A folding tray mechanism is attached to a wall as shown. Find the internal forces and bending moment inthe lower support arm at section s-s, located midway between points B and E, when a force of F = 270 N isapplied at an angle of 0 = 28°.2013 Michael SwanbomⒸ030BY NC SAk s-ŚabGсh₁h₂каES-BValues for dimensions on the figure are given in the following table. Note the figure may not be to scale.Variable Value16 cm19 cm25 cm23 cm17 cmThe internal axial load at section s-s is A =The internal shear load at section s-s is V =The internal bending moment at section s-s is M =N.N.C.N-m.0

To find: (a) The internal axis load at section s-s. (b) The internal shear load at section s-s. (c)…

A folding tray mechanism is attached to a wall as shown. Find the internal forces and bending moment in the lower support arm at section s-s, located midway between points B and E, when a force of F= 270 N is applied at an angle of 0-28°. 2013 Michael Swanbom *5. h₁ a b G с h₁ h₂ E b Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value 16 cm 19 cm 25 cm 23 cm 17 cm The internal axial load at section s-s is A -| The internal shear load at section s-s is V- The internal bending moment at section s-s is M - B N. N. N-m.

A folding tray mechanism is attached to a wall as shown. Find the internal forces and bending moment in the lower support arm at section s-s, located midway between points B and E, when a force of F= 270 N is applied at an angle of 0-28°. 2013 Michael Swanbom *5. h₁ a b G с h₁ h₂ E b Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value 16 cm 19 cm 25 cm 23 cm 17 cm The internal axial load at section s-s is A -| The internal shear load at section s-s is V- The internal bending moment at section s-s is M - B N. N. N-m.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter1: Tension, Compression, And Shear

Section: Chapter Questions

Problem 1.9.17P: A sign of weight W is supported at its base by four bolls anchored in a concrete footing. Wind...

See similar textbooks

Similar questions

Solve the preceding problem for the following data: b = 8.0 in., k = 16 lb/in., a = 45°, and P = 10 lb.
A wine of length L = 4 ft and diameter d = 0.125 in. is stretched by tensile forces P = 600 lb. The wire is made of a copper alloy having a stress-strain relationship that may be described mathematically by =18,0001+30000.03(=ksi) in which is nondimensional and has units of kips per square inch (ksi). (a) Construct a stress-strain diagram for the material. (bj Determine the elongation, of the wire due to the Forces P. (c) IF the forces are removed, what is the permanent set of the bar? (d) If the forces are applied again, what is the proportional limit?
Repeat the preceding problem using sx= 5.5 MPa. ??y= 4 MPa. and txy= 3.2 MPa.
Solve the preceding problem for the following data:P = 160 kN,JV = 200 tN,L = 2 m,b = 95 mm, h = 300 mm, and d = 200 mm
A sign of weight W is supported at its base by four bolls anchored in a concrete footing. Wind pressure P acts normal to the surface of the sign; the resultant of the uniform wind pressure is force fat the center of pressure (C.P). The wind force is assumed to create equal shear forces F/4 in the y direction at each boll (see figure parts a and c). The overturning effect of the wind force also causes an uplift force R at bolts A and C and a downward force (— R) al bolts B and D (see figure part b). The resulting effects of the wind and the associated ultimate stresses for each stress condition are normal stress in each boll (h — 60 ksi); shear through the base plate (th = 17 ksi); horizontal shear and bearing on each bolt ( tfur = 25 ksi and cr^ = 75 ksi): and bearing on the bottom washer at B (or D) (abor = 50 ksi).
Solve the preceding problem for the following data: b = 6 in., b = 10 in, L = 110 ft, tan a = 1/3, and q = 325 lb/ft.
A folding tray mechanism is attached to a wall as shown. Find the internal forces and bending moment in the lower support arm at section s-s, located midway between points B and E, when a force of F = 250 N is applied at an angle of 0 = 32°. A B. 's E D k a- b – Values for dimensions on the figure are given in the following table. Note the figure may not be to scale. Variable Value a 17 cm b 26 cm 35 cm hi 25 cm h2 18 cm The internal axial load at section s-s is A = N. The internal shear load at section s-s is V = N. The internal bending moment at section s-s is M = N-m.
:Q81 The moment M for the force the figure shown below is 250 N 153 -200 mm 30 mm 46.5 N.M O 46.6 N.M O 46.4N. M of L is
Figure 1.5 m 2 m 2m 0.5m B 2 1m 2.5 m 4 m 1 of 1
11:11 A The wood beam has an allowable shear stress of Tallow = 9.6 MPa. d3 d3 Variable d₁ d₂ d1 d3 d4 d5 wamap.org Value d2 V Values for the figure are given in the following table. Note the figure may not be to scale. 0.05 m 0.125 m 0.05 m 0.225 m P 0.1125 m d1 d5 a. Determine the Q at point P. b. Determine the moment of inertia, I. d4 c. Determine the magnitude of the max shear force that can be applied to the cross-section at point P, Vmax.
Review Learning Goal: To use the vector cross product to calculate the moment produced by a force, or forces, about a specified point on a member. Part A - Moment due to a force specified by magnitude and endpoints The moment of a force F about the moment axis passing through O and perpendicular to the plane containing O and F can be expressed using the vector cross product, Mo =r x F. In a properly constructed Cartesian coordinate system, the vector cross product can be calculated using a matrix determinant: As shown, a member is fixed at the origin, point O, and has an applied force F, the tension in the rope, applied at the free end, point B. (Figure 1) The force has magnitude F = 180 N and is directed as shown. The dimensions are ¤1 = 0.350 m, x2 = 1.90 m, y1 = 2.30 m, and z1 = 1.20 m. What is the moment about the origin due to the applied force F? i j M =rx F =|rz k Express the individual components of the Cartesian vector to three significant figures, separated by commas. ry F F,…
Use the method of SECTIONS to find the true magnitude and direction in bar HG of the truss shown below in Fig 3.5 -500lb -100lb A 45° -200lb H -100lb 2 B -200lb -200lb MAGNITUDE AND DIRECTION OF SUPPORTS -500lb H -100lb 45° 2¹ C2D 2¹ Fig 3.5. -200lb -100lb LI 2 B 2₁ 2₁ D 2₁ E