A homogeneous 800 kg bar AB is supported at either end by a cable as shown in Fig. P-105. Calculate the smallest area of each cable if the stress is not to exceed 90 MPa in bronze and 120 MPa in steel. Figure P-105 Bronze L= 4m Steel L= 3m 10 m

A homogeneous 800 kg bar AB is supported at either end by a cable as shown in Fig. P-105. Calculate the smallest area of each cable if the stress is not to exceed 90 MPa in bronze and 120 MPa in steel. Figure P-105 Bronze L= 4m Steel L= 3m 10 m

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter8: Applications Of Plane Stress (pressure Vessels, Beams, And Combined Loadings)

Section: Chapter Questions

Problem 8.2.1P: A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the...

See similar textbooks

Related questions

Q: Q3: The rigid bar ABC in the Figure is pinned at B. Initially, the bar is horizontal. If the…

A: Area of cable Ac=200 mm2angle tanθ=34θ=36.869°Steel rod length L=6 m or 6000 mmAsteel=500 mm2…

Q: "Prob. 3.3-10. A 12-ft beam AB that weighs W, 180 lb supports an air conditioner that weighs W, =…

A: Given that: Length of the beam = 12 ft = 144 in Wa = 1000 lb, Wb = 180 lb It is required to…

Q: 3* The 1/2-in.-thick bar with semicircular (d/r = 1) edge grooves, shown in Fig. P5-83, is made of…

Q: Q2: Steel railroad reels 10 m long are laid with a clearance of 3 mm at a temperature of 15°C. At…

Q: - The rod shown with segment made of steel and copper experienced a 50°C raised in temperature.…

A: Given data for steel bar Ls = 0.5 m Ds = 75 mm Es = 200 GPa αs = 11.7*10-6 m/m-oC for copper bar…

Q: A bronze bar 3 m long with a cross sectional area of 320 mm2 is placed between two rigid walls as…

A: Given: Length of the beam (L)=3m Cross-sectional area (A)=320mm2 Initial Temperature (T1)=-20°…

Q: 11. A boiler shell 200 cm diameter and plate thickness 1.5 cm is subjected to internal pressure of…

Q: 215. A uniform concrete slab of total weight W is to be attached, as shown in Fig. P-215, to two…

A: Given data Weight of slab = W To determine The ratio of area of cross-section of rods so that…

Q: Calculate the combined stress (MPa) on the rod shown below using the principle stress method. Here,…

Q: A flat plate with a central hole is subjected to an axial tensile force F of 9.8 KN, as shown in the…

A: Given:F=9.8 KNSyt=75 N/mm2w=10 cm =100 mmd=3 cm =30 mm

Q: 2.78 The bronze bar 3 m long with a cross-sectional area of 350 mm² is placed between two rigid…

Q: : The homogeneous bar ABCD shown in Fig., is -ported by a cable that runs from A to B around the…

A: ∑FH=0TAB cos 30°=RD sin 50°RD= 1.1305 TAB∑FV=0TAB sin 30°+TAB+TC+RD cos 50°=WTAB sin…

Q: A rigid horizontal bar of negligible mass is connected to two rods as shown in Fig. P- 275. If the…

A: As per given question Copper L=3m A= 1500mm2 E=120gpa α=16.8 m°c Brass L=2m A=1200mm2 E=100gpa…

Q: 2A. A copper rod and two steel rods together support a load of W=410 kN as shown in figure. The…

A: Given data as per question Load (W)=410 KNArea of copper rod =2000 mm2Area of steel rod=1000…

Q: The length of a cylindrical pressure vessel is 4 m. The ends are closed with flat plates. When…

Q: Determine the total pull exerted by the cold bar and the intensity of stress in it. Use E = 200 GPa

A: Determine total pull exerted by the cold bar and the intensity of stress in it

Q: Torsion of bars with thin-walled open cross sections. Consider a bar with the cross section shown in…

A: TORSION OF BARS WITH THIN WALLED OPEN CROSS SECTIONS In the customary speculations of twist of…

Q: Calculate the combined stress (MPa) on the rod shown below using principle stress method. Here, FI…

A: Given data:F1=0.35KN T=42800Nmm diameter=75mmF2=0.12KN length=75cmTo…

Q: As shown in Fig, there is a gap between the aluminum bar and the rigid slab that is supported by two…

A: Given data as per question Area of copper rod =500 mm2 Area of aluminium rod =400 mm2 we know that…

Q: . A leather belt 125 mm wide and 6 mm thick, transmits power from a pulley 750 mm diameter which…

Q: A steel bar 600mm long and having 30mm diameter, is turned down to 25mm diameter for one fourth of…

A: Given data: L=600 mmd=30 mm∆T=30°Cα=12.5×10-6/°CE=200 GN/m2

Q: The length of a cylindrical pressure vessel is 4 m. The ends are closed with flat plates. When…

Q: I need to solve this question

A: Write the given information.

