(a) Figure Q5(a) shows the A kg box is held in place on the smooth bed of the dump truck by the cable AB. If the angle a= X°, determine the tension in the cable. The parameters A and X depend on your last digit of student's matrix number as shown in Table Q5. Q5 Table Q5 Last digit of your student's matrix number Parameter 0, 2, 4, 6, 8 1, 3, 5, 7,9 A (kg) X (*) 250 300 25 40

(a) Figure Q5(a) shows the A kg box is held in place on the smooth bed of the dump truck by the cable AB. If the angle a= X°, determine the tension in the cable. The parameters A and X depend on your last digit of student's matrix number as shown in Table Q5. Q5 Table Q5 Last digit of your student's matrix number Parameter 0, 2, 4, 6, 8 1, 3, 5, 7,9 A (kg) X (*) 250 300 25 40

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Task II (Equilibrium of A Particle in 3D) In Figure below: A 400 N load is suspended from the ring A. If the load is supported by three cables AB, AC and AD. (Cable AB lies in the x-y plane and cable AC lies on the negative side of the x-axis). A. Determine the force in the cables for equilibrium. B. Write the cartesian vector representation for the forces in the three cables. D 3m 1 m y 30° 3m B 400N
Given: A 3500 lb motor and | 3500 lb plate, as shown, are in equilibrium and supported by three cables and d= 4 ft. 10 ft Find: Magnitude of the tension in each of the cables. В 4 ft `3 ft 3 ft 4 ft Plan: 1) Draw a free body diagram of Point A. Let the unknown force magnitudes be FB, Fc, F D . 2) Represent each force in the Cartesian vector form. 3) Apply equilibrium equations to solve for the 3 unknowns.
Objective 2: Instead of working on Objective 1 yourself, you decide to let a fellow employee perform the task. Of course, mistakes are made, and the employee designs the four- bar mechanism below (units are in feet). Analytically determine the angular displacement of the rocker (Link 4) if the crank (Link 2) is rotated 15° clockwise from the position shown in the image. Use graphical methods to confirm your work. 4.200 4 1.800 105° 0.600 2 3.600
Q2. A 40 lbs lamp is suspended by cables as shown. What are the tensions in each of the 4 cables if the coordinate direction angles for Cable B are a = 120°, ß = 145° and y = 73.68°? Use Matlab or the FY calculator to solve the system of equations. 1 ft Cable C Ift Z Cable B 3ft Cable D 30° 45° Cable A Q3. If each cable in Q2 can sustain a maximum tension of 70 lbs before it breaks, determine the maximum weight of the lamp the cables can support. Q4. A 40 lbs lamp is suspended by cables as shown in Q2. Determine the projected component of the tension in cable A in the direction of cable B. Express the result as a Cartesian vector.
4. Four identical SRS arms are grasping a common object as shown below. Spherical Joint Revolute Joint Find the number of degrees of freedom of this system while the grippers hold the object rigidly (no relative motion between the object and the last links of the SRS arms). Your answer should be an integer. Enter answer here 5. Referring back to Question 4, suppose there are now a total of n such arms grasping the object. What is the number of degrees of freedom of this system? Your answer should be a mathematical expression including n. Examples of mathematical expressions including n are 4 n-7 or n/3.
ASAP
Question 1 The main forces acting on a flying aero plane are the thrust T, the weight W, and the aerodynamics forces namely the lift L and the drag D as shown in the figure Q1. The path of flight is shown by the x-axis. The angle between thrust and path is known as angle of attack and the angle between the horizontal and the path is known as flight path angle. The mass of the aero plane is 72000 kg. At an instant of equilibrium, the lift is 680 kN, the drag is 125 kN and the flight path angle is 6°. Determine the angle of attack and the thrust required to maintain a steady flight. Infer the effect of thrust on the aero plane's weight.
6 m! 1.0 m TS 2 m 3 m 2m 2 m The magnitude of one of the forces is T2 = 80 kN. Find the rectangular representation of T2. * The magnitude of one of the forces is T2 = 80KN. Find the rec tan gular representation of T2. T2 = (-22.86 i + 34.29 / + 68.57 k) N T2 = (-22.86 i – 34.29 j + 68.57 k) N T2 = (22.86 i - 34.29 j + 68.57 k) N T2 = (22.86 i- 34.29 /-68.57 k) N
I. Solve the following problems completely: Show your complete solution and draw the graph. 1. Locate, and find the magnitude and the position of the resultant R at point A of the forces acting on the Fink Truss shown in the figure. Find the couple at point B. Given Figure: 250N 30⁰ 350N 8m 60% 4m 450N 2100N 8m 8m 60⁰ 8m 60% 350N 4m 60⁰ 30⁰ 8m 250N B
ii, If the length of each element is 5m and the k-EA/L is given as shown, analyze the following system by Direct Method of Finite Element. ki - 200 kN/m * - 1000 kN/m ky : 300 kN/m 400 kN 2 Develop the displacement vector b. Develop the force vectors | c. Develop the stifness matrix for each element d. Develop the global matrix for the sytem e. Find the displacement at node 2 £ Find the forces at node 1 and 3.
In picking up a load from position B, a cable tension T of magnitude 24 kN is developed in on the construction crane cable as shown. 18 m A. TY 30 m 5 m 6 m Compute the magnitude of the Position Vector RAB = Rxi + R„j+ Rzk (Answers in m) Answer: Type here to search
For the crank shown in the figure below, draw free body diagrams for each of the three segments (AB, BC, and CD) and determine all reaction forces and moments. The 1000 [N] is acting orthogonal to the plane of the crank and the 1500 [N] load is acting along the axis of the BC segment. Next, use the vector method demonstrated in class (equations given below) to determine the reaction forces at location D. Compare your results between the two methods Assume the mass of the crank is negligible. = -Fext Fint doF ext Mint = 1500N 200 mm 250 mm 1000N A Mext O 25mm diameter round rod bent into the crank 100 mm B