A high-voltage power line is attached toan insulator which is held by three bars.The tensile force Z in the sagging powerline at the insulator is to 1000 N.3.Determine in 3 decimals and inNewtons the force in bar 12a2.1За15°15°B Z

Answered: A high-voltage power line is attached…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The force applied at the handle of the rigid lever causes the lever to rotate clockwise about the pin B through an angle of 2°. Determine the average normal strain in each wire. The wires are unstretched when the lever is in the horizontal position. 200 mm 200 mm 300 mm -300 mm- E B D 200 mm H
The steel pipe (G - 75GPA) has an outer diameter of 50mm and an inner diameter of 30mm. It is fixed at A and three torques are applied to it as shown. Solve the rotation of the free end with respect to the fixed end. 200mm 250mm 300mm 30 N-m 20 N.m 80 N-m O 0.000749rad O 0.000674rad O 0.00624rad O 0.00142rad
The thin plate ABCD of mass 8 kg is held in the position shown by the wire BH and two links AE and DF. Neglecting the mass of the links, determine immediately after wire BH has been cut (a) the acceleration of the plate, (b) the force in each link. H. E 150 mm 30% A B F 200 mm 30 D. IC 500 mm
2. The plate is acted on by four parallel forces, three of which are shown. The fourth force P and its line of action are unknown. The resultant of this force system is the couple-vector. (-1100i + 1500J)lbft. Determine P and its line of action. %D 1400 lb 200 lb 300 1b y 2. ft 3 ft 3 ft 4 ft
3. The length of 2-mm diameter steel wire CD has been adjusted so that with no load applied, a gap of 1.5 mm exists between the end B of the rigid beam ACB and a contact point E. If E = 200 GPa, determine where a 20 kg block should be placed on the beam in order to cause contact between B and E. D X 0.25 m 20 kg A 1.5 mm C 0.08 m 0.32 m E
Question Bank - Friction The two homogeneous bars AB and BC are connected with a pin at B and placed between rough vertical walls. If the coefficient of static friction between each bar and the wall is 0.4, determine the largest angle 0 for which the assembly will remain at rest. 600 mm 6N 600 mm 8 N A. Technology Druen by fanoation Tips: 6N force and 8N force are acting vertically by gravity at the center of the material. Expose the forces acting between the bars and the wall (F and N) Check which interaction will first impend sliding - then expose if free body diagram from the internal hinge at B. e =? Answer in ° (1-2 Decimals are accepted)
EXAMPLE 4.7 Two cylindrical rods, one of steel and the other of brass, are joined at C and restrained by rigid supports at A and E. For the loading shown and knowing that E.= 200 GPa and E.= 105 GPa, determine (a) the reactions at A and E, (b) the deflection of point C. Dimensions in mm 100 100 -180-- Dl E Steel Be 60 kN Brassc 40 kN 40-mm diam. 30-mm diam.
The force applied at the handle of the rigid lever causes the lever to rotate clockwise about the pin B through an angle of 2°. Calculate the average normal strain developed in each wire. The wires are unstretched when the lever is in the horizontal position. A T 200 mm 200 mm B -300 mm- 200 mm D 300 mm E
■ Determine the maximum tension force T for the three cases in the figure. ■ Consider only the resistance from the angle. 100 myn 5275 tomm TEM 10mm I 1/20mm Typical хот tom томил Вотик Вэтаа Somm T T
A. The resultant of the four belt tensions and couple C is force R acting through points O. 1. What is the value of R? 2. What is the value of C? 1000 N 30 mm 200 N 400 N
What is the fixed end moment at A? 10 kN 3kN/m D 3m B 4 m 4 m
answer sheet. 1. A tower guy wire is anchored by means of a bolt at A. The tension in the wire is 4000 N. Determine the angles 0x, ey, 0,defining the direction of the force. B 80 m 40 m 30 m

SEE MORE QUESTIONS

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS

A high-voltage power line is attached to an insulator which is held by three bars. The tensile force Z in the sagging power line at the insulator is to 1000 N. 3. Determine in 3 decimals and in Newtons the force in bar 1 2a a. 2. A 1 За 15° 15° B Z