Answered: A d.c. series generator supplies the…

A d.c. series generator supplies the load of 5 kW at 250 volts. The armature resistance and series field resistances are 1 ohm and 0.5 ohm respectively. Determine the value of the induced emf.

Delmar's Standard Textbook Of Electricity

7th Edition

ISBN:9781337900348

Author:Stephen L. Herman

Publisher:Stephen L. Herman

Chapter31: Three-phase Alternators

Section: Chapter Questions

Problem 1RQ: What conditions must be met before two alternators can be paralleled together?

See similar textbooks

Related questions

Q: An 8 × 1 multiplexer has inputs A, B, and C connected to the selection inputs S 2 , S 1 , and S 0 ,…

A: As per the data given, Inputs of 8 × 1 multiplexer are A, B, and C. Selection input of multiplexer…

Q: 3 Ampere current is flowing in a circuit having resistance 40 ohms. Find the woltage applied to the…

A: Given: In a circuit, Current I=3 A. Resistance R=40 Ω.

Q: Find the average value of the voltage in the figure in 5 V ov+ O 1.59 V O 63.7 V O 6.37 V O 10.5 V

Q: Implement the Boolean function F(w, x, y, z)=(y+z′)(wx′+w′x) with NOR gates.

A: Determining the simplified function: Fw,x,y,z=y+z'wx'+w'x =y+z'wx'+w'wx'+x…

Q: What is the current through the resistor in the following circuit, if AV=20 V and R= 100 S2? A. 20…

A: Given circuit, where, Voltage, ∆V=20 V Resistance, R=100 Ω

Q: Please show 7 detailed Solution on this Part, and how it become That answer.

Q: B- A Blood warming device contains a 20 mm diameter copper pipe is used to carry warm water, the…

A: SOLUTION GIVEN---> Blood Warming device diameter= 20mm ==>…

Q: 2. A current of 6 A flows for 10 minutes. What charge [3600 C] is transferred?

Q: The ac equivalent circuit of a crystal has these values: L= 3 H, C= 0.03 pF R = 1000 ohm and…

A: We have an AC equivalent circuit of a crystal, Equivalent circuit of AC crystal is as below,…

Q: A 12 pole, 50 Hz, 3 phase induction motor has rotor resistance of 0.12 ohm and standstill reactance…

A: We have an 3-phase induction motor having, Poles (P) = 12 frequency (f) = 50 Hz Rotor resistance…

Q: Part 3: Find the equivalent resistance RabRab for the circuit shown in (Figure 3). 6ΚΩ 4 ΚΩ www 2 ΚΩ…

Q: By substituting the Boolean expression equivalent of the binary operations as defined in Table 2.8 ,…

A: Writing the Ex-OR operation. A⊕B=AB'+A'B Writing the commutative and associative property.…

Q: find F.T the? f(t) = u(t) cos wot let u(t) = TS (W) + J W coswot = πTES (W_Wo +8 (W+wo)

Q: If reflection coefficient for voltage be 0.6, the voltage standing wave ratio (VSWR) is?

A: Given, Reflection coefficient for voltage, Γ=0.6

Q: Exercise (3): Show that Z = dz di(z,t) dz R+ joL VG+jwC using the equations: v(2,1)= V(z)e and…

A: Given : ∂vz,t∂z=-Riz,t-L∂iz,t∂z∂iz,t∂z=-Gvz,t-C∂vz,t∂z vz,t=Vzejωtiz,t=Izejωt Find: The equation of…

Q: 200 V (+1 a. the value of ia, b. the value of ib, c. the value of U., 40 Ω ia 300 Ω i + 0 Σ75 Ω

A: Given, The circuit is,

Q: The following is a truth table of a three-input, four-output combinational circuit:Inputs Outputsx y…

A: Given Inputs and Outputs,

Q: 3. Find Vx if the power supplied by the 5A current source is 50W.

A: It is given that: P5A=50 W

Q: In the circuit shown below each resistor are 10052. If the battery has 30 V potential differences…

A: Given circuit,

Q: Draw a PLA circuit to implement the functionsF1=A′B+AC+A′BC′ F2=(AC+AB+BC)′

A: Given two functions F1 and F2. F1=A′B+AC+A′BC′ F2=(AC+AB+BC)' Draw the PLA circuit.

Q: Simplify the Boolean function F(w, x, y, z)=Σ(4, 5, 6, 7, 12) with don’t-care function d(w, x, y,…

A: from given function construct K map and simplify the function.

