Q5(a)Discuss,the major dıfferences between ticld programmable gatc arrays(FPGAS) and programmable logie devices (PLDS.where an FPGA may be approprate in a streamıng TV system.Simple multiplexers can be used to mimic a number of two-input logicfunctions by appropriate mapping of nputs X X, and SEL Show how themultiplexer shown in figure Q5a can be used to perform the functionF= AOB(b)SELFigure Q5aFigure Q5b (over) shows the schematic of a Xilinx 3000 sennes logic cell MLabel the configuration bits of the various multiplexers n the celL with zeroedconfiguration bits selecting the topmost input to each multuplexer. Eachmultiplexer has -2 ns, the combinatorial loge block is guaranteed to haveWS7 ns, and the D-type flip-flops have t4 ns and r 1 ns(c)We wish to construct a two-bit counter from this logie cell. where Q, and Qare the high and low order outputs of the counter, CLK is the clock signal, ARis an asynchronous reset signal, EN enables the counter, and LD allows inputsD, and Do to be loaded on the next clock edge.

(a) FPGA is a digital logic chip that can be programmed to do almost any kind of digital function.…

(a) Discuss, 1) the major differences between ficld programmable gate arrays (FPGAS) and programmable logic devices (PLDS). where an FPGA may be appropriate in a streaming TV system. Simple multiplexers can be used to mimic a number of two-input logic functions by appropriate mapping of inputs X, X, and SEL Show how the multiplexer shown in figure Q5a can be used to perform the function F=A@B (b) X, SEL-

(a) Discuss, 1) the major differences between ficld programmable gate arrays (FPGAS) and programmable logic devices (PLDS). where an FPGA may be appropriate in a streaming TV system. Simple multiplexers can be used to mimic a number of two-input logic functions by appropriate mapping of inputs X, X, and SEL Show how the multiplexer shown in figure Q5a can be used to perform the function F=A@B (b) X, SEL-

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Similar questions

H.W :- 1) A four logic-signal A,B,C,D are being used to represent a 4-bit binary number with A as the LSB and D as the MSB. The binary inputs are fed to a logic circuit that produces a logic 1 (HIGH) output only when the binary number is greater than 01102-610. Design this circuit. 2) repeat problem 1 for the output will be 0 (LOW) when the binary input is less than 01112-710- Saleem Lateef
To reset IC chips in a system at power-on, the chips must be powered on and working already. That is to say that the reset signal needs to be after the power-on time. Assume that you need to generate a reset signal 1 ms after power-on using an RC circuit, what will be roughly the values of the resistor and capacitor?
What is not a possible solutions to improve performance ..... of PCM?a. Use of linear PCM codesb. Use of non-linear PCM codes tryc. Use of companded systemsd. Increase number of PCM bits
The practical inverters output voltage normally is OSinusoidal waveform ONon-Sinusoidal waveform OQuasi-square waveform
Design a combinational circuit with the four inputs A,B.C, and D, and three outputs X, Y, and Z. When the binary input is odd number, the binary output is one lesser than the input. When the binary input is even number the binary output is one greate than the input. Implement the function using multiplexers with minimal input and select line.
Design the interfacing circuit shown below and write a program to display single digit (between 0 and 9) prime numbers followed by even numbers, the next odd numbers and repeats in 7-segment displays and its equivalent 8-bit binary value in LEDS. a) When displaying Prime numbers, the first 7-segment display must show "P" and the second 7-segment display must show prime numbers one by one b) When displaying Even numbers, the first 7-segment display must show "E" and the second 7-segment display must show even numbers one by one c) When displaying Odd numbers, the first 7-segment display must show "O" and the second 7-segment display must show even numbers one by one
To implement a Full Subtracter, Using TWO 8:1 Multiplexers (ONE for Sum output and ONE for Cout output). Assign (or Connect) X, Y,and Bin variables to the Select Inputs of Multiplexers and connect 1 or 0 to each Data Input.
Q2/A) Design 8x1 multiplexer using 2x1 multiplexer? Q2 B)Simplify the Logic circuit shown below using K-map then draw the Simplified circuit? Q2/C) design logic block diagram for adding 12 to 5 using full adder showing the input for each adder?
USE DIGITAL LOGIC AND DESIGN Part 1: In Figure_4; we have 4-bit Comparator using 2-bit Comparators block. You have to satisfy given condition by applying all data on figure 4. At the end, given condition should produce HIGH output and other two should be LOW. A3 A2 A1 A0 = 1101 and B3 B2 B1 B0 = 1110 Figure_4 Part 2: The serial data-input waveform (Data in) and data-select inputs (S0 and S1) are shown in Figure_5. Determine the data-output waveforms from D0 through D3. Figure_5 Part 3: Decoder can be useful when we have to decode some specific numbers from their equivalent code. Figure 6 has a concept of 3 to 8 line decoder from which you have to generate output waveform from D0 to D7 with proper relationship to input. Figure_6 Part 4: The data-input and…
PLEASE HELP ME , this subject is all about combinational logic design
Q5: Determine the output boolean expression for logic circuit as shown in figure below. x- y- D z-
Design an encoding matrix with diodes and resistors to display a decimal number to on the seven-segment display. You have 10 switches (WO-W9) with one terminal connected to Vec. For decimal number 0, switch 0 (S0) is closed, for decimal number 1, switch 1 (S1) is closed etc. (Switches are on the vertical axis, S0 on top and the outputs are taken on the horizontal axis (Y0-Y6), with “a" on the left and "g" on the right. Note that (Y0-Y6) outputs are used as inputs to seven-segment display. Since these outputs cannot drive the seven segment display LEDS you may need additional bipolar transistors and resistors. The supply voltage is 5V and each LED needs a current of 20mA. Note that this is a design problem and the design is not unique. Do your best! f a a e