Q: L = 3 m Figure P-265

Q: A flat plate with a central hole is subjected to an axial tensile force F of 12 KN, as shown in the…

A: Given Data : Force F = 12 KN Tensile Stress Syt = 70 N/mm2 width w = 8cm diameter d = 4 cm radius r…

Q: Four steel bars jointly support a mass of 25 x 103 kg. Initially the temperature is 250C. Bars A and…

A: h = 800 mm m = 25000 kg T1 = 25 oC T2 = 60 oC Cross-sectional area of A = Cross-sectional Area of D…

Q: b) A composite bar is shown in figure Qlb. Determine. The thermal stresses in copper tube and steel…

A: As we know that due to temperature rise there must be increase in length according to its…

Q: 7. A rigid bar ABC is pinned at A and is connected by steel bar CE and a copper bar BD as shown. If…

A: δ1 -> change in length of copper rodδ2 -> change in length of steel rodBy…

Q: A rigid bar of negligible weight is supported as shown in Fig. P-271. If W = 80 kN, compute…

Q: Q2. An alloy circular bar ABCD 8 m long is subjected to a tensile force of 70 kN, as shown in figure…

A: Introduction: Internal forces are generated within the body as a result of the imposed load. This…

Q: Bar properties 450 mm Determine the internal forces and normal 500 mm? A1 = E, = stresses in bars…

A: -

Q: ABC element with rectangular section shown in the figure is in the (x-z) plane. Find the point at…

Q: A thick cylinder 10 cm inner diameter and 17-5 cm outer diameter and closed at the ends is subjected…

A: Internal fluid pressure is known to be applied to a thick cylinder with a 10 cm inner diameter and a…

Q: A ring is made of a 5 cm diameter round bar as shown in Fig. 8-14. Całculate the stresses at point A…

A: We know that a ring is built of a 5 cm diameter round bar, as indicated in the diagram, and we need…

Q: A flat plate with a central hole is subjected to an axial tensile force F of 9.8 KN, as shown in the…

Q: A rigid bar of negligible weight is supported as shown in Fig. P-271. If W = 80 kN, compute the…

Q: Four steel bars jointly support a mass of 15 Mg as shown in Fig. P-276. Each bar has a…

A: As per given question α=11.7 m•c E=200gpa ΔT=50°c We have to find load carried by each bar

Q: QI A rigid bar ABCD is pinned at end A and supported by two cables of equal length at points B and C…

Q: An axial pull is acting on a bar consisting of two different materials is shown in figure.If the…

Q: ) While removing a wheel to change a tire, a driver applies forces P=111 N at the ends of two of the…

Q: A steel rod is stretched between two rigid walls and carries a tensile load of 4,075 N at 20°C. If…

A: Now write the net elongation in the rod due to mechanical load and thermal load.

Q: 105. For the truss shown in Fig. P-105, determine the cross-sec- tional areas of bars BE, BF, and CF…

Q: A rigid bar AB is hinged at A and supported by copper rod 2 m long and steel rod i m long as shown…

Q: The concrete post (Ec = 30 GPa and a =10x10/C) is reinforced with six steel %3D -6 o bars, each of…

Q: As shown in the figure, there is a gap between the aluminum bar and the rigid slab that is supported…

Q: A solid circular bar of steel (G = 78 GPa)transmits a torque T = 360 N ? m. The allowablestresses in…

Q: A rigid block having a mass 5 Mg is supported by three rods symmetrically placed, as shown in the…

A: Given Data : Mass m = 5 Mg Temperature T = 40 oC Modulas of Elasticity Es=200 GPa αs = 11.7 μm/mC…

Q: An axial pull of 35000N is acting on a bar consisting of three lengths as shown in fig above. if…

Q: If a copper ring with an outer diameter of 2000 mm and a thickness of 20 mm and a steel ring with an…

A: Given,

Concept explainers

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.

Question

100%

A homogeneous 800 kg bar AB is supported at either
end by a cable as shown in Fig. P-105. Calculate the
smallest area of each cable if the stress is not to exceed
90 MPa in bronze and 120 MPa in steel.
Figure P-105
Bronze
L= 4 m
Steel
L= 3 m
10 m

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1 Introduction

VIEW

Step 2 Solution

VIEW

Step 3 Result

VIEW

Trending now

This is a popular solution!

Step by step

Solved in 3 steps with 1 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, mechanical-engineering and related others by exploring similar questions and additional content below.