Q: QUESTION 1 The secondary phase voltage and current of a delta/star transformer is 420V and 90A…

Q: A transmitter puts out a total power of 2.09 Watts of 30% AM signal. How much power is contained in…

A: Given, Total power of transmitter, Pt=2.09 W. Modulation index, μ=30%=0.03.

Q: element is connected across an AC signal. CH1 and CH2 measures the

Q: (e mra Given an amplifier with an effective noise temperature of 15,000 K and an 8MHZ bandwidth,…

A: Given- Temperature = 15000 K Bandwidth = 8 MHz To find- Thermal noise level =?

Q: Plot the following signals: 1. (a) y(t) = f 8(x)dx (b) 92 (t) = f(x-t)dx (c) ys(t)= (t(u(t)-…

Q: PROBLEM 4: DETERMINE WHICH CIRCUIT ELEMENTS ARE PASSIVE OR ACTIVE, EACH CIRCUIT ELEMENT'S POWER, AND…

Q: Q1) Determine the corona characteristics of a 3-phase line 160 km long, conductor diameter 1.036 cm,…

Q: Please show all steps in the calculation. Thanks. The Advanced Mobile Phone System (AMPS) uses two…

A: Please comment if you need any clarification. If you find my answer useful please put thumbs up.…

Q: Simplify the following Boolean expressions, using three variable K-maps: F(x,y,z)=xy+x′y′z′+x′yz′

A: Given: Simplify the following Boolean expressions, using three variable K-maps: F(x, y,…

Q: The two wattmeter method is used to measure the power in a three-phase load. The wattmeter readings…

A: Given- Three phase load-Wattmeter readings=400W & (-35) WTo Find-The total active power Pactive

Q: Find the voltage Vag in the circuit shown in Fig. 2.27. 10 v 10 Ω 20 Ω A 30 Ω 40 Ω

Q: A 500 V, lap wound d.c. A shunt motor has 90 slots and each has 8 conductors. When the motor…

Q: An alternating current is having an equation I = 125.6 sin 296 r. Find: (1) Frequency (2) R.M.S.…

A: We have an alternating current with the equation of, I = 125.6 Sin 296 t…

Q: Two wire distributors ABC A is feeding on 240 v. AB Loop Impedance is 0.05 + J 0.150 and section…

Q: Q5) For the waveform shown below, find Vrms v(t) A 2 LAA: 4 6 l10 t -1

A: The given waveform is shown below. Find Vrms.

Q: An electrical component has a reliability of 0.95 over 1,500 hours of normal use (note normal use…

A: Given Reliability = 0.95 Usage in hours = 1500 Here the electrical component usage indicates it…

Q: For the system described by the following block diagram: U(s) 91 92 93 94 X(s) 95 Y(s) Find the…

Q: A 415 V, 3-phase voltage is applied to a balanced star-connected 3-phase load of phase impedance (5…

A: We have given an 3-phase voltage which supplies to a balanced star connected 3-phase load with phase…

Q: Determine the efficiency of a high frequency induction furnace which takes 10 minutes to melt 1.815…

A: To determine the efficiency of a high frequency induction furnace, we need the specific heat of…

Q: Low power factor has some adverse impact on both the transmission line and on the consumer…

A: “Low power factor has some adverse impact on both the transmission line and on the consumer…

Q: A 50 MVA, 11 kV three-phase alternator was subjected to different types of faults. The fault…

A: We have been given an 3-phase 50 MVA alternator which was subjected to different types of fault.…

Q: Check which of the following systems is dynamic. a. y(n) = x(-n) b. y(n) = x(n) + x(n-1)

A: Given governing equations of two system. Asked to check which are dynamic?

Q: True or false: For a ring with P nodes, the ratio of the total network bandwidth to the bisection…

A: Network Bandwidth: It represents the best case. NB = bandwidth of each link × no. of link Bisection…

Q: An alternator stator winding protected by a percentage differential relay is shown in the Fig. 5.27.…

A: An alternator winding is protected by percentage differential relay which is shown in figure, Slope…

Q: A mutually coupled circuit has self-inductances of L₁=5 mH L₂=125 mH The coefficient of coupling…

A: Given data, Inductance, L1=5 mH, L2=125 mH Coefficient of coupling Kc=0.9

Q: A sequential circuit has one flip-flop Q, two inputs x and y, and one output S. It consists of a…

A: Considering the sequential circuit. Determining the truth table. x y Q(t) S C=D D=Q(t+1) 0 0 0…

Q: The two wattmeter method is used to measure the power in a three-phase load. The wattmeter readings…

A: Given The two wattmeter method is used for measure the power of three phase load. The readings of…

Q: Find the current through the resistor R = 522 in the following circuit 102 202 Answer: 3 A 30 70 ww…

Q: Consider the following section of a multiloop circuit, with current directions as indicated: zero B…

A: Given circuit,

Concept explainers

Synchronous Generator

In comparison to an asynchronous generator, it is a machine where the rotor speed is equal to the rotating magnetic field produced by the stator, i.e., mechanical speed is equal to the electrical speed, thus called synchronous, and not asynchronous.

