Q2:(a) Find and sketch the output of an LTI system whose impulse response, h(t), and input,I(t), are illustrated in figure 2.2.I(t) = e-at u(t)h(t) = u(t)1.50.5t-2246.10An.(b) h(t).(a) z(t).Figure 2: Q2.(b) Find and sketch the output of an LTI system whose impulse response, h[n], and input,z{n], arc given ash[n] = (un)- uja - 3) 5[n)andz(n] 2u[n-3]- 2u[n-6).2u

Convolution Integral-Convolution is used to find the output of any LTI system for any arbitrary…

(a) Find and sketch the output of an LTI system whose impulse response, h(t), and input, I(t), are illustrated in figure 2. (t) = e-atu(t) h(t) = u(t) %3D 15 1 05 0. -2 4. An. 10 (a) z(t). (b) h(t). Figure 2: Q2. (b) Find and sketch the output of an LTI system whose impulse response, h[n], and input, z(n], are given as h[n] = (ua)- uja - 3)) 6(n), %3D and

(a) Find and sketch the output of an LTI system whose impulse response, h(t), and input, I(t), are illustrated in figure 2. (t) = e-atu(t) h(t) = u(t) %3D 15 1 05 0. -2 4. An. 10 (a) z(t). (b) h(t). Figure 2: Q2. (b) Find and sketch the output of an LTI system whose impulse response, h[n], and input, z(n], are given as h[n] = (ua)- uja - 3)) 6(n), %3D and

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

(b) Figure Q1(b) shows the step response for a second-order system. Find its peak time and percentage of overshoot. Hence, obtain its transfer function. 1.6 1.4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 0. 6 10 12 14 16 18 20 22 24 Time (s) Figure Q1(b) Response
Q9 The discrete-time signals x1[n] is shown in the figure. Carefully sketch each of the following signals: a) x1[2n] - u[n-2] b) x1[n]*u[1-n] c) x1[-2n-3] (d) Compute the signal energy 3 2 -1 *x[n] 1 10 1 2 3
e) Compute the integral -3" cos(2u)8(5u - 1)du
A Continuous-time Signal X(t) Is Shown In Figure. Sketch And Label Carefully
The following plot is a step response of a sixth order system. 1. Find the time domain specifications i.e. Tp. Tri. T. and P.O. 2. Find a second order system whose response matches the given response in the following sense a. The percentage overshoot and rise time b. The peak time and settling time c. The rise time and settling time You have to find three systems spred 13) "1 1 aut ON 071 0.3) DA 63) 61 6 2 B Control Systems Homework Problem 3 . 10 12 14 P.O. = e √1-² 100 4 Ts= Con Satisfying 2% criteria 10 18 20 Step Response for 24 The -In (100) 7²+In²(0) Tr 20 P.O. 100 Tp= 2.16+0.60 On 0.3≤ ≤0.8 @n 7 100 1-2 and 10% to 90% value
SHOW, THE CIRCUIT DLAGRAMS BELOW CAL CULATE? (A. ). RT (B) It (c)Pr IT A. 150V C 132 Z02 D * 122 E to (2.) LL
STEADY STATE RESPONSE( NEED NEAT HANDWRITTEN SOLUTION ONLY OTHERWISE DOWNVOTE).
• For the unit step response shown in the figure, find the transfer function of the system. 0.05 0.1 0.15 0.2 0.25 Time (seconds) Response
ii. G(s) = 29 s²+6s+58 a) Find the location of the poles, natural frequency and damping ratio values...... b) Determine the forms and write the general expression for the unit step response. c) Find Css (steady state value) and Peak value:.... d) Revise each transfer function to produce unit step response double approximately two tim slower.....
b) Two circuits connected in series which voltage drop across at each circuit can be expressed in time TTM domain as V1 (t) =5 sin (3147) V and V2 (1) =15 sin (314t - 30°) V. Sketch the waveforms of these voltages to illustrate peak values and phase relationships. UTM 5 UTM UTM TM S UTM UTM TM 5 UTM 8 UTM
Discuss the concept of unit-step, impulse and sinusoidal response and provide at least one example or application. unit-step response: impulse response: sinusoidal response:
This system has an input of a unit step function or u(t). Find: a.) Output Equation c(t) (numerator and denominator) b.) The nature of the response of c(t) ...