A floating column AB of length L, is modelled with top end fixed and bottom end yielding under column load. The yielding support can be visualised as an axial spring of stiffness k. If an axial force Pis applied at a distance 'a' from the top, determine reactions at the ends A and B and displacement at the end B.

A floating column AB of length L, is modelled with top end fixed and bottom end yielding under column load. The yielding support can be visualised as an axial spring of stiffness k. If an axial force Pis applied at a distance 'a' from the top, determine reactions at the ends A and B and displacement at the end B.

Mechanics of Materials (MindTap Course List)

9th Edition

ISBN:9781337093347

Author:Barry J. Goodno, James M. Gere

Publisher:Barry J. Goodno, James M. Gere

Chapter10: Statically Indeterminate Beams

Section: Chapter Questions

Problem 10.4.10P: Beam AB has a pin support at A and a roller support at B Joint B is also restrained by a linearly...

See similar textbooks

Similar questions

Beam AB has a pin support at A and a roller support at B Joint B is also restrained by a linearly elastic rotational spring with stiffness kR, which provides a resisting moment MBdue to rotation at B. Member AB has flexural rigidity EI. A moment M0acts counterclockwise at B. Use the method of superposition to solve for all reactions. Find an expression for joint rotation Ain terms of spring stiffness kR. What is Awhen kR 0? What is Awhen kR— ? What is Awhen kR= 6EI/L?
1. A helical compression spring is made of hard-drawn spring steel wire with a wire diameter d = 0.080 in and an outer coil diameter OD = 0.880 in. The ends are plain and ground, and there are 8 total coils. Determine the force F, required to close the spring, the spring constant k, the free length of this spring corresponding to n, = 1.2, and the pitch p.
CE is a 10 m beam supported at point E by a ball and socket joint. Ball and socket joints provide reaction forces, but not reaction moments. D is at the midpoint between C and E. A horizontal force of -100 j is applied at point D. Two ropes are attached to point C, with unknown tensions TA and TB. Point A is at (4, 6, 0) while point B is at (-3, 4, 0). The system is in equilibrium. Find the magnitude of the tensions TA and TB. ITAI = |TB| = N N
Situation 5 - The crane shown in Figure AP-4.13 carries the load W. The crane is hinged at B and supported by a flexible cable AC. For this problem, x1 = 10 m, x2 = 8 m, and h = 18 m. The load W is 20 kN. 13. What is the tension in the cable AC, in kN? Answer: 22.63 kN 14. What is the resultant XI reaction at B in kN? Plgure AP-4.13 Answer: 39.40 kN 15. If the maximum load on the cable is 50 kN, determine the largest value of W in kN. Answer: 44.19 kN
Member AB (helical spring) and Member AC (axial rod) are carrying a weight at point A. Member AB has the following properties: R = 90 mm, n -4 turns, G- 70 GPa, d- 30 mm, and Talow = 105 MPa while Member AC has the following properties: L= 2.A- 500 mm?, E = 200 GPa, and a low- 30 MPa. Determine the maximum safe %3D value of W (in N). Use simplified formula for the helical spring. A 60°
In the figure, AB is a rigid rod and CB is a cable. If M is 900kg, what is the pin reaction at A on the rod AB? What is the tension in the cable?
The système have diferent stiffness (K1 and K2), The column (AB) have both ends pined and the Beam (BC) have one end pined and one end fixed. Find the system équation of the Residual force of the structure (out of balance force), and the Buckling load.
Answer FOUR questions ONLY selecting TWO questions from SECTION A. 1. (a) The vertical structure ABCD shown in Figure 1(a) is subjected to a system of coplanar forces and a moment. The structure is simply supported at D with a frictionless pin and is roller-supported at A. i Sketch the free body diagram (FBD). Take moments about D and hence find the reaction force at support A. ii. 35 AN 23m 60 100 km Osm Figure 1(a) (b) An assembly of a steel bar enclosed within an aluminium alloy tube is shown in Figure 1(b). The tube and the bar are of the same initial length. The combination is compressed between two rigid parallel plates by a force of 500 kN. The diameter of the steel bar is 40 mm, and the inside and outside diameters of the alloy tube are 60 mm and 100 mm respectively. The Young's moduli for steel and aluminium alloy respectively are Est = 200 GNM2, EA = 70 GNm?. Find the stresses generated in the steel bar and the aluminium alloy tube. Sael he -Rid pl Figure 1(b)
Situation 3 - The portable camping tool shown in the Figure AP-4.7 is W E to support weight W at a variable distance x from D. In this problem, L1 = 540 mm, h1 = 240 mm, hz = 120 mm. 7. If W = 2000 N and x = 200 mm. hị Calculate the reaction at B. Answer: 740.74 N 8. If W = 2000 N and x = 200 mm. Calculate the total reaction at pin C in N. Answer: 4529.77 N h2 9. If the breaking strength of the cable FG is 1800 N, determine the ha maximum weight W that can be supported if x = 200 mm? Answer: 761.64N Li Figure AP-4.7
A journal 25 mm in diameter supported in sliding bearings has a maximum end reaction of 2500 N. Assuming an allowable bearing pressure of 5 N/mm², find the length of the sliding bearing
Problem. Consider the following problem. Find the displacement of node 4. Assume F2=200 N, F3=300 N, F4=400 N and Kı= 100, K2= 200, and K3= 300 N/mm. F. 3 2 3 4 Note: The stiffness matrix of individual springs should be first written, then the equilibrium equations at each node should be written, expanded in terms of nodal displacement, and used to perform the assembly of the global stiffness matrix of the problem. Then, the appropriate boundary conditions should be applied and the nodal displacement vector should be found. Every step should be shown; missing any step would result in point deduction even if the final answer is correct.
Q.5 A concentric spring for an aircraft engine valve is to exert a maximum force of 5000 N under an axial deflection of 40 mm. Both the springs have same free length, same solid length and are subjected to equal maximum shear stress of 850 MPa. If the spring index for both the springs is 6,Find:1. The load shared by each spring2. The main dimensions of both the springs3. The number of active coils in each spring.Q.6 A semi-elliptical laminated spring is made of 50 mm wide and 3 mm thick plates. The length between the supports is 650 mm and the width of the band is 60 mm. The spring has two full length leaves and five graduated leaves. If the spring carries a central load of 1600 N,Find :1. Maximum stress in full length and graduated leaves for an initial condition of no stress in the leaves.2. The maximum stress if the initial stress is provided to cause equal stress when loaded.3. The deflection in parts (1) and (2)