A hollow square steel tube has a height and width dimension of 4 in and a wall thickness of 0.45 in. and an original length of 8 in. The tube is loaded with 45000 lb. in compression and is shortened by 0.0035 in. as a result of the load. Determine the Modulus of Elasticity of the steel with 1-decimal place accuracy. ↑ Height (mm) Wall (mm) Width (mm)

A hollow square steel tube has a height and width dimension of 4 in and a wall thickness of 0.45 in. and an original length of 8 in. The tube is loaded with 45000 lb. in compression and is shortened by 0.0035 in. as a result of the load. Determine the Modulus of Elasticity of the steel with 1-decimal place accuracy. ↑ Height (mm) Wall (mm) Width (mm)

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Q1- The rigid bar of negligible weight is supported as shown in Fig- IS W- 80 kN, compute the temperature change of the assembly that will cause a tensile stress of 50 MPa in the steel rod. Use the following data: Bre Steel 15 m A (mm') a (/c°) 110m E (GPa) Steel rod 300 Bronze rod 1400 11.7* 10* 200 18.9 10 25m 83
Find the tension of the cord that extends from point C to D and compute for stress experienced by the cable if it's diameter in 1.51 in2. Neglect the members weight and friction. Round-off your answer into the nearest whole number. 150 Ib/ft 6 ft ft 6 ft 12 ft ft ANS: T = Ib, Stress = ksi
A solid aluminum shaft of 100 mm diameter fits concentrically in a hollow steel tube. Determine the minimum internal diameter in mm of the steel tube so that no contact pressure exist when the aluminum shaft carries an axial compressive load of 503 KN. Assume Poisson's ratio = 1/3 and a modulus of elasticity of the aluminum rod is 75 GPa. Use 4 decimal places. Add your answer
A steel pipe has an inside diameter of d = 250 mm and an outside diameter of D = 268 mm. The length of the pipe is L = 6.0 m. The changes in dimension caused by an increase in temperature of 80°C for the: Outside diameter - Blank 1 mm Inside diameter - Blank 2 mm Lenght - Blank 3 mm Note: All answer must be round off up to 3 decimal places.
2. A spherical stainless-steel tank having an inner diameter 'D', is used to store natural gas at a pressure of 'p'. The properties of the steel are as follows: yield stress in tension is "T'; yield stress in shear is 'S' and modulus of elasticity is 'E'. The desired factor of safety with respect to yielding is F.S'. Determine the minimum permissible thickness tmin Of the tank. D=500mm, p=19MPA,T=970MPA,S=500Mpa,E=196GPA,F.S=2.8 ww.
In this figure is a strut and a cable which was used to lift a body, if the strut and a cable has a stress equivalent to your SN and MN in kips respectively, determine the maximum weight of that body. Neglect the weight of wood and cable. Note: Round off your answer in two decimal places. ... Cable (A = 0.5 in 2) 9 ft C B 12 ft Weight A Wood Strut ( A 16 in 2)
A column is fabricated by adhesively bonding two aluminum faceplates to a foam plastic core as shown below. Note that there are only left and right aluminum plates (with no front and back plates). The foam plastic core has a square cross-section with elastic modulus Ef 1110 MPa. Determine the stress in the aluminum plates, the stress in the foam core, and the displacement of the column under the action of the applied force. = Note: Express tensile stresses as positive (+) and compressive stresses as negative (-). Given: • L1 L2 = = 100 mm = 1.7 m • . L3 = = 1.4 mm RIGID PLATE ALUMINUM FACE PLATE F FOAM L2 |← 41 +| |—–—– 63 L1 L3 F = 37 kN σα = σ f = |ɗ| = = number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) number (rtol=0.01, atol=1e-05) MPa ? MPa mm ?
Find the tension of the cord that extends from point C to D and compute for stress experienced by the catble if it's diameter in 1.51 in? Neglect the members weight and friction Round-off your answer into the nearest whole number 150 Ib/ft 6 ft 8 ft 6 fh -12 ft
3. A sheet of plywood consists of three equally thick sheets, the upper and lower sheets having their grain in the same direction and the middle sheet with its grain at right angles. The wood have a tensile modulus for forces in the direction parallel to the grain of 10 GPa and in the transverse direction0.4 GPa. Determine the tensile modulus of the laminate when loaded in a direction parallel to the grain directon of the outer sheets.
Find the thickness of a metal needed of the semi-spherical end of cylinder vessel 0.70 meter in diameter to an internal pressure of 2.70 N/mm2. The material is mild steel and tensile is 69 N/mm2
A bar, 12 mm in diameter is acted upon by an axial load of 20 kN. The change in diameter is measured as 0.03 mm. DeterminePoisson’s ratioYoung’s modulusBulk modulus Assume modulus of rigidity as 80 GPa
The homogeneous bar ABC is supported by a pin at C and a cable that runs from A to B around the frictionless pulley at D. Find the stress (in psi) in the cable if its diameter is d = 0.51 in and the weight of the bar is 5298 lb. Round off the final answer to three decimal places.