A flanged bolt coupling is used to connect a solid shaft 94 mm in diameter to a hollow shaft 100 mm in outside and 94 mm in inside diameter. If the allowable shearing stress in the shafts and the bolts is 68.4 MPa, how many 10-mm-diameter steel bolts must be used on a 188-mm- diameter bolt circle coupling so that the coupling will be as strong as the weaker shaft? Round off the final answer to three decimal places.

A flanged bolt coupling is used to connect a solid shaft 94 mm in diameter to a hollow shaft 100 mm in outside and 94 mm in inside diameter. If the allowable shearing stress in the shafts and the bolts is 68.4 MPa, how many 10-mm-diameter steel bolts must be used on a 188-mm- diameter bolt circle coupling so that the coupling will be as strong as the weaker shaft? Round off the final answer to three decimal places.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A flanged bolt coupling consists of 6 - 12 mm - diameter bolts on a bolt circle of 320 mm in diameter. Compute the number of additional 10 mm - diameter bolts on a bolt circle 200 mm in diameter to increase the torque capacity to 7.65 kNm. The shearing stress of the bolts should not exceed 60 MPa. Select one: O a. 6 bolts O b. 4 bolts O c. 3 bolts O d. 2 bolts NEXT PAGE
A bolted connection between a vertical column and adiagonal brace is shown in the figure below. Theconnection consists of three 5/8-in. bolts that join two 1/4-in.end plates welded to the brace and a 5/8-in. gusset platewelded to the column. The compressive load P carried bythe brace equals 8.0k.Determine the following quantities: (a) The averageshear stress τavein the bolts, and (b) the average bearingstress σbbetween the gusset plate and the bolts. (Disregardfriction between the plates.)
Compute the maximum acceptable tensile SERVICE LOAD that may act on a single tee section that is connected to a gusset plate using welds 12 inches long, as shown in the figure. The service live load is three times the dead load. Use A992 steel. USE LRFD ONLY, no block shear will occur. What is the Governing Ultimate Tensile Capacity based on Net Fracture Round your answer to 3 decimal places.
The given plate below with width of 200 mm andthickness of 16 mm is to be connected to two plates ofthe same width with half the thickness by 20 mmdiameter rivets as shown. The rivet hole is 2 mm greaterthan the rivet diameter. Allowable tensile stress on netarea is 0.6Fy. Allowable bearing stress is 1.35Fy. Use a501 plate and a502 gr2 rivet a. Determine maximum load P without exceeding allowable tensile stress on plate b. Determine maximum load P without exceeding allowable shear stress on rivets c. Determine maximum load P without exceeding allowable bearing stress between plates and rivets
The bolted connection shown must support an applied load of P = 5300 kN. The average shear stress in the bolts must be limited to 250 MPa. Determine the minimum bolt diameter that may be used in the connection. Answer: Minimum bolt diameter = i mm
Given the following allowable stresses:• 50 MPa for shear in rivets• 100 MPa for bearing between a plate and a rivet• 80 MPa for tension in the platesDetermine the maximum load P that can be applied to the lap joint connected bythree – 16 mm diameter rivets. Note: Draw its FBD
ll zain IQ 37 MPa no one 10/10 find the tensile stress in upper plate in section 3-3 5 1 4 80 kN 80 kN B-bolt DIA. 10 MM 80 kN 80 kN B-bolt DIA. 10 MM 10 MPa 12.5 MPa 15 MPa 8.5 MPa no one 10/ find the bearing stress between bolts and plate
Topic:Bolted Steel Connection - Civil Engineering *Use latest NSCP/NSCP 2015 formula to solve this problem A lap joint is made up of two steel plates 225mm by 10mm. It is connected by seven rivets having a diameter of 22mm snug fit in the drilled holes. The allowable stresses in the rivets and plates are 110 MPa in shear, 220 MPa n bearing and 138 MPa in tension. Use LRFD. Questions: a) Determine the nominal strength for one bolt due to shear. b) Determine the capacity of the plate based on the gross area and effective area.
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A 100x100x10mm angle is to be welded to a gusset plate. The angle carries a load of 200 kN applied along its centroidal axis which is 28.7 mm above the short leg as shown in the figure. Use an 8 mm fillet weld with a minimum tensile strength Fu=483.33 MPa. Fv = 0.30 Fu Questions: a) Determine the length of a transverse fillet weld along the edge of the angle in order to avoid eccentricity of loading. b) Determine the length of side fillet weld required at the heel. c) Determine the length of side fillet weld required at the toe.
Two plates are held together by 4, 10 mm diameter bolts. If a 26 kN load is applied to the plates in shear, what is the shear stress in the bolts in MPa? Type your answer...
A connection using 3 bolts with the eccentricity is shown in Figure Q3. Determine: (a) Average shear stress for the bolts, (b) Average normal stress between bolt and plate A, and (c) Maximum normal stress in plate B. plat B 12 mm P/2 plat A 25 men. P/2 12 mm 100 mm -P D- 10 mm D- 20 mm Figure Q4
What is the safe load "P" that can be transmitted by the fillet-weld joint shown in figure below if allowable shear stress in the fillet weld is 108 MPa and F.O.S. for load is 1.5? P4 www 60mm 777 50mm 8mm P