Salient Pole Rotor

Salient pole rotor includes a large number of exposed poles mounted on a magnetic wheel. The construction of a bright pole is as shown in the image on the left. The proposed poles are made of metal laminations. The rotor winding is provided on these poles and is supported by pole shoes.

Question

A d.c. series generator supplies the load of 5 kW at 250 volts. The
armature resistance and series field resistances are 1 ohm and 0.5 ohm respectively.
Determine the value of the induced emf.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

The dc armature resistance of delta-connected alternator measured across its two terminal is 0.8 ohm. The effective resistance per phase is?
There are 144 slots in a 3-phase, 16-pole, 50 Hz., star connected alternator. There are 4 conductors in each slot and all the conductors in a phase are connected in series. Coil span is 1500 electrical and the flux per pole is 0.05 Weber sinusoidallly distributed. Calculate the emf induced per phase.
a) A sinewave is having a frequency of 50 Hz and instantaneous value of 150 Volts at 1.2 milli seconds. Find i) The maximum value of sinusoidal voltage waveform and i) The value of voltage at 1.7 milli seconds. b) Determine the instantaneous equation for the voltage waveform shown in figure, if Vp=100 Volts, Time period is 5 milli seconds and 0 =50 degrees. Vp i= 0 Upload your Answers steps in the "Final Answer Submission" Link provided in the Moodle. a) (i) Maximum value = a) (ii) Value of voltage at 1.7 ms b) Angular frequency %3D
The terminal voltage of a 150 kW series generator is 600 V at rated load. The armature resistance is 0.06 ohms and the series field resistance is 0.04 ohms. Find generated emf.
A short shunt compound generator supplies a load of 20 kW at 500 V. The armature, series and shunt field resistance are 0.10 ohm, 0.05 ohm, and 100 ohms respectively. Find the power developed in the armature. Choices: 24600 W 20500 W 22800 W 25400 W
A 6-pole, 3-phase, 60-cycle alternator has 12 slots per pole and four conductors per slot. The winding is 5/6 pitch. There are 2,500,000 maxwells (0.025 weber) entering the armature from each north pole, and this flux is sinusoidally distributed along the air gap. The armature coils are all connected in series. The winding is wye-connected. Determine the open circuit emf of the alternator.
e = 0 Q1: What does happen if we change two currents? a. Q2: What does happen if we have a three-phase four poles machine? Q3: What does happen if we have a two-phase two poles machine? e = 0 Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali Ki. pw --
There are 160 slots in a 3-phase, 8-pole, 50 Hz., star connected alternator. There are 4 conductors in each slot and all the conductors in a phase are connected in series. Coil span is 150° electrical and the flux per pole is 0.08 Weber sinusoidally distributed. Calculate the emf induced per phase.
1.) A 6-pole, 3-phase, 60-Hz alternator has 12 slots per pole and four conductors per slot. The winding is 5/6 pitch. There are 0.025 Wb entering the armature from each north pole, and this flux is sinusoidally distributed along the air gap. The armature coils are all connected in series. The winding is wye-connected. Determine the open circuit emf per phase of the alternator. Subject Electrical machine 2
An Armature runs at 250 r.p.m. and generates an e.m.f. at 50 Hz. There are 216 slots each containing 5 conductors. The winding is distributed and full pitch. All the conductors of each phase are in series and flux per pole is 30 mWb which is sinusoidal distributed.Calculate the number of pole.
8 = 0 Q1: What does happen if we change two currents? Q2: What does happen if we have a three-phase four poles machine? a Q3: What does happen if we have a two-phase two poles machine? Q4: What does happen if we apply a capacitance in phase b and then use same voltage for both phase. Dr. Ali K....p. . --
In a Three-phase alternator, a given field current produces an armature current of 250 A on short-circuit and a generated e.m.f. of 1500 V on open-circuit. Calculate the terminal p.d. when a load of 250 A at 6.6 kV and 0.8 p.f. lagging is switched off. Calculate also the regulation of the alternator at the given load. Subject: Electrical engineering