A floor sheathing is supported by 75 mm x 250 mm wooden joists of unknown spacing. The joist has an effective span of 3.75 m. The total floor load transmitted by the sheathing to the joist is at 4.75 kPa. Using the weight of wood Modulus of elasticity E = 13800 MPa. Allowable bending stress is 15.8 MPa. with the allowble shear stress equal to Design the spacing of the floor joist if deflection limit is 6.00 KN/m² 0.90 MPa. L / 350. Floor Sheathing Floor Joist boina Vint

A floor sheathing is supported by 75 mm x 250 mm wooden joists of unknown spacing. The joist has an effective span of 3.75 m. The total floor load transmitted by the sheathing to the joist is at 4.75 kPa. Using the weight of wood Modulus of elasticity E = 13800 MPa. Allowable bending stress is 15.8 MPa. with the allowble shear stress equal to Design the spacing of the floor joist if deflection limit is 6.00 KN/m² 0.90 MPa. L / 350. Floor Sheathing Floor Joist boina Vint

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A simply supported beam is reinforced with 5-25mm at the bottom And 2-20mm at the top if the beam. Concrete covering to centroid of reinforcement is 70mm at the top and 64 mm at the bottom. The beam has a gross depth of 450 mm and gross width of 300 mm. Fc’=28 mpa fy= 415 mpa. Assume bars are laid out in a single layer. calculate the following if the limiting tensile steel strain is 0.004 for ductile failure: a) depth if neutral axis from the extreme concrete compression fiber ( in mm, in whole number) b) design strength of the beam section ( in kn•m , in whole number) c) maximum service uniform live load over the entire span in Addition to a DL = 20 kn/m ( including weight of the beam) if it has a span of 6 m ( in kn, in whole number)
A concrete floor slab 10e mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.0 m, web width of 250 mm and overall depth of 500 mm. The tensile reinforcement consists of 6-020 mm bars in two rows with 25 mm vertical clear spacing. Use material strengths f'c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = Depth of uniform stress block at ultimate stage in mm to the nearest whole number = Tensile steel strain compatible with concrete strain of 8.003 in 3 decimal places =
A beam cast monolithically has the following properties: bf=1200mm, t or hf = 110mm, bw=380mm and h=800mm. It is reinforced with 10D32mm grade 420MPa bars. Concrete strength is assumed to be 27.5MPa and the centroid of tension reinforcement is located 665mm from the outermost compression fiber. A. Determine maximum nominal moment to ensure tension controlled, kN-m. B. Calculate the balanced steel area, mm2. C. Calculate the balanced moment in kN-m.
Determine the minimum dimension a to the nearest mm of the beam's cross section safely support the load.The wood has an allowable normal stress of 10 MPa and an allowable shear stress of 1 MPa.
A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.2 m, web width of 250 mm and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm diameters bars in two rows with 25 mm vertical clear spacing. Use material strengths f'c = 21 MPa and fy = 415 Mpa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm Depth of uniform stress block at ultimate stage in mm to the nearest whole number Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places
Situation 17: A rectangular beam has a width of 300mm and an effective depth to the centroid of the tension reinforcement of 600mm. The tension reinforcement has an area of 4762mm2 and the area of compression reinforcement placed 62.5mm from the compression face of the beam is 987.5mm2 fy=414.6 MPa, fc’=34.56 MPa. Balanced steel ratio is 0.034. Assume that steel yields. Determine the depth of compression block. Determine the design strength. Determine the concentrated live loads at the midspan in addition to a dead load of 20kN/m including the weight of the beam if it has a span of 6m.
A concrete floor slab 100 mm thick is cast monolithic with concrete beams 2.0 m on centers. The beams have a span of 4.0 m, web width of 250 mm and overall depth of 500 mm. The tensile reinforcement consists of 6 - ø20 mm bars in two rows with 25 mm vertical clear spacing. Use material strength f'c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry: Effective flange width of an interior beam in mm = _______ Depth of uniform stress block at ultimate stage in mm to the neares whole number = _______ Tensile steel strain compatible with concrete strain of 0.003 in 3 decimal places = __________
The wood beam has an allowable shear stress of tallow = 7 MPa. Determine the maximum shear force V that can be applied to the cross section.
concrete floor slab 100 mm thick is cast monolithic with concrete beam 2.0 m on centers. The beams have a span of 4.2 m and have a web width of 250 mm, and overall depth of 450 mm. The tensile reinforcement consists of 4-25 mm bars in two rows with 25 mm vertical clear spacing. Use material strength f’c = 21 MPa and fy = 415 MPa. Calculate the following considering a T-geometry; a) effective flange width of an interior beam in mm b) depth of uniform stress block at ultimate stage in mm ( round of to nearest whole number) c) tensile steel strain compatible with concrete strain if 0.003 ( round if 3 decimal places)
1. Figure shows two wood members are joined together using a 60 degrees wood glue adhesive. Find the average normal and shear stress resisted in the plane of the connection. 25 mm 8 kN- 8 kN 60° 30 mm
The wood beam has a square cross section. Find the smallest allowable cross-sectional dimensions if the working stresses are 8 MPa in bending and 1.0 MPa in shear | 5 kN 2 kN • m A D В +1.0 m –1.0 m →|
Seatwork The beam shown is prestressed by using a bonded (stress relieved tendons) with a specified tensile strength of prestressing tendons strength fpu=1350 MPa, fc'=35 MPa. The area of prestressed reinforcement in tension zone Aps=1000 mm?. The specific yield strength of prestressing tendons sd, foy=1160 MPa. а. What is the value of the stress in prestressed reinforcement at nominal strength (Aps) b. What is the value of the depth of the compression block. С. What is the ultimate moment capacity of the prestressed beam. 0.85fc' 430 NA |(d-a/2) · A=1000 T=Ap.Sps 250