Similar questions

A horizontal rigid bar of weight If' = 72001b is supported by three slender circular rods that are equally spaced (see Figure)'. The two outer rods are made of aluminum (£-, = 10 X 10 psi) with diameter f/j = 0.4 in. and length Ly= 40 in. The inner rod is magnesium {F-, = 6.5 X 10* psi) with diameter rf, and length L-,. The allowable stresses in the aluminum and magnesium are 24,000 psi and 13,000 psi, respectively. IF it is desired to have all three rods loaded to their maximum allowable values, what should be the diameter d2and length LzoF the middle rod?
- A specimen used in a coupon test has norm al stress ??. = 15 MPa (see figure). Using Mohr’s circle, find the state of stress on the element oriented at angle ? = 20° and show the full stress state on a sketch of a properly oriented element.
A circular copper bar with diameter d = 3 in. is subjected to torques T = 30 kip-in. at its ends. Find i lie maximum shear, ion si le. and compressive stresses in the tube and their corresponding strains. Assume that G = 6000 ksi.
A spherical balloon is filled with a gas. The outer diameter of the balloon is 20 in. and the thickness is 0,012 in. Calculate the maximum permissible pressure in the balloon if the allowable tensile stress and the allowable shear stress in the balloon are 1 ksi and 0.3 ksi, respectively.
Two bars AC and BC of the same material support a vertical load P (see figure). The length L of the horizontal bar is fixed, but the angle fl can be varied by moving support A vertically and changing the length of bar AC to correspond with the new position of support A. The allowable stresses in the bars are the same in tension and compression. When the angle ft is reduced, bar AC becomes shorter, but the cross-sectional areas of both bars increase because the axial forces are larger. The opposite effects occur if the angle 0 is increased. Thus, the weight of the structure (which is proportional to the volume) depends upon the angle ft. Determine the angle ft so that the structure has minimum weight without exceeding the allowable stresses in the bars. Note: The weights of the bars are very small compared to the force P and may be disregarded.
A steel cable with a nominal diameter of 25 mm (see Table 2-1) is used in a construction yard to lift a bridge section weighing 38 kN. as shown in the figure. The cable has an effective modulus of elasticity E = 140 GPa. (a) If the cable is 14 m long, how much will it stretch when the load is picked up? (b) If the cable is rated for a maximum load of 70 kN, that is the factor of safety with respect to failure of the cable?
A single steel strut AB with a diameter (a) Find the strut force Fs and average normal stress ds= 8 mm supports the vehicle engine hood of a in the strut. mass 20 kg that pivots about hinges at C and D (see (b) Find the average shear stress t aver in the bolt at A,figure parts a and b). The strut is bent into a loop at (C) Find the average bearing stress bon the bolt at A. its end and then attached to a bolt at A with a diameter db= 10 mm. Strut AB lies in a vertical plane.
A circle of a diameter d = 200 mm is etched on a brass plate (see figure). The plate has dimensions of 400 x 400 x 20 mm. Forces are applied to the plate, producing uniformly distributed normal stressescr^ =59 MPaander^ = —17 MPa. Calculate the following quantities: (a) the change in length Aac of diameter at: (b) the change in length Abd of diameter bd; (c) the change At in the thickness of the plate; (d) the change AV in the volume of the plate; (e) the strain energy U stored in the plate; (f) the maximum permissible thickness of the plate when strain energy £/must be at least 784 J; and (g) the maximum permissible value of normal stress axwhen the change in volume of the plate cannot exceed 0.015% of the original volume. (Assume E = 100 GPa and v = 0.34
A pressurized circular cylinder has a sealed cover plate fastened with steel bolts (see figure). The pressure P of the gas in the cylinder is290psi, the inside diameter D of the cylinder is 10.0 in., and the diameter dBof the bolts is 0.50 in. I f the allowable tensile stress in the bolts is 10,000 psi, find the number n of bolts needed to fasten the cover.
,10-6 A prismatic bar with a diameter d0= 20 mm is being compared with a stepped bar of the same diameter(d| = 20 mm) that is enlarged in the middle region lo a diameter d2= 25 mm (see figure). The radius of the fillets in the stepped bar is 2.0 mm. (a) Does enlarging the bar in the middle region make it stronger than the prismatic bar? Demonstrate your answer by determining the maximum permissible load for the prismatic bar and the maximum permissible load F, for the enlarged bar, assuming that the allowable stress for the material is 80 MPa. (b) What should be the diameter d0of the prismatic bar if it is to have the same maximum permissible load as does the stepped bar?
A hollow, circular, cast-iron pipe (Ec =12,000 ksi) supports a brass rod (Ec= 14,000 ksi} and weight W — 2 kips, as shown. The outside diameter of the pipe is dc= 6 in. (a) If the allowable compressive stress in the pipe is S00O psi and the allowable shortening of the pipe is 0.02 in., what is the minimum required wall thickness trmm? (Include the weights of the rod and steel cap in your calculations.) (b) What is the elongation of the brass rod Srdue to both load Wand its own weight? (c) What is the minimum required clearance h?
A bar AB of length L and weight density y hangs vertically under its awn weight (see figure). The stress-strain relation forth? Material is given by the Romberg-Osgood equation [Eq. (2-71)]: Derive the formula For the elongation of the bar.