A flat steel bar 6 in wide by 1.5 in thick has axial loads applied with 1.250-in diameter pins in double shear at points A, B, C and D as shown in Figure 1. Determine (a) the axial stress in the bar on a cross section 20" to the left of C (b) the average bearing stress on the bar at pin B (c) the cross shearing on the pin at A. 30" 45" 40" 81 Kips DA Bo- Do 45 Kips 54 Kips 18 Kins

A flat steel bar 6 in wide by 1.5 in thick has axial loads applied with 1.250-in diameter pins in double shear at points A, B, C and D as shown in Figure 1. Determine (a) the axial stress in the bar on a cross section 20" to the left of C (b) the average bearing stress on the bar at pin B (c) the cross shearing on the pin at A. 30" 45" 40" 81 Kips DA Bo- Do 45 Kips 54 Kips 18 Kins

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Find max and min stresses. Please provide step by step solution. Don't copy!!
1. The bar ABCD consists of 3 cylindrical steel segments with different lengths and cross-sectional areas. Axial loads are applied as shown. Calculate the normal stress in each segment in psi unit. Indicate if T or C.Calculate the total axial deformation in Problem #1 if Es = 29 x 10 6 psi . Indicate if the bar elongates or contracts.
PROBLEM 3 340 mm The plates are connected by 9-20 mm bolts. Force F = 5Ở KN are applied at both plates in opposite directions as shown in Figure 3. Compute the following: A. Axial stress of each plate. B. Shear stress of each bolt. Assume that each bolt resists the applied force equally. %3D +F 150 mm 中 F 50 mm 340 mm Figure 3: Bolted Plates
Question 4 • h₁-100mm . • h=120mm • t-5mm • b-75mm Z O ko An I beam is subjected to an internal shear force, V, of 325kN. The dimensions for the I-beam are Answer h₁ h Determine the maximum transverse shear stress in the web. Enter your answer in MPa to one decimal place. Your Answer:
As demonstrated, four 25mm diameter rivets with a T=75kN axial load are equally distributed. The plates have a thickness of 25mm and a width of 150mm. determine the following: a. shear stress on the rivetsb. bearing stress between a plate and a rivetc. minimum average tensile stress in each plate strictly draw a complete FBD
PROBLEM 2: What torque can be applied without exceeding the shearing stress of 65 MPa in the botts? Bolt diameter = 12 mm 83 R₁ R2 R₁ = 200.5mm R₂ = 150.5mm 23 = 100.9mm
The steel tie bar shown in Figure 2 is to be designed to carry a tensile force of magnitude P = 30 kips whenbolted between double brackets at A and B. the bar will be fabricated from 0.5* ? inches thick plate. Forthe grade of steel to be used, the maximum allowable stresses are: Normal stress = σn = 25 ksi, Bearingstress = σb = 55 ksi and Shearing stress = τ = 4.5* ? ksi. Solve for the values of (a) the diameter d of thebolt, (b) the dimension b at each end of the bar and (c) the dimension h of the bar.
Which of the following is an allowable stress design concept. O Alternate Basic Load Combinations O OMn O 1.2D+1.6L O Rn = FyAg
6.59 A square section as shown in the figure below is subjected to bending moment M. (c) Obc = Obl y || h y H What is the maximum bending stress? (a) Obc = obt 12M h³ 9M 2h³ JXC h (b) bc = Obt = (d) %bc =%bt = 6M 4³ 9M h³
For the cantilever beam shown. find the value of Normal stress due to axial load at :point F FO ce A 10 m Diameter 100 mm 6 KN.m No stresses at point D 0 -31.229 Mpa +40.99 Mpa -0.25 Mpa +40.49 Mpa No stresses at point F No stresses at point A No stresses at point B +0.25 Mpa +40.74 Mpa No stresses at point C -40.99 Mpa +31.229 Mpa -40.74 Mpa +30.55 Mpa -40.49 Mpa +0.679 Mpa -0.679 Mpa No stresses at point E -30.55 Mpa
A small aluminum alloy [E = 73 GPa] teeshape is used as a simply supported beam as shown. For this beam, a = 150 mm. The cross- sectional dimensions of the teeshape are b = 25 mm, d= 38 mm, and t=7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 490cis measured from a strain gage located at c= 9 rmm below the topmost edge of the tee stem at section 1-1. What is the applied load P? 3P Strain gage d a a H Answer: P = i
A steel pipe is subjected to a quadratic distributed load over its height with the peak intensity go at the base (see figure). q(x) = 90[1-(x/L)²] 90 Assume the following pipe properties and dimensions: height L, outside diameter d = 200 mm, and wall thickness t = 10 mm. Allowable stresses for flexure and shear are ₂ = 117 MPa and T₂ = 40 MPa. (a) If L = 3.5 m, find 90, max (in kN/m), assuming that allowable flexure and shear stresses in the pipe are not to be exceeded. kN/m (b) If q = 80 kN/m, find the maximum height Lmax (in m) of the pipe if the allowable flexure and shear stresses in the pipe are not to be exceeded. m